Influence of Ground-Granulated Blast-Furnace Slag on the Structural Performance of Self-Compacting Concrete
Publication: Practice Periodical on Structural Design and Construction
Volume 27, Issue 3
Abstract
In the last decades, the utilization of industrial waste like ground-granulated blast-furnace slag (GGBFS) has proven itself a great asset in the modern construction industry. Aiming at promoting the green housing initiatives, the present study focused on the study of the influence of GGBFS on the structural performance of self-compacting concrete (SCC). In the initial phase of the extensive experimental program, concrete cubes were prepared with the partial replacements of GGBFS (10%, 15%, 20%, 25%, and 30% with cement) and tested against the control mix in order to investigate the associated mechanical properties (compressive strength, tensile splitting strength, and flexural strength). At 20% GGBFS replacement, the optimum compressive strength was noted, and further addition of GGBFS caused a gradual decrease in the mechanical strength properties. This study further investigated the structural properties like axial load-displacement behavior and failure pattern of RC columns and flexural performance of RC slabs with and without the addition of GGBFS. SCC with 20% GGBFS demonstrated relatively better structural performance, causing the formation of smaller crack width/depth/length compared with the control mix. An empirical relationship was also proposed based on the experimental test results (in relation to the mechanical properties) in line with US and Indian standards code of practice.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
References
ACI (American Concrete Institute). 2014. Building code requirements for structural concrete. ACI 318-14. Farmington Hills, MI: ACI.
Ali, M. B., R. Saidur, and M. S. Hossain. 2011. “A review on emission analysis in cement industries.” Renewable Sustainable Energy Rev. 15 (5): 2252–2261. https://doi.org/10.1016/j.rser.2011.02.014.
Aliabdo, A. A., A. E. M. Abd Elmoaty, and M. A. Emam. 2019. “Factors affecting the mechanical properties of alkali activated ground granulated blast furnace slag concrete.” Constr. Build. Mater. 197 (Feb): 339–355. https://doi.org/10.1016/j.conbuildmat.2018.11.086.
Altoubat, S., D. Badran, M. T. Junaid, and M. Leblouba. 2016. “Restrained shrinkage behavior of Self-Compacting Concrete containing ground-granulated blast-furnace slag.” Constr. Build. Mater. 129 (Dec): 98–105. https://doi.org/10.1016/j.conbuildmat.2016.10.115.
ASTM. 2013. Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete. ASTM C618. West Conshohocken, PA: ASTM.
Bernal, S. A., E. D. Rodríguez, R. Mejía De Gutiérrez, M. Gordillo, and J. L. Provis. 2011. “Mechanical and thermal characterisation of geopolymers based on silicate-activated metakaolin/slag blends.” J. Mater. Sci. 46 (16): 5477–5486. https://doi.org/10.1007/s10853-011-5490-z.
Bilodeau, A., and V. M. Malhotra. 2000. “High-volume fly ash system: Concrete solution for sustainable development.” Mater. J. 97 (1): 41–48.
BIS (Bureau of Indian Standard). 1987. Specification for granulated slag for the manufacture of Portland slag cement. IS 12089: 1987. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 1970. Specification for coarse and fine aggregates from natural sources for concrete. IS 383: 1970. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 2000. Plain and reinforced concrete-code of practice. IS 456: 2000. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 2004. Method of tests for strength of concrete (Reaffirmed 2004). IS 516: 1959. New Delhi, India: BIS.
BIS (Bureau of Indian Standard). 2013. Specification for 43 grade ordinary portland cement. IS 8112: 1989. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 2015. Indian standard Portland slag cement: Specification (fourth revision). IS 455: 1989. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 2019. Concrete mix proportioning—Guidelines. IS 10262: 2019. New Delhi, India: BIS.
Bosoaga, A., O. Masek, and J. E. Oakey. 2009. “CO2 capture technologies for cement industry.” Energy Procedia 1 (1): 133–140. https://doi.org/10.1016/j.egypro.2009.01.020.
