Experimental Tests of Notched and Plate Connectors for LVL-Concrete Composite Beams
Publication: Journal of Structural Engineering
Volume 137, Issue 2
Abstract
This paper reports the experimental results of symmetrical push-out tests performed on notched and toothed metal plate connectors for laminated veneer lumber (LVL)-concrete composite floor systems. The characteristic shear strength and slip moduli were evaluated for three types of connectors: (1) a 300-mm-long rectangular notch cut in the LVL joist and reinforced with a 16-mm-diameter lag screw; (2) a triangular notch reinforced with the same lag screw; and (3) two 333-mm-long toothed metal plates pressed in the lateral surface of two adjacent LVL joists. The shear force versus relative slip relationships are presented together with analytical prepeak and postpeak approximations which can be used to carry out nonlinear finite-element analyses of LVL-concrete composite beams. The failure mechanisms of the notched connections are also discussed. Analytical design formulas for shear-strength evaluation of notched connections derived in accordance with New Zealand Standards and Eurocodes are proposed based on four possible failure mechanisms. Good approximation was found if a slight modification of the Eurocodes formulas is introduced.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The technical support from Carter Holt Harvey (Mr. Warwick Banks and Mr. Hank Bier), MiTek NZ (Mr. Steve Coll and Mr. Antony Cook), Firth Concrete (Mr. Dene Cook and Mr. Cliff Davis), and Dr. James Mackechnie is gratefully acknowledged, together with the financial contribution provided by Carter Holt Harvey and by the New Zealand government through the FIDA funds. Special thanks to research assistants Ms. Marta Mazzilli and Ms. Jennifer Haskell and technicians at the University of Canterbury, Mr. Norm Pilling and Mr. John Maley.
References
Aicher, S., Klock, W., Dill-Langer, G., and Radovic, B. (2003). “Nails and nailplates as shear connectors for timber-concrete composite constructions.” Otto-Graf J., 14, 189–209.
ANSYS. (2007). Release 11.0 academic teaching advanced, ANSYS Inc., Canonsburg, Pa.
Carter Holt Harvey (CHH). (2007). New Zealand factory production data for LVL Truform recipe from January to May 2007, CHH, Auckland, New Zealand.
Ceccotti, A. (1995). “Timber-concrete composite structures.” Timber engineering STEP 2, 1st Ed., H. Blass et al., eds., Centrum Hout, The Netherlands, E13/1–E13/12.
Ceccotti, A., Fragiacomo, M., and Giordano, S. (2006). “Behavior of a timber-concrete composite beam with glued connection at strength limit state.” Proc., 9th World Conf. on Timber Engineering.
Clouston, P., Bathon, L., and Schreyer, A. (2005). “Shear and bending performance of a novel wood-concrete composite system.” J. Struct. Eng., 131(9), 1404–1412.
Comite European de Normalisation (CEN). (2002). “Eurocode 0: Basis of structural design.” EN 1990, Brussels, Belgium.
Comite European de Normalisation (CEN). (2004a). “Eurocode 2: Design of concrete structures—Part 1.1: General rules and rules for buildings.” EN 1995-1-1, Brussels, Belgium.
Comite European de Normalisation (CEN). (2004b). “Eurocode 5: Design of timber structures—Part 1.1: General rules and rules for buildings.” EN 1995-1-1, Brussels, Belgium.
Comité Européen de Normalisation (CEN). (1991) “Timber structures—Joints made with mechanical fasteners—General principles for the determination of strength and deformation characteristics.” EN 26891, Brussels, Belgium.
Deam, B., Fragiacomo, M., and Buchanan, A. (2007). “Connections for composite concrete slab and LVL flooring systems.” Mat. and Struc., RILEM, 41(3), 495–507.
Deam, B. L., Fragiacomo, M., and Gross, L. S. (2008). “Experimental behavior of prestressed LVL-concrete composite beams.” J. Struct. Eng., 134(5), 801–809.
