Experimental Investigation of the Interaction of Local and Overall Buckling of Stainless Steel I-Columns
This article is a reply.
VIEW THE ORIGINAL ARTICLEThis article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 135, Issue 11
Abstract
This paper describes an experimental program carried out at the University of Sydney to study the interaction of local and overall flexural buckling in stainless steel I-columns. The columns were composed of cold-formed back-to-back channels, connected with sheet metal screws. Two stainless steel alloys were considered: austenitic AISI304 and ferritic AISI404. Tests were carried out to determine the material properties. The results reveal nonlinear stress-strain behavior with low proportionality limit, moderate anisotropy, and enhanced strength as a result of cold working. A total of 24 columns were tested under an axial load, applied with a nominal eccentricity of , where =effective length. The length of the specimens varied between 500 and 3,000 mm in 500-mm increments. Twin specimens were tested for each length. All columns were tested between pinned ends. The research aims to rectify the lack of experimental data on local-overall interaction buckling in stainless steel columns with open cross section.
Get full access to this article
View all available purchase options and get full access to this article.
References
Australian Standard/New Zealand Standard. (1991). “Methods for tensile testing of metals.” AS/NZS 1391, Sydney, Australia.
Australian Standard/New Zealand Standard. (2001). “Cold-formed stainless steel structures.” AS/NZS 4673, Sydney, Australia.
Becque, J., and Rasmussen, K. J. R. (2007). “Experimental investigation of the interaction of local and overall buckling of stainless steel I-sections.” Research Rep. No. 887, School of Civil Engineering, Univ. of Sydney, Sydney, Australia.
Becque, J., and Rasmussen, K. J. R. (2009). “Numerical investigation of the interaction of local and overall buckling of stainless steel I-Columns.” J. Struct. Eng., 135(11), 1349–1356.
Bjorhovde, R. (1972). “Deterministic and probabilistic approaches to the strength of steel columns.” Ph.D. thesis, Lehigh Univ., Bethlehem, Pa.
Gardner, L., and Nethercot, D. A. (2004). “Experiments on stainless steel hollow sections-Part 2: Member behaviour of columns and beams.” J. Constr. Steel Res., 60(9), 1319–1332.
Gardner, L., Talja, A., and Baddoo, N. R. (2006). “Structural design of high-strength austenitic stainless steel.” Thin-Walled Struct., 44, 517–528.
Hasham, A. S., and Rasmussen, K. J. R. (2002). “Nonlinear analysis of locally buckled I-section steel beam-columns.” Australian Journal of Structural Engineering, 3(3), 171–199.
Johnson, A., and Winter, G. (1966). “Behaviour of stainless steel columns and beams.” J. Struct. Eng., 92(ST5), 97–118.
Lecce, M. (2006). “Distortional buckling of stainless steel sections.” Ph.D. thesis, Univ. of Sydney, Sydney, Australia.
Liu, Y., and Young, B. (2003). “Buckling of stainless steel square hollow section compression members.” J. Constr. Steel Res., 59(2), 165–177.
Papangelis, J. P., and Hancock, G. J. (1995). “Computer analysis of thin-walled structural members.” Comput. Struct., 56(1), 157–176.
Rasmussen, K. J. R., Burns, T., Bezkorovainy, P., and Bambach, M. R. (2003). “Numerical modeling of stainless steel plates in compression.” J. Constr. Steel Res., 59(11), 1345–1362.
Rasmussen, K. J. R., and Hancock, G. J. (1993). “Design of cold-formed stainless steel tubular members. I: Columns.” J. Struct. Eng., 119(8), 2349–2367.
Rasmussen, K. J. R., and Rondal, J. (1997). “Strength curves for metal columns.” J. Struct. Eng., 123(6), 721–728.
Talja, A., and Salmi, P. (1995). “Design of stainless steel RHS beams, columns and beam-columns.” Research Rep. No. 1619, VTT Building Technology, Helsinki, Finland.
van den Berg, G. J. (2000). “The effect of the non-linear stress-strain behaviour of stainless steel on member capacity.” J. Constr. Steel Res., 54(1), 135–160.
van der Neut, A. (1969). “The interaction of local buckling and column failure of thin-walled compression members.” Proc., 12th Int. Congress on Applied Mechanics, Springer, Berlin, Germany, 389–399.
Young, B., and Liu, Y. (2003). “Experimental investigation of cold-formed stainless steel columns.” J. Struct. Eng., 129(2), 169–176.
Young, B., and Lui, W. M. (2006). “Tests of cold-formed high strength stainless steel compression members.” Thin-Walled Struct., 44, 224–234.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: May 31, 2008
Accepted: Mar 30, 2009
Published online: Apr 1, 2009
Published in print: Nov 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.