Brooks, J. J., and A. F. Al-Kaisi. 1990. “Early strength development of portland and slag cement concretes cured at elevated temperatures.” Mater. J. 87 (5): 503–507.
Brouwers, H. J. H., and H. J. Radix. 2005. “Self-compacting concrete: Theoretical and experimental study.” Cem. Concr. Res. 35 (11): 2116–2136. https://doi.org/10.1016/j.cemconres.2005.06.002.
Chidiac, S. E., and D. K. Panesar. 2008. “Evolution of mechanical properties of concrete containing ground granulated blast furnace slag and effects on the scaling resistance test at 28 days.” Cem. Concr. Compos. 30 (2): 63–71. https://doi.org/10.1016/j.cemconcomp.2007.09.003.
Damtoft, J. S., J. Lukasik, D. Herfort, D. Sorrentino, and E. M. Gartner. 2008. “Sustainable development and climate change initiatives.” Cem. Concr. Res. 38 (2): 115–127. https://doi.org/10.1016/j.cemconres.2007.09.008.
Deb, P. S., P. Nath, and P. K. Sarker. 2014. “The effects of ground granulated blast-furnace slag blending with fly ash and activator content on the workability and strength properties of geopolymer concrete cured at ambient temperature.” Mater. Des. 62 (Oct): 32–39. https://doi.org/10.1016/j.matdes.2014.05.001.
Dinakar, P., K. P. Sethy, and U. C. Sahoo. 2013. “Design of self-compacting concrete with ground granulated blast furnace slag.” Mater. Des. 43 (Jan): 161–169. https://doi.org/10.1016/j.matdes.2012.06.049.
Djelloul, O. K., B. Menadi, G. Wardeh, and S. Kenai. 2018. “Performance of self-compacting concrete made with coarse and fine recycled concrete aggregates and ground granulated blast-furnace slag.” Adv. Concr. Constr. 6 (2): 103–121. https://doi.org/10.12989/acc.2018.6.2.103.
EFNARC (European Federation of National Associations Representing for Concrete). 2005. “EFNARC: Specifications and guidelines for self-compacting concrete.” Accessed October 11, 2020. http://www.efnarc.org.
El-Hassan, H., and N. Ismail. 2018. “Effect of process parameters on the performance of fly ash/GGBS blended geopolymer composites.” J. Sustainable Cem.-Based Mater. 7 (2): 122–140. https://doi.org/10.1080/21650373.2017.1411296.
Fonseca, F. S., R. C. Godfrey, and K. Siggard. 2015. “Compressive strength of masonry grout containing high amounts of class F fly ash and ground granulated blast furnace slag.” Constr. Build. Mater. 94 (Sep): 719–727. https://doi.org/10.1016/j.conbuildmat.2015.07.115.
Gesoğlu, M., E. Güneyisi, S. F. Mahmood, H. Ö. Öz, and K. Mermerdaş. 2012. “Recycling ground granulated blast furnace slag as cold bonded artificial aggregate partially used in self-compacting concrete.” J. Hazard. Mater. 235–236 (Oct): 352–358. https://doi.org/10.1016/j.jhazmat.2012.08.013.
Gholampour, A., and T. Ozbakkaloglu. 2017. “Performance of sustainable concretes containing very high volume Class-F fly ash and ground granulated blast furnace slag.” J. Cleaner Prod. 162 (Sep): 1407–1417. https://doi.org/10.1016/j.jclepro.2017.06.087.
Hooton, R. D., K. Stanish, J. P. Angel, and J. Prusinski. 2009. “The effect of ground granulated blast furnace slag (slag cement) on the drying shrinkage of concrete–a critical review of the literature.” Slag Cem. Concr. 79–94.
Hu, Y., Z. Tang, W. Li, Y. Li, and V. W. Y. Tam. 2019. “Physical-mechanical properties of fly ash/GGBFS geopolymer composites with recycled aggregates.” Constr. Build. Mater. 226: 139–151. https://doi.org/10.1016/j.conbuildmat.2019.07.211.
