Response of High-Strength Concrete Columns under Design Fire Exposure
Publication: Journal of Structural Engineering
Volume 137, Issue 1
Abstract
The behavior of RC columns, especially those fabricated from high-strength concrete (HSC), under design fire exposure is not well quantified. Results from fire resistance experiments on six RC columns are presented in this paper. The test variables include concrete strength (permeability), fire scenario, load ratio and the presence of polypropylene fibers in concrete mix. Data from these fire tests is used to validate a macroscopic finite element model specifically developed for tracing the fire response of RC columns. Results from fire tests and numerical studies are used to illustrate the comparative performance of HSC and normal-strength concrete (NSC) columns under design fire conditions. Results from fire experiments show that HSC columns exhibit lower fire resistance than that of NSC columns. However both HSC and NSC columns do not experience failure under most design fire scenarios. The addition of polypropylene fibers to concrete mitigates fire-induced spalling and enhances fire resistance of HSC columns.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research presented in this paper is primarily supported by the National Science Foundation CMMI program (Grant No. NSFCMS 0601178) and Portland Cement Association. Any opinions, findings, and conclusions or recommendations expressed in this paper are those of the writers and do not necessarily reflect the views of the sponsors.
References
American Concrete Institute (ACI). (2007). “Standard method for determining fire resistance of concrete and masonry construction assemblies.” ACI 216.1-07, Detroit.
American Concrete Institute (ACI). (2008). “Building code requirements for reinforced concrete.” ACI 318-08 and Commentary, Detroit.
Anderberg, Y., and Thelandersson, S. (1976). Stress and deformation characteristics of concrete at high temperatures, 2. Experimental investigation and material behaviour model, Lund Institute of Technology, Lund, Sweden.
ASCE. (1992). “Structural fire protection.” Manual no. 78, ASCE Committee on Fire protection, Structural Div., New York.
ASTM. (2008). “Standard methods of fire test of building construction and materials.” ASTM E119-08a, West Conshohocken, Pa.
Dwaikat, M. B. (2009). “Flexural response of reinforced concrete beams exposed to fire.” Ph.D. thesis, Michigan State Univ., East Lansing, Mich.
Dwaikat, M. B., and Kodur, V. K. R. (2008). “A numerical approach for modeling the fire induced restraint effects in reinforced concrete beams.” Fire Saf. J., 43(4), 291–307.
Dwaikat, M. B., and Kodur, V. K. R. (2009). “Hydrothermal model for predicting fire induced spalling in concrete structural systems.” Fire Saf. J., 44, 425–434.
Eurocode 1. (2002). “EN 1991-1-2: Actions on structures. Part 1–2: General actions—Actions on structures exposed to fire.” European Committee for Standardization, Brussels, Belgium.
Feasey, R., and Buchanan, A. H. (2002). “Post flash-over fires for structural design.” Fire Saf. J., 37(1), 83–105.
Harmathy, T. Z. (1967). “A comprehensive creep model.” J. Basic Eng., 89(2), 496–502.
Harmathy, T. Z. (1993). Fire safety design and concrete. Concrete design and construction series, Longman’s, London.
Kalifa, P., Chéné, G., and Galle, C. (2001). “High-temperature behavior of HPC with polypropylene fibers from spalling to microstructure.” Cem. Concr. Res., 31, 1487–1499.
Khoury, G. A. (2009). “Concrete spalling assessment methodologies and polypropylene fibre toxicity analysis in tunnel fires.” Struct. Concr., 9(1), 11–18.
Kodur, V., Dwaikat, M., and Raut, N. (2009). “Macroscopic finite element models for tracing the fire response of reinforced concrete members.” Eng. Struct., 31(10), 2368–2379.
Kodur, V., and Raut, N. (2007). “Fire resistance of reinforced concrete columns–State-of-the-art and research needs.” ACI SP-255-5: Designing concrete structures for fire safety (CD-ROM), American Concrete Institute, Farmington Hills, Mich., 1–24.
Kodur, V. K. R., and Dwaikat, M. B. (2008). “Effect of fire induced spalling on the response of reinforced concrete beams.” Cem. Concr. Res., 2(2), 71–81.
Kodur, V. R., Dwaikat, M. M. S., and Dwaikat, M. B. (2008). “High temperature properties of concrete for fire resistance modeling of structures.” ACI Mater. J., 105(5), 517–527.
Kumar, A. (2003). “Behaviour of RCC beams after exposure to elevated temperatures.” J. Inst. Eng. (India): Civil Engineering Division, 84(3), 165–170.
Neves, I. C., Rodrigues, J. C., and Loureiro, A. P. (1996). “Mechanical properties of reinforcing and prestressing steels after heating.” J. Mater. Civ. Eng., 8(4), 189–194.
Phan, L. T. (2007). “Spalling and mechanical properties of high strength concrete at high temperature.” Concrete under Severe Conditions: Environment & Loading, CONSEC’ 07 Tours, CONSEC Committee, France.
SFPE. (2008). SFPE handbook of fire protection engineering, 4th Ed., P. J. DiNenno, ed., National Fire Protection Association, Quincy, Mass.
Information & Authors
Information
Published In
Copyright
© 2011 ASCE.
History
Received: Sep 21, 2009
Accepted: May 31, 2010
Published online: Jun 15, 2010
Published in print: Jan 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.