Three-Dimensional Hydromechanical Sectional Analysis of Cracked Nonprismatic Concrete Spillway Piers
Publication: Journal of Structural Engineering
Volume 138, Issue 11
Abstract
Several concrete hydraulic structures, such as spillway piers, must be considered three-dimensional (3D) components subjected to 3D loads. A very convenient approach to perform stability analysis of concrete dams is the so-called gravity method, leading to the solution of a PMM problem (axial force and biaxial bending moments , ) assuming linear normal stress distribution. If cracking takes place, water penetrates into the cracks, inducing the development of full uplift pressures (UPs). Sliding safety factors (SSFs) are computed using shear force resultants , , and a Mohr-Coulomb failure criterion while ignoring torsion (VVT). This paper presents a 3D extension of the gravity method for cracked planar concrete sections of arbitrary geometry subjected to arbitrary loads (PMM-VVT). To compute the shear stress distribution, a VVT sectional analysis algorithm has been developed based on the theory of elasticity (TE), including Saint-Venant and warping torsional components combined with triangular 2D finite elements (FEs). Afterward, the SSF on the failure plane is computed from the integration of normal stresses on the remaining uncracked area where the Mohr-Coulomb criterion (considering the shear stresses from the VVT solution) has not been locally exceeded. Two validation examples and a case study of an actual pier are presented to illustrate the accuracy and efficiency of the proposed approach compared with full 3D FE analyses.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The financial support provided by the Quebec Fund for Research on Nature and Technology, and the Natural Science and Engineering Research Council of Canada is acknowledged.
References
Bazant, Z. (1965). “Nonuniform torsion of thin-walled bars of variable section.” IABSE Zurich, 〈https://doi.org/10.5169/seals-20345〉 (Aug. 23, 2012).
Brnic, J., Turkalj, G., and Canadija, M. (2010). “Shear stress analysis in engineering beams using deplanation field of special 2-D finite elements.” Meccanica, 45(2), 227–235.
Canadian Dam Association (CDA). (2007). Dam safety guidelines. CDA, Edmonton, ON, Canada.
Computers and Structures, Inc (CSI). (2009). CSI analysis reference manual for SAP2000, 〈http://www.csiberkeley.com〉 (Jun. 25, 2011).
Dawkins, P. (2007). “Gradient vector, tangent planes and normal lines.” Calculus III, 111–112, 〈http://tutorial.math.lamar.edu/downloadfile.aspx?file=B,11,N〉 (Jun. 25, 2011).
Eisenberger, M. (1995). “Nonuniform torsional analysis of variable and open cross-section bars.” Thin-walled Struct., 21(2), 93–105.
Federal Energy Regulatory Commision (FERC). (2002). “Gravity dams.” Chapter 3. Engineering guidelines for the evaluation of hydropower projects, Dept. of Energy, Washington, D.C.
Furlong, R. W., Hsu, C. T. T., and Mirza, S. A. (2004). “Analysis and design of concrete columns for biaxial bending-overview.” ACI Struct. J., 101(3), 413–423.
Geuzaine, C., and Remacle, J.-F. (2009). “Gmsh: A three-dimensional finite element mesh generator with built-in pre- and post-processing facilities.” Int. J. Numer. Methods Eng., 79(11), 1309–1331.
Gruttmann, F., Sauer, R., and Wagner, W. (1999). “Shear stresses in prismatic beams with arbitrary cross-sections.” Int. J. Numer. Methods Eng., 45(7), 865–889.
Kollbrunner, C. F., and Basler, K. (1969). Torsion in structures, Springer, Berlin.
Leclerc, M., and Léger, P. (2011). CADAM-3D, version 2-user's manual, Ecole Polytechnique de Montréal, Montréal (in French).
Leclerc, M., Léger, P., and Tinawi, R. (2003). “Computer aided stability analysis of gravity dams-CADAM.” Adv. Eng. Software, 34(7), 403–420.
Mason, W. E., and Herrmann, L. R. (1968). “Elastic shear analysis of general prismatic beams.” J. Eng. Mech., 94(EM4), 965–983.
MathWorks (2010). Matlab 7-Programming Tips, 〈http://www.mathworks.com/help/pdf_doc/matlab/programming_tips.pdf〉 (Jun. 25, 2011).
Ministry of National Integration Brezil (BMNI). (2002). Manual for safety and inspection of dams, Brezil, Brasilia (in Portuguese).
Pugsley, A. G., and Weatherhead, R. A. (1942). “The shear stresses in tapered beams.” J. Roy. Aeronaut. Soc., 46(381), 218–226.
Reagan, S. W., and Pilkey, W. D. (2002). “Constrained torsion of prismatic bars.” Finite Elem. Anal. Des., 38(10), 909–919.
Rodriguez, J. M., and Viano, J. M. (1997). “Asymptotic derivation of a general linear model for thin-walled elastic rods.” Comput. Method. Appl. Mech. Eng., 147(3–4), 287–321.
Russo, E. P., and Garic, G. (1992). “Shear-stress distribution in symmetrically tapered cantilever beam.” J. Struct. Eng., 118(11), 3243–3249.
Sapountzakis, E. J., and Mokos, V. G. (2004). “Nonuniform torsion of bars of variable cross section.” Comput. Struc., 82(9–10), 703–715.
Sapountzakis, E. J., and Mokos, V. G. (2007). “3-D beam element of composite cross section including warping and shear deformation effects.” Comput. Struc., 85(1–2), 102–116.
Stefan, L. (2011). “Constitutive hydromechanical three-dimensional model for stability analysis of spillway piers.” Ph.D. thesis, École Polytechnique de Montréal, Montréal (in French).
Stefan, L., and Léger, P. (2008). “Extension of the gravity method for 3D cracking analysis of spillway piers including uplift pressures.” J. Struct. Eng., 134(8), 1278–1287.
Stefan, L., and Léger, P. (2012). “Elastic sectional stress analysis of variable section piers subjected to three-dimensional loads.” Comput. Struc., 90–91, 28–41.
Timoshenko, S. P., and Goodier, J. N. (1970). Theory of elasticity, 3rd Ed., McGraw Hill, Toronto.
U.S. Army Corps of Engineers (USACE). (1995). “Engineering and design: Gravity dam design.” Rep. EM 1110-2-2200, Washington, D.C.
U.S. Bureau of Reclamation (USBR). (1987). Design of small dams, 3rd Ed., U.S. Government Printing Office, Denver.
Yang, W. Y., Cao, W., Chung, T.-S., and Morris, J. (2005). Applied numerical methods using Matlab, Wiley, Hoboken, NJ.
Zienkiewicz, O. C., and Taylor, R. L. (2000). The finite element method. The basis, Vol. 1, 5th Ed., Butterworth-Heinemann, Woburn, MA.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 138 • Issue 11 • November 2012
Pages: 1310 - 1320
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Aug 13, 2011
Accepted: Feb 7, 2012
Published online: Feb 10, 2012
Published in print: Nov 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.