Development of a Reliability Framework for the Use of Advanced Nonlinear Finite Elements in the Design of Concrete Structures
Publication: Journal of Structural Engineering
Volume 138, Issue 8
Abstract
This paper proposes a methodology that uses advanced nonlinear finite-element analysis for determining a global resistance factor for the design of reinforced concrete structures. It introduces a new reliability approach that takes into account the uncertainties of the material properties and the performance of the concrete model used in the calculations. In the proposed approach, the global resistance factor is computed following a procedure in which the coefficient of variation of the calculated resistance is estimated using Rosenblueth’s point-estimate method. The robustness and simplicity of the method are demonstrated through validation examples. It is seen that good approximations of the resistance factor can be achieved for the case of normal or quasi-normal distributions of the resistance. Estimation of the coefficient of variation of the prediction error is then performed for a given reinforced concrete element and a nonlinear finite-element package. The accuracy of the selected software is considered through its ability to predict the behavior of a set of benchmarks selected for the target design structure, going from the material level to the structural level. The suggested methodology is well suited for structural engineers having access to nonlinear deterministic finite-element packages with concrete models. It proposes a reliability format that focuses on the variability on the resistance side while using the concept of critical load paths on the load side, which is compatible with the philosophy of the existing design codes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to acknowledge the financial support obtained from the Natural Sciences and Engineering Council of Canada.
References
Allen, D. E. (1975). “Limit States design—a probabilistic study.” Can. J. Civ. Eng., 2(1), 36–49.CJCEB8
American Concrete Institute (ACI). (1971). “Building code requirements for reinforced concrete.” ACI-318-71, Detroit.
American Concrete Institute (ACI). (2008). “Building code requirements for structural concrete.” ACI-318-08, Detroit.
Barbato, M., Gu, Q., and Conte, J. P. (2010). “Probabilistic push-over analysis of structural and soil-structure systems.” J. Struct. Eng.JSENDH, 136(11), 1330–1341.
Bentz, E., and Collins, P. (2001). “Response-2000, Shell-2000, Triax-2000, Membrane-2000 user manual.” Dept. of Civil Engineering, Univ. of Toronto, Toronto Ont., Canada.
Bertagnoli, G., Giordano, L., and Mancini, G. (2004). “Safety format for the nonlinear analysis of concrete structures.” Stud. Res., 25, 1–26.
Bucher, C. G., and Bourgund, U. (1990). “A fast and efficient response surface approach for structural reliability problems.” Struct. Saf., 7(1), 57–66.
Canadian Standards Association (CSA). (1977). “Design of concrete structures.” CSA Standard A23.3-77, Toronto.
Canadian Standards Association (CSA). (1984). “Design of concrete structures for buildings.” CSA Standard CAN3-A23.3M-84, Toronto.
Cervenka, V. (2008). “Global safety format for nonlinear calculation of reinforced concrete.” Beton-und Stahlbetonbau, 103(S1), 37–42.
Choi, S. K., Grandhi, R. V., and Canfield, R. A. (2007). Reliability-based structural design, Springer, London.
Christian, J. T., and Baecher, G. B. (1999). “Point estimate method as numerical quadrature.” J. Geotech. Geoenviron. Eng., 125(9), 779–786.JGGEFK
Comité Euro-International du Béton (CEB). (1975). “International system of unified technical regulations for structures.” Bulletin d’Information No. 111, Paris.
Comité Euro-International du Béton— Fédération Internationale du Béton (CEB-FIB). (1993). CEB-FIP model code 1990—design code, Thomas Telford, London.
Comité Européen de Normalisation (CEN). (2002). “Design of Concrete Structures—Part 1-1: General actions—densities, self-weight, imposed loads for buildings.” Eurocode 2, Brussels, Belgium.
Conte, J. P. (2001). “Finite-element response sensitivity analysis in earthquake engineering.” Earthquake engineering frontiers in the new millennium, Spencer & Hu, Swets & Zeitlinger, Lisse, Netherlands, 395–401.
Cornell, C. A. (1969). “A probability based structural code.” ACI J.JACIAX, 66(12), 974–985.
Der Kiureghian, A., and Taylor, R. L. (1983). “Numerical methods in structural reliability.” Proc., ICASP4, IABSE and AGI, Florence, Italy.
Deutches Institut für Normung (DIN). (1998). “Tragwerke aus Beton, Stahlbeton und Spannbeton, Teil 1: Bemessung und konstruktion.” DIN 1045, Berlin.
Ditlevsen, O., Melchers, R. E., and Gluver, H. (1990). “General multi-dimensional probability integration by directional simulation.” Comput. Struct., 36(2), 355–368.CMSTCJ
Ellingwood, B. R., Galambos, T. V., MacGregor, J. G., and Cornell, C. A. (1980). “Development of a probability based load criterion for American National Standard A58.” NBS Special Publication 577, National Bureau of Standards, U. S. Dept. of Commerce, Washington, DC.
