Shake Table Tests on Suspended Nonstructural Components Anchored in Cyclically Cracked Concrete
Publication: Journal of Structural Engineering
Volume 140, Issue 11
Abstract
Insufficient anchorage of nonstructural components is a substantial cause of earthquake damage. To investigate this issue, shake table tests were conducted on model nonstructural components suspended and supported via anchors cast in cyclically cracked concrete. Concrete slabs supporting the anchored model component were subjected to seismic floor accelerations and corresponding floor-level cyclic crack width histories to simulate the anchor boundary conditions found in concrete structures during an earthquake. For these tests, post-installed anchors, namely, undercut and expansion types, were tested at various seismic demand levels. This paper presents this unique test data and illustrates important seismic anchor performance characteristics. For the investigated case, the measured correlation between anchor load and crack width indicated a low average anchor load level. In addition, the cumulative anchor displacements and achieved ultimate load capacities showed conservatism when compared with results of simulated seismic tests on isolated anchors.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The study presented in this paper was partially funded by the Hilti Corporation. The German Academic Exchange Service (DAAD) provided additional support for the lead author. In addition to the authors, project team members include Profs. Robert Dowell and Jan Hofmann and (former) graduate students Drs. Derrick Watkins and Richard Wood. Oversight committee members include Dr. Matthew Hoehler, Dr. Ulrich Bourgund, Mr. Rainer Hüttenberger, Mr. John Silva of Hilti, and Dean Frieder Seible of UCSD. The assistance of the Charles Lee Powell Laboratory staff during testing, in particular Mr. Paul Greco and Mr. Andy Gundthardt, as well as undergraduate students is greatly appreciated. Opinions, conclusions, and recommendations expressed in this paper are those of the authors and do not necessarily reflect those of the sponsors.
References
American Concrete Institute (ACI). (2007). “Qualification of post-installed mechanical anchors in concrete (ACI 355.2-07) and commentary.” ACI 355.2-07, Detroit.
American Concrete Institute (ACI). (2008). “Building code requirements for structural concrete (ACI 318-08) and commentary (ACI 318R-08).” ACI 318R-08, Detroit.
ASCE. (2010). “Minimum design loads for buildings and other structures: Revision of ANSI/ASCE 7-10.” Reston, VA.
Bachmann, H. (2002). “Erdbebensicherung von Bauwerken (Earthquake Guarding of Buildings).” 2. überarbeitete Auflage, Birkhäuser, Basel (in German).
Baglin, P., and Scott, R. (2000). “Finite element modeling of reinforced concrete beam-column connections.” ACI Struct. J., 97(6), 886–894.
Bergmeister, K. (1988). “Stochastik in der Befestigungstechnik mit realistischen Einflussgrößen (Stochastic in fastening technology under realistic variables).” Ph.D. thesis, Univ. of Innsbruck, Innsbruck, Austria.
Eligehausen, R., and Balogh, T. (1995). “Behavior of fasteners loaded in tension in cracked reinforced concrete.” ACI Struct. J., 92(3), 365–379.
Franchi, A., Rosati, G., Cattaneo, S., Crespi, P., and Muciaccia, G. (2009). “Experimental investigation on post-installed metal anchors subjected to seismic loading in R/C members.” Studi e ricerche Volume 29, Polytechnic of Milan, Graduate school of reinforced concrete structures.
Gergely, P., and Lutz, L. (1968). “Maximum crack width in reinforced concrete flexural members. Causes, mechanisms and control of cracking in concrete.” ACI Struct. J., 87–117.
Gould, N., and Griffin, M. (2003). “Earthquake performance of nonstructural components.” ABS Consulting, International Risk Management Institute, 〈http://www.irmi.com/Expert/Articles/2003/Gould01.aspx〉 (Jun. 6, 2009).
Hoehler, M. (2006). “Behavior and testing of fastenings to concrete for use in seismic applications.” Ph.D. thesis, IWB, Univ. of Stuttgart, Stuttgart, Germany.
