Size-Dependent Stress-Strain Model for Unconfined Concrete
Publication: Journal of Structural Engineering
Volume 140, Issue 4
Abstract
The stress-strain behavior of concrete under compression, both in the ascending and descending branches, is crucial in determining both the strength and ductility of reinforced concrete members. This material property is generally determined directly from compression tests of cylinders or prisms. However, it is widely recognized that this material property depends on both the size and shape of the test specimen and the method of measurement. This paper shows that concrete deformation because of compression is both a material property and a shear-friction mechanism and that by taking both of these deformations into account it is possible to derive a stress-strain relationship that is size-dependent. This paper also shows how the stress-strain from cylinder tests of one specific length can be modified to determine the stress-strain relationship for any size of a cylinder. With this new procedure, the authors reanalyzed the results from 380 published tests on unconfined concrete to extract size-dependent strains at the peak stress and then used these results in existing curve-fitting models to produce size-dependent stress-strain models for unconfined concrete. This paper shows how these size-dependent stress-strain models can be used in a size-dependent deformation-based approach to quantify both the strength and ductility of reinforced concrete members.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge the support of both the Australian Research Council ARC Discovery Project DP0985828, “A Unified Reinforced Concrete Model for Flexure and Shear,” and the Univ. of Malaya, Malaysia, Ministry of Higher Education High Impact Research Grant UM.C/HIR/MOHE/ENG/36, “Strengthening Structural Elements for Load and Fatigue Using Advanced Techniques.”
References
Ahmad, S. H., and Shah, S. P. (1982). “Stress-strain curves of concrete confined by spiral reinforcement.” ACI J., 79(6), 484–490.
Ahmad, S. H., and Shah, S. P. (1985). “Behavior of hoop confined concrete under high strain rate.” ACI J., 82(5), 634–647.
Ansari, F., and Li, Q. (1998). “High-strength concrete subjected to triaxial compression.” ACI Mater. J., 95(6), 747–755.
Assa, B., Nishiyama, M., and Watanabe, F. (2001). “New approach for modeling confined concrete. I: Circular columns.” J. Struct. Eng., 743–750.
Attard, M., and Setunge, S. (1996). “Stress-strain relationship of confined and unconfined concrete.” ACI Mater. J., 95(6), 747–755.
Bachman, H. (1970). “Influence of shear and bond on rotational capacity of reinforced concrete beams.” Publications, International Association of Bridge and Structural Engineering (IABSE), Zurich, 30, 11–28.
Balmer, G. G., Jones, V., and McHenry, D. (1949). “Shearing strength of concrete under high triaxial stress computation of Mohr’s envelope as a curve.” Branch of Design and Construction Research and Geology Division Denver, Colorado, U.S. Bureau of Reclamation, Denver, CO.
Bazant, Z. P. (1989). “Identification of strain softening constitutive relation from uniaxial tests by series coupling model for localization.” Cem. Concr. Res., 19(6), 937–977.
Bazant, Z. P., Ozbolt, J., and Eligehausen, R. (1994). “Fracture size effect: Review of evidence for concrete structures.” J. Struct. Eng., 2377–2398.
Benzaid, R., Mesbah, H., and Chikh, N. E. (2010). “FRP confined concrete cylinders: Axial compression experiments and strength model.” J. Reinf. Plast. Compos., 29(16), 2469–2488.
Berthet, J. F., Ferrier, E., and Hamelin, P. (2005). “Compressive behavior of concrete externally confined by composite jackets. Part A: Experimental study.” Constr. Build. Mater., 19(3), 223–232.
Bischoff, P. H., and Perry, S. H. (1995). “Impact behaviour of plain concrete loaded in uniaxial compression.” J. Eng. Mech., 685–693.
British Standards Institution. (1996). “Eurocode 2: Design of Concrete Structures.” DD ENV:1992-1-2, London.
Candappa, D. P., Sanjayan, J. G., and Setunge, S. (2001). “Complete triaxial stress-strain curves of high-strength concrete.” J. Mater. Civ. Eng., 209–215.
Candappa, D. P., Setunge, S., and Sanjayan, J. G. (1999). “Stress versus strain relationship of high strength concrete under high lateral confinement.” Cem. Concr. Res., 29(12), 1977–1982.