Huntzinger, D. N., and T. D. Eatmon. 2009. “A life-cycle assessment of Portland cement manufacturing: Comparing the traditional process with alternative technologies.” J. Cleaner Prod. 17 (7): 668–675. https://doi.org/10.1016/j.jclepro.2008.04.007.
Islam, A., U. J. Alengaram, M. Z. Jumaat, and I. I. Bashar. 2014. “The development of compressive strength of ground granulated blast furnace slag-palm oil fuel ash-fly ash based geopolymer mortar.” Mater. Des. 56 (Apr): 833–841. https://doi.org/10.1016/j.matdes.2013.11.080.
Jamora, J. B., S. E. L. Gudia, A. W. Go, M. B. Giduquio, and M. E. Loretero. 2020. “Potential CO2 reduction and cost evaluation in use and transport of coal ash as cement replacement: A case in the Philippines.” Waste Manage. 103 (Feb): 137–145. https://doi.org/10.1016/j.wasman.2019.12.026.
Khan, M. Z. N., Y. Hao, and H. Hao. 2016. “Synthesis of high strength ambient cured geopolymer composite by using low calcium fly ash.” Constr. Build. Mater. 125 (Oct): 809–820. https://doi.org/10.1016/j.conbuildmat.2016.08.097.
Kumar, V., A. Kumar, and B. Prasad. 2019. “Mechanical behavior of non-silicate based alkali-activated ground granulated blast furnace slag.” Constr. Build. Mater. 198 (Feb): 494–500. https://doi.org/10.1016/j.conbuildmat.2018.11.282.
Kwon, Y. J. 2005. “A study on the alkali-aggregate reaction in high-strength concrete with particular respect to the ground granulated blast-furnace slag effect.” Cem. Concr. Res. 35 (7): 1305–1313. https://doi.org/10.1016/j.cemconres.2004.09.021.
Lau, C. K., M. R. Rowles, G. N. Parnham, T. Htut, and T. S. Ng. 2019. “Investigation of geopolymers containing fly ash and ground-granulated blast-furnace slag blended by amorphous ratios.” Constr. Build. Mater. 222 (Oct): 731–737. https://doi.org/10.1016/j.conbuildmat.2019.06.198.
Lee, N. K., and H. K. Lee. 2013. “Setting and mechanical properties of alkali-activated fly ash/slag concrete manufactured at room temperature.” Constr. Build. Mater. 47 (Oct): 1201–1209. https://doi.org/10.1016/j.conbuildmat.2013.05.107.
Li, G., and X. Zhao. 2003. “Properties of concrete incorporating fly ash and ground granulated blast-furnace slag.” Cem. Concr. Compos. 25 (3): 293–299. https://doi.org/10.1016/S0958-9465(02)00058-6.
Li, S., F. Sha, R. Liu, W. Li, Z. Li, and G. Wang. 2017. “Properties of cement-based grouts with high amounts of ground granulated blast-furnace slag and fly ash.” J. Mater. Civ. Eng. 29 (11): 04017219. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002083.
Majhi, R. K., and A. N. Nayak. 2019. “Bond, durability and microstructural characteristics of ground granulated blast furnace slag based recycled aggregate concrete.” Constr. Build. Mater. 212 (Jul): 578–595. https://doi.org/10.1016/j.conbuildmat.2019.04.017.
Majhi, R. K., A. N. Nayak, and B. B. Mukharjee. 2020. “Characterization of lime activated recycled aggregate concrete with high-volume ground granulated blast furnace slag.” Constr. Build. Mater. 259 (Oct): 119882. https://doi.org/10.1016/j.conbuildmat.2020.119882.
Mehta, A., and R. Siddique. 2018. “Sustainable geopolymer concrete using ground granulated blast furnace slag and rice husk ash: Strength and permeability properties.” J. Cleaner Prod. 205 (Dec): 49–57. https://doi.org/10.1016/j.jclepro.2018.08.313.