Hoehler, M., et al. (2009). “Performance of suspended pipes and their anchorages during shake table testing of a seven-story building.” Earthquake Spectra, 25(1), 71–91.
Kerntechnischer Ausschuss (KTA). (2006). Komponentenstützkonstruktionen mit nichtintegralen Anschlüssen, Teil 3: Serienmäßige Standardhalterungen [Connections of components, Part 3: Standard mount], KTA 3205.3, Sicherheitstechnische Regel des kerntechnischen Ausschusses (KTA), Salzgitter (in German).
Magenes, G. (1989). “Design analysis and calibration of UCSD shake table.” M.S. thesis, Dept. of Structural Engineering, Univ. of California, San Diego.
Mahrenholtz, P., and Eligehausen, R. (2010). “Behavior of anchor groups installed in cracked concrete under simulated seismic actions.” Proc. Conf. on Fracture Mechanics of Concrete Structures (FraMCoS 7), Korea Concrete Institute, Seoul, 816–822.
Mahrenholtz, P., Hutchinson, T., and Eligehausen, R. (2012a). Shake table tests on anchors connecting suspended components to cyclically cracked concrete, SSRP–2012/01, Univ. of California, San Diego, CA.
Mahrenholtz, P., Hutchinson, T., Eligehausen, R., and Hofmann, J. (2012b). “Shake table tests: Seismic performance of anchors connecting non-structural components.” Proc., 15th World Conf. on Earthquake Engineering, International Association for Earthquake Engineering (IAEE), Tokyo.
Nuti, C., and Santini, S. (2008). “Fastening technique in seismic areas: A critical review.” Proc., Conf. on Tailor Made Concrete Structures, 899–905, Taylor & Francis Group, London.
Oh, B.-H., and Kang, Y.-J. (1987). “New formulas for maximum crack width and crack spacing in reinforced concrete flexural members.” ACI Struct. J., 85(2), 103–112.
Paulay, T., and Priestley, N. (1992). Seismic design of reinforced concrete and masonry buildings, Wiley, New York.
Rieder, A. (2009). “Seismic response of post-installed anchors.” Ph.D. thesis, Institut für konstruktiven Ingenieurbau der Universität für Bodenkultur, Vienna, Austria.
Taghavi, S., and Miranda, E. (2003). Response assessment of nonstructural building elements, PEER 2003/05, Pacific Earthquake Engineering Research Center, College of Engineering, Univ. of California, Berkeley, CA.
Watkins, D., Chui, L., Hutchinson, T., and Hoehler, M. (2009). Survey and characterization of floor and wall mounted mechanical and electrical equipment in buildings, SSRP-2009/11, Univ. of California, San Diego, CA.
Watkins, D., and Hutchinson, T. (2011). Seismic performance of nonstructural components anchored in concrete with cyclic cracks, SSRP-2010/07, Univ. of California, San Diego, CA.
Watkins, D., Hutchinson, T., and Hoehler, M. (2012). “Cyclic crack and inertial loading system for investigating anchor seismic behavior.” ACI Struct. J., 109(4), 457–466.
Whittaker, A., and Soong, T. (2003). “An overview of nonstructural components research at three U.S. Earthquake Engineering Research Centers.” Proc., Seminar on Seismic Design Performance, Retrofit of Nonstructural Components in Critical Facilities, Applied Technology Council (ATC), Redwood City, CA, 271–280.
Wood, R., and Hutchinson, T. (2012). “Effects of ground motion scaling on nonlinear higher mode building response.” Earthquake Struct., 3(6), 869–887.
Wood, R., Hutchinson, T., and Hoehler, M. (2010). “Cyclic load and crack protocols for anchored nonstructural components and systems.” SSRP-2009/12, Univ. of California, San Diego, CA.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Nov 16, 2012
Accepted: Oct 24, 2013
Published online: May 19, 2014
Discussion open until: Oct 19, 2014
Published in print: Nov 1, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.