Carrasquillo, R. L., Nilson, A. H., and Slate, F. O. (1981). “Properties of high strength concrete subject to short term load.” ACI J., 78(3), 171–177.
Carreira, D. J., and Chu, K. H. (1985). “Stress-strain relationship for plain concrete in compression.” ACI J., 82(6), 797–804.
Chen, Y., Visintin, P., and Oehlers, D. J. (2013). “Mechanism orientated stress-strain model for unconfined concrete.”, School of Civil, Environmental and Mining Engineering, Univ. of Adelaide, SA, Australia.
Cusson, D., and Paultre, P. (1995). “Stress strain model for confined high-strength concrete.” J. Struct. Eng., 468–477.
De Nicolo, B., Pani, L., and Pozzo, E. (1994). “Strain of concrete at peak compressive stress for a wide range of strengths.” Mater. Struct., 27(4), 206–210.
Desayi, P., Iyengar, K. T. S. R., and Reddy, T. S. (1979). “Equation for stress-strain curve of concrete confined in circular steel spiral.” Mater. Struct., 11(65), 339–345.
Dilger, W. H., Koch, R., and Kowalczyk, R. (1984). “Ductility of plain and confined concrete under different strain rates.” ACI J., 81(1), 73–81.
Domone, P. L. J., and Illston, J. M. (2001). Construction materials: their nature and behaviour, 3rd Ed., Spon Press, New York.
Fantilli, A. P., Iori, I., and Vallini, P. (2007). “Size effect of compressed concrete in four point bending RC beams.” Eng. Fract. Mech., 74(1–2), 97–108.
Fédération International de la Précontrainte (CEB-FIP). (1990). “Model Code for the Design of Concrete Structures.” Thomas Telford, London.
Gardner, N. J. (1969). “Triaxial behaviour of concrete.” ACI J., 66(2), 136–158.
Harmon, T. G., Ramakrishnan, S., and Wang, E. H. (1998). “Confined concrete subjected to uniaxial monotonic loading.” J. Eng. Mech., 1303–1309.
Haskett, M., Mohamed Ali, M. S., Oehlers, D. J., and Wu, C. (2009a). “Influence of bond on the hinge rotation of FRP plated beams.” Adv. Struct. Eng., 12(6), 833–843.
Haskett, M., Oehlers, D. J., Mohamed Ali, M. S., and Sharma, S. K. (2010). “The shear friction aggregate interlock resistance across sliding planes in concrete.” Mag. Concr. Res., 62(12), 907–924.
Haskett, M., Oehlers, D. J., Mohamed Ali, M. S., and Sharma, S. K. (2011). “Evaluating the shear-friction resistance across sliding planes in concrete.” Eng. Struct., 33(4), 1357–1364.
Haskett, M., Oehlers, D. J., Mohamed Ali, M. S., and Wu, C. (2009b). “Rigid body moment-rotation mechanism for reinforced concrete beam hinges.” Eng. Struct., 31(5), 1032–1041.
Haskett, M., Oehlers, D. J., Mohamed Ali, M. S., and Wu, C. (2009c). “Yield penetration hinge rotation in reinforced concrete beams.” J. Struct. Eng., 130–138.
Hillerborg, A. (1989). “The compression stress-strain curve for design of reinforced concrete beam.” Fracture mechanics: Application to concrete, American Concrete Institute, Detroit, 281–294.
Hillerborg, A. (1990). “Fracture mechanics concepts applied to moment capacity and rotational capacity of reinforced concrete beams.” Eng. Fract. Mech., 35(1–3), 233–240.
Hognested, E. (1951). “A study of combined bending and axial load in reinforced concrete members.” Bulletin No. 399, Engineering Experiment Station, Univ. of Illinois, IL.
Imran, I., and Pantazopoulou, S. J. (1996). “Experimental study of plain concrete under triaxial stress.” ACI Mater. J., 93(6), 589–601.
Jansen, D. C., and Shah, S. P. (1997). “Effect of length on compressive strain softening of concrete.” J. Eng. Mech., 25–35.