Miura, T., and I. Iwaki. 2000. “Strength development of concrete incorporating high levels of ground granulated blast-furnace slag at low temperatures.” Mater. J. 97 (1): 66–70.
Monteiro, P. J. M., S. A. Miller, and A. Horvath. 2017. “Towards sustainable concrete.” Nat. Mater. 16 (7): 698–699. https://doi.org/10.1038/nmat4930.
Nandanam, K., U. S. Biswal, and P. Dinakar. 2021. “Effect of fly ash, GGBS, and metakaolin on mechanical and durability properties of self-compacting concrete made with 100% coarse recycled aggregate.” J. Hazard. Toxic Radioact. Waste 25 (2): 04021002. https://doi.org/10.1061/(ASCE)HZ.2153-5515.0000595.
Nehdi, M., M. Pardhan, and S. Koshowski. 2004. “Durability of self-consolidating concrete incorporating high-volume replacement composite cements.” Cem. Concr. Res. 34 (11): 2103–2112. https://doi.org/10.1016/j.cemconres.2004.03.018.
Özbay, E., M. Erdemir, and H. I. Durmuş. 2016. “Utilization and efficiency of ground granulated blast furnace slag on concrete properties: A review.” Constr. Build. Mater. 105 (Feb): 423–434. https://doi.org/10.1016/j.conbuildmat.2015.12.153.
Puertas, F., S. Martínez-Ramírez, S. Alonso, and T. Vázquez. 2000. “Alkali-activated fly ash/slag cements. Strength behaviour and hydration products.” Cem. Concr. Res. 30 (10): 1625–1632. https://doi.org/10.1016/S0008-8846(00)00298-2.
Puligilla, S., and P. Mondal. 2013. “Role of slag in microstructural development and hardening of fly ash-slag geopolymer.” Cem. Concr. Res. 43 (1): 70–80. https://doi.org/10.1016/j.cemconres.2012.10.004.
Rajamallu, C., T. Chandrasekhar Reddy, and E. Arunakanthi. 2021. “Service life prediction of self compacted concretes with respect to chloride ion penetration.” Mater. Today: Proc. 46 (Part 1): 677–681. https://doi.org/10.1016/j.matpr.2020.11.746.
Rajarajeswari, A., and G. Dhinakaran. 2016. “Compressive strength of GGBFS based GPC under thermal curing.” Constr. Build. Mater. 126 (Nov): 552–559. https://doi.org/10.1016/j.conbuildmat.2016.09.076.
Ramakrishnan, K., G. Pugazhmani, R. Sripragadeesh, D. Muthu, and C. Venkatasubramanian. 2017. “Experimental study on the mechanical and durability properties of concrete with waste glass powder and ground granulated blast furnace slag as supplementary cementitious materials.” Constr. Build. Mater. 156 (Dec): 739–749. https://doi.org/10.1016/j.conbuildmat.2017.08.183.
Rangan, B. V., and D. Hardjito. 2005. “Studies on fly ash-based geopolymer concrete.” In Vol. 28 of Proc., World Congress Geopolymer, 133–137. Saint Quentin, France: Geopolymer Institute.
Revilla-Cuesta, V., M. Skaf, A. B. Espinosa, and V. Ortega-López. 2021a. “Multi-criteria feasibility of real use of self-compacting concrete with sustainable aggregate, binder and powder.” J. Cleaner Prod. 325 (Nov): 129327. https://doi.org/10.1016/j.jclepro.2021.129327.
Revilla-Cuesta, V., M. Skaf, A. Santamaría, V. Ortega-López, and J. M. Manso. 2021b. “Assessment of longitudinal and transversal plastic behavior of recycled aggregate self-compacting concrete: A two-way study.” Constr. Build. Mater. 292 (Jul): 123426. https://doi.org/10.1016/j.conbuildmat.2021.123426.