Fragiacomo, M., Amadio, C., and Macorini, L. (2004). “A finite element model for collapse and long-term analysis of steel-concrete composite beams.” J. Struct. Eng., 130(3), 489–497.
Fragiacomo, M., Amadio, C., and Macorini, L. (2007). “Short- and long-term performance of the ‘Tecnaria’ stud connector for timber-concrete composite beams.” Mat. and Struc., RILEM, 40(10), 1013–1026.
Gutkowski, R., Brown, K., Shigidi, A., and Natterer, J. (2004). “Investigation of notched composite wood-concrete connections.” J. Struct. Eng., 130(10), 1553–1561.
Gutkowski, R., Brown, K., Shigidi, A., and Natterer, J. (2008). “Laboratory tests of composite wood-concrete beams.” Constr. Build. Mater., 22(6), 1059–1066.
Kuhlmann, U., and Michelfelder, B. (2006). “Optimised design of grooves in timber-concrete composite slabs.” Proc., 9th World Conf. on Timber Engineering.
Lukaszewska, E., Fragiacomo, M., and Johnsson, H. (2009). “Laboratory tests and numerical analyses of prefabricated timber-concrete composite floors.” J. Struct. Eng., 136(1), 46−55.
Lukaszewska, E., Johnsson, H., and Fragiacomo, M. (2007). “Performance of connections for prefabricated timber-concrete composite floors.” Mat. and Struc., RILEM, 41(9), 1533–1550.
McCullough, B. (1943). “Oregon tests on composite (timber-concrete) beams.” Proc., American Concrete Institute, 39, 429–438.
Ollgard, G., Slutter, G., and Fischer, W. (1971). “Shear strength of stud connectors in lightweight and normal weight concrete.” AISC Eng J, 8, 55–64.
Owen, B. (1963). Handbook of statistical tables, Addison-Wesley, Reading, Mass.
Pillai, S. U., and Ramakrishnan, P. (1977). “Nail shear connectors in timber-concrete composites.” IE(I) Journal-CI, 58, 34–39.
Pincus, P. (1970). “Behaviour of wood concrete composite beams.” J. Struct. Div., 96(7), 2009–2019.
Richart, F. E., and Williams, C. B. (1943). “Tests of composite timber-concrete beams.” Proc., American Concrete Institute, 39, 253–262.
SFS. (1999). SFS Verbundsystem VB Holz Beton Verbund (SFS connection system for timber-concrete composite structures), SFS Unimarket AG, Heerbrugg, Switzerland, PS50099D.
SFS Intec. (2010). “Fasteners for wood.” ⟨http://www.sfsintec.biz/internet/sfsinten.nsf/PageID/fasteners_wood⟩ (December 2010).
SNZ Standards New Zealand. (1993). “Design timber structures.” NZS 3603, New Zealand.
SNZ Standards New Zealand. (2006). “Concrete structures standard, Part 1: The design of concrete structures.” NZS 3101: Part 1, New Zealand.
Yeoh, D., Fragiacomo, M., Aldi, P., Mazzilli, M., and Kuhlmann, U. (2008a). “Performance of notched coach screw connection for timber-concrete composite floor system.” Proc., 10th World Conf. on Timber Engineering.
Yeoh, D., Fragiacomo, M., Ghafar, H., Buchanan, A., Deam, B., and Crews, K. (2008b). “LVL-concrete composite floor systems: An effective solution for multi-storey timber buildings.” Proc., Australasian Structural Engineering Conf..
Yeoh, D., Fragiacomo, M., Buchanan, A., and Gerber, C. (2009). “Preliminary research towards a semi-prefabricated LVL-concrete composite floor system for the Australasian market.” Australasian J. Struc. Eng., 9(3), 225–238.
Information & Authors
Information
Published In
Copyright
© 2011 ASCE.
History
Received: Aug 8, 2009
Accepted: Jul 23, 2010
Published online: Aug 2, 2010
Published in print: Feb 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.