Fédération Internationale du Béton (FIB). (2008). “Practioners’ guide to finite element modelling of reinforced concrete structures, state-of-art report.” CEB-FIB Bulletin 45, Lausanne, Switzerland.
Frangopol, D. M. (1985). “Structural optimization using reliability concepts.” J. Struct. Eng.JSENDH, 111(11), 2288–2301.
Frangopol, D. M. (2008). Structural design optimization considering uncertainties: Structures & infrastructures book, Vol. 1, Taylor & Francis, London.
Ghanem, R., and Spanos, P. D. (1991). Stochastic finite elements: A spectral approach, Springer, New York.
Gu, Q., Conte, J. P., Elgamal, A., and Yang, Z. (2009). “Finite element response sensitivity analysis of multi-yield-surface plasticity model by direct differentiation method.” Comput. Methods Appl. Mech. Eng., 198(30–32), 2272–2285.CMMECC
Harr, M. E. (1989). “Probabilistic estimates for multivariate analyses.” Appl. Math. Modell.AMMODL, 13(5), 313–318.
Haukaas, T., and Der Kiureghian, A. (2005). “Parameter sensitivity and importance measures in nonlinear finite element reliability analysis.” J. Eng. Mech.JENMDT, 131(10), 1013–1026.
Haukaas, T., and Der Kiureghian, A. (2007). “Methods and object-oriented software for FE reliability and sensitivity analysis with application to a bridge structure.” J. Comput. Civ. Eng., 21(3), 151–163.JCCEE5
Henriques, A. A. R., Calheiros, F., and Figueiras, J. A. (2002). “Safety format for the design of concrete frames.” Eng. Comput., 19(3), 346–363.ENGCE7
Hibbitt, Karlsson and Sorensen (HKS). (2010). “ABAQUS version 6.10, finite element program.” HKS, Providence, RI.
Hisada, T., and Nakagiri, S. (1985). “Role of stochastic finite element method in structural safety and reliability.” Proc., 4th Int. Conf. on Structural Safety and Reliability, International Association for Structural Safety and Reliability, 385–394.
Kleiber, M., Antunez, H., Hien, T. D., and Kowalczyk, P. (1997). Parameter sensitivity in nonlinear mechanics: Theory and finite element computations, Wiley, New York.
Konig, G., Tue, N., and Pommerening, D. (1995). “Safety concept for the application of nonlinear analysis in the design of concrete structures. General considerations.” CEB Bulletin d’Information No. 229, Lausanne, Switzerland, 13–31.
Liu, P. L., and Der Kiureghian, A. (1991). “Finite element reliability of geometrically nonlinear uncertain structures.” J. Eng. Mech.JENMDT, 117(8), 1806–1825.
Liu, W. K., Belytschko, T., and Mani, A. (1986). “Random field finite elements.” Int. J. Numer. Methods Eng.IJNMBH, 23(10), 1831–1845.
MacGregor, J. G. (1976). “Safety and limit states design for reinforced concrete.” Can. J. Civ. Eng., 3(4), 484–513.CJCEB8
Mancini, G. (2002). “Nonlinear analysis and safety format for practice.” Proc., 1st FIB Congress, Prestressed Concrete Engineering, Osaka, Japan, 53–58.
Massicotte, B., Nour, A., Ben Ftima, M., and Yildiz, E. (2007). “EPM3D—a user-supplied constitutive model for the nonlinear finite element analysis of reinforced concrete structures.” Rep. SR07-10, École Polytechnique de Montréal, Montreal Que., Canada.
McKay, M. D., Beckman, R. J., and Conover, W. J. (1979). “A comparison of three methods for selecting values of input variables in the analysis of output from a computer code.” Technometrics, 21(2), 239–245.TCMTA2
Melchers, R. E. (2001). Structural reliability analysis and prediction, 2nd Ed., Wiley, Chichester, UK.
Rajashekhar, M. R., and Ellingwood, B. R. (1993). “A new look at the response surface approach for reliability analysis.” Struct. Saf., 12(3), 205–220.
Rosenblueth, E. (1975). “Point estimates for probability moments.” Proc. Natl. Acad. Sci. U.S.A., 72(10), 3812–3814.PNASA6
Rubinstein, R. Y. (1981). Simulation and the Monte Carlo method, Wiley, New York.
Standards Association of Australia (SAA). (2005). “DR 05252 draft for public comment Australian standard, concrete structures.” Revision of AS 3600-2001, Sydney, Australia.
Wolff, T. F. (1996). “Probabilistic slope stability in theory and practice.” Uncertainty in the geologic environment, ASCE, New York, 419–433.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 138 • Issue 8 • August 2012
Pages: 1054 - 1064
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Nov 1, 2010
Accepted: Nov 17, 2011
Published online: Nov 19, 2011
Published in print: Aug 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.