Jansen, D. C., Shah, S. P., and Rossow, E. C. (1995). “Stress-strain results of concrete from circumferential strain feedback control testing.” ACI Mater. J., 92(4), 419–428.
Jiang, T., and Teng, J. G. (2007). “Analysis-oriented stress-strain models for FRP confined concrete.” Eng. Struct., 29(11), 2968–2986.
Karabinis, A. I., and Rousakis, T. C. (2002). “Concrete confined by FRP material: A plasticity approach.” Eng. Struct., 24(7), 923–932.
Karam, G., and Tabbara, M. (2009). “Hoek–Brown strength criterion for actively confined concrete.” J. Mater. Civ. Eng., 110–118.
Kent, D. C., and Park, R. (1971). “Flexural members with confined concrete.” J. Struct. Div., 97(7), 1969–1990.
Kim, J. K., and Eo, S. H. (1990). “Size effect in concrete specimens with dissimilar initial cracks.” Mag. Concr. Res., 42(153), 233–238.
Kotsovos, M. D. (1983). “Effect of testing techniques on the post-ultimate behaviour of concrete in compression.” Mater. Struct., 16(1), 3–12.
Kshirsagar, S., Lopez-Anido, R. A., and Gupta, R. K. (2000). “Environmental aging of fiber-reinforced polymer-wrapped concrete cylinders.” ACI Mater. J., 97(6), 703–712.
Lahlou, K., Aitcin, P. C., and Chaallal, O. (1992). “Behaviour of high-strength concrete under confined stresses.” Cem. Concr. Compos., 14(3), 185–193.
Lee, Y. H., William, K., and Kang, H. D. (1995). “Experimental observation of concrete behaviour under uniaxial compression.” Fracture Mechanics of Concrete Structures, FRAMCOS-2 Conf., Aedificatio Publishers, Freiburg, Germany, 397–414.
Lu, X. B., and Hsu, C. T. (2006). “Behavior of high strength concrete with and without steel fiber reinforcement in triaxial compression.” Cem. Concr. Res., 36(9), 1679–1685.
Mander, J. B., Priestley, M. J. N., and Park, R. (1988). “Theoretical stress-strain model for confined concrete.” J. Struct. Eng., 1804–1826.
Markeset, G., and Hillerborg, A. (1995). “Softening of concrete in compression localization and size effects.” Cem. Concr. Res., 25(4), 702–708.
Matthys, S., Toutanji, H., Audenaert, K., and Taerwe, L. (2005). “Axial load behavior of large-scale columns confined with fiber-reinforced polymer composites.” ACI Struct. J., 102(2), 258–267.
Mattock, A. H. (1974). “Shear transfer in concrete having reinforcement at an angle to the shear plane.” ACI Special Publication, 42(2), 17–42.
Mendis, P., Pendyala, R., and Setunge, S. (2000). “Stress-strain model to predict the full-range moment curvature behavior of high-strength concrete sections.” Mag. Concr. Res., 52(4), 227–234.
Mirmiran, A., and Shahawy, M. (1997). “Behavior of concrete columns confined by fiber composites.” J. Struct. Eng., 583–590.
Mohamed Ali, M. S., Oehlers, D. J., and Griffith, M. C. (2010). “The residual strength of confined concrete.” Adv. Struct. Eng., 13(4), 603–618.
Mohamed Ali, M. S., Oehlers, D. J., Haskett, M., and Griffith, M. C. (2012). “The discrete rotation in reinforced concrete beams.” J. Eng. Mech., 1317–1325.
Nanni, A., and Bradford, N. M. (1995). “FRP jacketed concrete under uniaxial compression.” Constr. Build. Mater., 9(2), 115–124.
Oehlers, D. J. (2010). “The hunt for the elusive concept.” Adv. Struct. Eng., 13(5), 755–772.
Oehlers, D. J., Haskett, M., Mohamed Ali, M. S., Lucas, W., and Muhamad, R. (2011a). “Our obsession with curvature in reinforced concrete modelling.” Adv. Struct. Eng., 14(3), 399–412.
Oehlers, D. J., Mohamed Ali, M. S., Haskett, M., Lucas, W., Muhamad, R., and Visintin, P. (2011b). “FRP reinforced concrete beams: Unified approach based on IC theory.” J. Compos. Constr., 293–303.
