Corotational Model for Cyclic Analysis of Light-Frame Wood Shear Walls and Diaphragms
Publication: Journal of Structural Engineering
Volume 139, Issue 8
Abstract
This paper presents a new two-dimensional shear-wall and diaphragm model developed as part of a Network for Earthquake Engineering Simulation (NEES) Project entitled NEES-Soft: Seismic Risk Reduction for Soft-Story Woodframe Buildings. A large portion of the older multistory buildings in the California region were constructed with a deficiency that makes them vulnerable to collapse in the first story during earthquakes. This deficiency is referred to as soft-story. The new model presented in this paper was developed using a corotational formulation, which makes it suitable for modeling the side-sway collapse of wood shear walls under large displacement as well as estimating the in-plane stiffness of floor diaphragms. To achieve high computational efficiency, a nodal condensation technique is used to eliminate the degrees of freedom (DOFs) associated with the nail connections from the global DOFs of the model. To verify the validity of the new model, the model was coded into a computer program and was used to analyze selected shear walls and diaphragms tested by various institutions and research programs. Good agreement was observed between the test and model-predicted backbone and cyclic curves for shear walls with various gravity loads and different anchorage conditions. The model is highly flexible and has been shown to be able to model older shear wall construction with horizontal sheathing boards and diagonal bracings.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The material presented in this paper is based on work supported in part by the National Science Foundation under Grant No. CMMI-1041631. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the National Science Foundation. The authors would also like to acknowledge Douglas Rammer from the Forest Products Laboratory for providing the test data used in this research.
References
ABAQUS 6.12 [Computer software]. Waltham, MA, Dassault Systemes Simulia Corp.
ANSYS 14.0 [Computer software]. Canonsburg, PA, ANSYS, Inc.
Christovasilis, I. P., and Filiatrault, A. (2010). “A two dimensional numerical model for the seismic collapse assessment of light frame wood structures.” Proc., ASCE Structures Congress, ASCE, Reston, VA.
Christovasilis, I. P., Filiatrault, A., and Wanitkorkul A. (2007). “Seismic test of a full-scale two-story light-frame wood building: NEESWood benchmark test.” NEESWood Project Rep. NW-01, Multidisciplinary Center for Earthquake Engineering Research (MCEER), Buffalo, NY, 832–843.
Dolan, J. D. (1989). “The dynamic responses of timber shear walls,” Ph.D. thesis, Univ. of British Columbia, Vancouver, Canada.
Dolan, J. D., Carradine, D. M., Bott, J. W., and Easterling, W. S. (2001). “Design methodology of diaphragms.” CUREE Pub. No. W-27, CUREE-Caltech Woodframe Project, Pasadena, CA.
Fischer, D., Filiatrault, A., Folz, B., Uang, C.-M., and Seible, F. (2001). “Shake table tests of a two-story woodframe house.” CUREE Pub. No. W-06, CUREE-Caltech Woodframe Project, Pasadena, CA.
Foliente, G. C. (1995). “Hysteresis modeling of wood joints and structural systems.” J. Struct. Eng., 121(6), 1013–1022.
Folz, B., and Filiatrault, A. (2001). “Cyclic analysis of wood shear walls.” J. Struct. Eng., 127(4), 433–441.
Folz, B., and Filiatrault, A. (2004). “Seismic analysis of woodframe structures. I: Model formulation.” J. Struct. Eng., 130(9), 1353–1360.
Gupta, A. K., and Kuo, G. P. (1985). “Behavior of wood-framed shear walls.” J. Struct. Engrg, 111(8), 1722–1733.
Itani, R. Y., and Cheung, C. K. (1984). “Nonlinear analysis of sheathed wood diaphragms.” J. Struct. Eng., 110(9), 2137–2147.
Johnston, A. R., Dean, P. K., and Shenton, H. W., III. (2006). “Effects of vertical load and hold-down anchors on the cyclic response of wood framed shear walls.” J. Struct. Eng., 132(9), 1426–1434.
Judd, J. P., and Fonseca, F. S. (2005). “Analytical model for sheathing-to-framing connections in wood shear walls and diaphragms.” J. Struct. Eng., 131(2), 345–352.
Kasal, B., and Leichti, R. J. (1992). “Nonlinear finite-element model for light-frame stud walls.” J. Struct. Eng., 118(11), 3122–3135.
McGuire, W., Gallagher, R. H., and Ziemian, R. D. (2000). Matrix structural analysis, 2nd Ed., Wiley, Hoboken, NJ.
Mosalam, K. M., Machado, C., Gliniorz, K.-U., Naito, C., Kunkel, E., and Mahin, S. (2002). “Seismic evaluation of asymmetric three-story wood-frame building.” CUREE Pub. No. W-19, CUREE-Caltech Woodframe Project, Pasadena, CA.
Pang, W., Rosowsky, D. V., Pei, S., and van de Lindt, J. W. (2007). “Evolutionary parameter hysteretic model for wood shear walls.” J. Struct. Eng., 133(8), 1118–1129.
Pang, W., Rosowsky, D. V., Pei, S., and van de Lindt, J. W. (2010). “Simplified direct displacement design of a six-story woodframe building and pre-test performance assessment.” J. Struct. Eng., 136(7), 813–825.
Pardoen, G. C., Walman, A., Kazanjy, R. P., Freund, E., and Hamilton, C. H. (2003). “Testing and analysis of one-story and two-story shear walls under cyclic loading.” CUREE Pub. No. W-25, CUREE-Caltech Woodframe Project, Pasadena, CA.
Pei, S., and van de Lindt, J. W. (2011). “Seismic numerical modeling of a six-story light-frame wood building: Comparison with experiments.” J. Earthquake Eng., 15(6), 924–941.
Pei, S., van de Lindt, J. W., Pryor, S. E., Shimizu, H., Isoda, H., and Rammer, D. (2010). “Seismic testing of a full-scale mid-rise building: The NEESWood capstone test.” NEESWood Project Rep. NW-04, Multidisciplinary Center for Earthquake Engineering Research (MCEER), Buffalo, NY.
Risk Management Solutions. (2004). The Northridge California earthquake: 10-year retrospective. Risk Management Solutions, Newark, CA.
Salenikovich, A. J., and Dolan, J. D. (2003). “The racking performance of shear walls with various aspect ratio. I: Monotonic test of fully anchored walls.” Forest Products J., 53(10), 65–73.
Seible, F., Filiatrault, A., and Uang, C.-M., eds. (1999). Proc., Invitational Workshop on Seismic Testing, Analysis and Design of Woodframe Construction, California Universities for Research in Earthquake Engineering (CUREE), Richmond, CA.
Stewart, W. G. (1987). “The seismic design of plywood-sheathed shear walls.” Ph.D. thesis, Univ. of Canterbury, Christchurch, New Zealand.
Trayer, G. W. (1956). “The rigidity and strength of frame walls.” FPL Rep. No. 896, Forest Products Laboratory, Madison, WI.
van de Lindt, J. W., Rosowsky, D. V., Filiatrault, A., Symans, M. D., and Davidson, R. A. (2010). “The NEESWood project in review.” 9th U.S. National & 10th Canadian Conf. on Earthquake Engineering, Earthquake Engineering Research Institute (EERI), Oakland, CA, 291–300.
Xu, J., and Dolan, J. D. (2009). “Development of a wood frame shear wall model in ABAQUS.” J. Struct. Eng., 135(8), 977–984.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Oct 22, 2011
Accepted: Feb 17, 2012
Published online: Feb 22, 2012
Published in print: Aug 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.