Seismic Laboratory Testing of Energy-Efficient, Staggered-Stud, Wood-Frame Shear Walls
Publication: Journal of Structural Engineering
Volume 141, Issue 3
Abstract
Residential energy use is a significant contributor to greenhouse gas emissions and climate change. Reducing energy efficiency in conventional wood-framed houses are thermal bridges: direct paths that allow heat to flow through the studs instead of the insulation. One suggestion for reducing thermal bridging is the staggered stud (SS) wall. SS walls use bottom and top plates with studs alternating between sides of the wall. This allows sheathing to be applied to both sides while eliminating thermal bridges. A literature review has revealed a lack of laboratory test data for SS walls used as shear walls, raising concerns about their safety. The objective of this study was to evaluate the seismic performance of typical SS walls and compare their behavior to similar conventional walls. Monotonic and cyclic laboratory tests were conducted with and without gypsum wallboard. The staggered stud specimens performed similarly to conventional walls. Some minor differences were identified, but the data raised no immediate concerns about the use of SS walls as an energy efficient option in areas of seismic hazard.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Seneca Sawmill donated the lumber used in this study. Their generous support is gratefully acknowledged. The remainder of the work was supported financially by a grant from the general research fund from the Research Office at Oregon State University. Two individuals were invaluable to this study. Milo Clauson was responsible for setup, testing, and data acquisition. Jason Kelley conducted pilot testing, created the fixture that was used to build test specimens, and provided insight during the project.
References
American Wood Council. (2007). Special design provisions for wind and seismic with commentary, 2005 Ed., American Forest and Paper Association American Wood Council, Washington, DC.
APA—The Engineered Wood Association. (1999). “APA rated siding panels over rigid foam insulating sheathing.”, APA, Tacoma, WA.
APA—The Engineered Wood Association. (2008). “Build energy efficient walls.”, APA, Tacoma, WA.
ASTM. (2006). “Standard practice for static load test for shear resistance of framed walls for buildings.”, West Conshohocken, PA.
ASTM. (2010). “Standard test methods for cyclic (reversed) load test for shear resistance of vertical elements of the lateral force resisting systems for buildings.”, West Conshohocken, PA.
DOE. (2010). Annual energy review 2010, 〈http://www.eia.gov/totalenergy/data/annual/pdf/sec2_4.pdf〉 (Aug. 16, 2012).
FEMA. (2010). “Natural hazards and sustainability for residential buildings.”, Washington, DC.
Fisette, P. (1993). “Bracing foam-sheathed walls.” J. Light Constr.
International Code Council (ICC). (2006). International residential code for one- and two-family dwellings, ICC, Washington, DC.
Kestner D. M., Goupil J., and Lorenz E., eds., (2010). Sustainability guidelines for the structural engineer, ASCE, Reston, VA.
Krigger, J., and Dorsi, C. (2009). Residential energy: Cost savings and comfort for existing buildings, 5th Ed., Saturn Resource Management, Helena, MT.
Sinha, A., and Gupta, R. (2009). “Strain distribution in OSB and GWB in wood-frame shear walls.” J. Struct. Eng., 666–675.
Sutton, M. A., Wolters, W. J., Peters, W. H., Rawson, W. F., and McNeill, S. R. (1983). “Determination of displacements using an improved digital image correlation method.” Image Vis. Comput., 1(3), 133–139.
Straube, J., and Smegal, J. (2011). Building America special research project: High-R walls case study analysis, Building Science, Somerville, MA.
Van de Lindt, J. W. (2004). “Evolution of wood shear wall testing, modeling, and reliability analysis: Bibliography.” Pract. Period. Struct. Des. Constr., 44–53.
Vic-3D [Computer software]. Correlated Solutions, Columbia, SC.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Aug 30, 2012
Accepted: Jun 13, 2013
Published online: Jun 15, 2013
Discussion open until: Aug 10, 2014
Published in print: Mar 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.