Oehlers, D. J., Mohamed Ali, M. S., Griffith, M. C., Haskett, M., and Lucas, W. (2012a). “A generic unified reinforced concrete model.” Struct. Build., 165(1), 27–49.
Oehlers, D. J., Visintin, P., and Haskett, M. (2012b). “The ideal bond characteristics for reinforced concrete members.” Bond in Concrete Conf., Bond, Anchorage, Detailing, Brescia, Italy.
Pessiki, S., Graybeal, B., and Mudlock, M. (2001). “Proposed design of high-strength spiral reinforcement in compression members.” ACI Struct. J., 98(6), 799–810.
Popovics, S. (1973). “A numerical approach to the complete stress–strain curve of concrete.” Cem. Concr. Res., 3(5), 583–599.
Ramesh, K., Seshu, D. R., and Prabhakar, M. (2003). “Constitutive behaviour of confined fibre reinforced concrete under axial compression.” Cem. Concr. Compos., 25(3), 343–350.
Richart, F. E., Brandtzaeg, A., and Brown, R. L. (1928). “Study of the failure of concrete under combined compressive stresses.” Bulletin 185, Engineering Station, Univ. of Illinois, Urbana, IL.
Richart, F. E., Brantzaeg, A., and Brown, R. L. (1929). “The failure of plain and spirally reinforced concrete in compression.” Bulletin No. 185, Engineering Experiment Station, Univ. of Illinois, Urbana, IL.
Rokugo, K., and Koyanagi, W. (1992). “Role of compressive fracture energy of concrete on the failure behaviour of reinforced concrete beam.” Application of fracture mechanics to reinforced concrete, Elsevier Applied Science, New York, 437–464.
Ros, M. (1950). “Material-technological foundation and problems of reinforced concrete.” Bericht No. 162, Eidgenossische Materialprüfungs und Versuchsanstalt für Industrie, Bauwesen and Gewerbe, Zurich, Switzerland.
Rutland, C. A., and Wang, M. L. (1997). “The effects of confinement on the failure orientation in cementitious materials experimental observations.” Cem. Concr. Compos., 19(2), 149–160.
Saatcioglu, M., and Razvi, S. R. (1992). “Strength and ductility of confined concrete.” J. Struct. Eng., 1590–1607.
Sangha, C. M., and Dhir, R. K. (1972). “Strength and complete stress strain relationships for concrete tested in uniaxial compression under different test conditions.” RILEM, 5(6), 361–370.
Sargin, M., Ghosh, S. K., and Handa, V. K. (1971). “Effects of lateral reinforcement upon the strength and deformation properties of concrete.” Mag. Concr. Res., 23(75–76), 99–110.
Scott, B. D., Park, R., and Priestley, M. J. N. (1982). “Stress-strain behavior of concrete confined by overlapping hoops at low and high strain rates.” ACI J., Title No. 79–2, 13–27.
Shah, S. P., and Ahmad, S. H. (1985). “Structural properties of high strength concrete and its implication for precast prestressed concrete.” PCI Journal, 30(6), 92–119.
Shah, S. P., and Sankar, R. (1987). “Internal cracking and strain softening response of concrete under uniaxial compression.” ACI Mater. J., 84(3), 200–212.
Shahawy, M., Mirmiran, A., and Beitelmann, T. (2000). “Tests and modelling of carbon-wrapped concrete columns.” Compos. Part B, 31(6–7), 471–480.
Shehata, I. A. E. M., Carneiro, L. A. V., and Shehata, L. C. D. (2002). “Strength of short concrete columns confined with CFRP sheets.” Mater. Struct., 35(1), 50–58.
Sfer, D., Carol, I., Gettu, R., and Etse, G. (2002). “Study of the behaviour of concrete under triaxial compression.” J. Eng. Mech., 156–163.
Silva, M. A. G., and Rodrigues, C. C. (2006). “Size and relative stiffness effects on compressive failure of concrete columns wrapped with glass FRP.” J. Mater. Civ. Eng., 334–342.
Smith, G. M., and Young, L. E. (1956). “Ultimate Flexural Analysis Based on Stress-Strain Curves of Cylinders.” ACI Journal, Title No. 53–32, 597–609.
Tadros, G. S. (1970). “Plastic rotation of reinforced concrete members subjected to bending, axial load and shear.” Ph.D. thesis, Univ. of Calgary, Calgary, Canada.
Tasdemir, M. A., Tasdemir, C., Akyuz, S., Jefferson, A. D., Lydon, F. D., and Barr, B. I. G. (1998). “Evaluation of strains at peak stress in concrete: A three phase composite model approach.” Cem. Concr. Compos., 20(4), 301–318.
Torrenti, J. M., Benaija, E. H., and Boulay, C. (1993). “Influence of boundary conditions on strain softening in concrete compression test.” J. Eng. Mech., 2369–2384.
Toutanji, H. (1999). “Stress-strain characteristics of concrete columns externally confined with advanced fiber composite sheets.” ACI Mater. J., 96(3), 397–404.
Van Mier, J. G. M. (1984). “Strain softening of concrete under multiaxial loading conditions.” Ph.D. thesis, Eindhoven Univ. of Techology, Eindhoven, The Netherlands.
Van Mier, J. G. M. (1986a). “Multiaxial strain-softening of concrete. Part I: Fracture.” Mater. Struct., 19(3), 179–190.
Van Mier, J. G. M. (1986b). “Multiaxial strain-softening of concrete. Part II: Load-histories.” Mater. Struct., 19(3), 190–200.
Van Mier, J. G. M., et al. (1997). “Strain-softening of concrete in uniaxial compression.” Mater. Struct., 30(4), 195–209.
Van Vliet, M. R. A., and Van Mier, J. G. M. (1996). “Experimental investigation of concrete fracture under uniaxial compression.” Mech. Cohes.-Frict. Mater., 1(1), 115–127.
Visintin, P., Oehlers, D. J., Wu, C., and Haskett, M. (2012a). “A mechanics based hinge analysis for reinforced concrete columns.” J. Struct. Eng.,.
Visintin, P., Oehlers, D. J., Wu, C., and Haskett, M. (2012b). “A mechanics solution for hinges in RC beams with multiple cracks.” Eng. Struct., 36, 61–69.
Visintin, P., Oehlers, D. J., Wu, C., and Griffith, M. C. (2012c). “The cyclic behaviour of reinforced concrete beam hinges.” Earthquake Eng. Struct. Dyn., 41(12), 1591–1608.
Vonk, R. (1992). “Softening of concrete loaded in compression.” Ph.D. thesis, Eindhoven Univ. of Technology, Eindhoven, The Netherlands.
Wang, P. T., Shah, S. P., and Naaman, A. E. (1978). “Stress-strain curves of normal and lightweight concrete in compression.” ACI Struct. J., 75(62), 603–611.
Watstein, D. (1953). “Effect of straining rate on the compressive strength and elastic properties of concrete.” ACI J., 24(8), 729–744.
Wee, T. H., Chin, M. S., and Mansur, M. A. (1996). “Strength-strain relationship of high strength concrete in compression.” J. Mater. Civ. Eng., 70–76.
Xiao, Q. G., Teng, J. G., and Yu, T. (2010). “Behavior and modeling of confined high-strength concrete.” J. Compos. Constr., 249–259.
Xiao, Y., and Wu, H. (2000). “Compressive behavior of concrete confined by carbon fiber composite jackets.” J. Mater. Civ. Eng., 139–146.
Xie, J., Elwi, A. E., and MacGregor, J. G. (1995). “Mechanical properties of three high-strength concretes containing silica fume.” ACI Mater. J., 92(2), 135–143.
Youssef, M. N., Feng, M. Q., and Mosallam, A. S. (2007). “Stress–strain model for concrete confined by FRP composites.” Compos. Part B, 38(5–6), 614–628.
Zhang, M. H., and Gjorv, O. E. (1991). “Mechanical properties of high-strength lightweight concrete.” ACI Mater. J., 88(3), 240–247.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 140 • Issue 4 • April 2014
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Oct 11, 2012
Accepted: May 7, 2013
Published online: May 8, 2013
Published ahead of production: May 9, 2013
Published in print: Apr 1, 2014
Discussion open until: Apr 28, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.