Salehi, H., and M. Mazloom. 2019. “Opposite effects of ground granulated blast-furnace slag and silica fume on the fracture behavior of self-compacting lightweight concrete.” Constr. Build. Mater. 222 (Oct): 622–632. https://doi.org/10.1016/j.conbuildmat.2019.06.183.
Sasanipour, H., and F. Aslani. 2020. “Durability properties evaluation of self-compacting concrete prepared with waste fine and coarse recycled concrete aggregates.” Constr. Build. Mater. 236 (Mar): 117540. https://doi.org/10.1016/j.conbuildmat.2019.117540.
Schneider, M., M. Romer, M. Tschudin, and H. Bolio. 2011. “Sustainable cement production-present and future.” Cem. Concr. Res. 41 (7): 642–650. https://doi.org/10.1016/j.cemconres.2011.03.019.
Sethy, K. P., D. Pasla, and U. Chandra Sahoo. 2016. “Utilization of high volume of industrial slag in self compacting concrete.” J. Cleaner Prod. 112 (Part 1): 581–587. https://doi.org/10.1016/j.jclepro.2015.08.039.
Shariq, M., J. Prasad, and H. Abbas. 2013. “Effect of GGBFS on age dependent static modulus of elasticity of concrete.” Constr. Build. Mater. 41 (Apr): 411–418. https://doi.org/10.1016/j.conbuildmat.2012.12.035.
Shariq, M., J. Prasad, and H. Abbas. 2016. “Creep and drying shrinkage of concrete containing GGBFS.” Cem. Concr. Compos. 68 (Apr): 35–45. https://doi.org/10.1016/j.cemconcomp.2016.02.004.
Shariq, M., J. Prasad, and A. Masood. 2010. “Effect of GGBFS on time dependent compressive strength of concrete.” Constr. Build. Mater. 24 (8): 1469–1478. https://doi.org/10.1016/j.conbuildmat.2010.01.007.
Shen, D., Y. Jiao, J. Kang, Z. Feng, and Y. Shen. 2020. “Influence of ground granulated blast furnace slag on early-age cracking potential of internally cured high performance concrete.” Constr. Build. Mater. 233 (Feb): 117083. https://doi.org/10.1016/j.conbuildmat.2019.117083.
Shubbar, A. A., H. Jafer, A. Dulaimi, K. Hashim, W. Atherton, and M. Sadique. 2018. “The development of a low carbon binder produced from the ternary blending of cement, ground granulated blast furnace slag and high calcium fly ash: An experimental and statistical approach.” Constr. Build. Mater. 187 (Oct): 1051–1060. https://doi.org/10.1016/j.conbuildmat.2018.08.021.
Siddique, R., and D. Kaur. 2012. “Properties of concrete containing ground granulated blast furnace slag (GGBFS) at elevated temperatures.” J. Adv. Res. 3 (1): 45–51. https://doi.org/10.1016/j.jare.2011.03.004.
Sousa, V., and J. A. Bogas. 2021. “Comparison of energy consumption and carbon emissions from clinker and recycled cement production.” J. Cleaner Prod. 306 (Jul): 127277. https://doi.org/10.1016/j.jclepro.2021.127277.
Swamy, R. N., and A. Bouikni. 1990. “Some engineering properties of slag concrete as influenced by mix proportioning and curing.” Mater. J. 87 (3): 210–220.
Topçu, I. B., and A. R. Boⓖa. 2010a. “Effect of ground granulate blast-furnace slag on corrosion performance of steel embedded in concrete.” Mater. Des. 31 (7): 3358–3365. https://doi.org/10.1016/j.matdes.2010.01.057.
Topçu, I. B., and T. Uygunoǧlu. 2010b. “Effect of aggregate type on properties of hardened self-consolidating lightweight concrete (SCLC).” Constr. Build. Mater. 24 (7): 1286–1295. https://doi.org/10.1016/j.conbuildmat.2009.12.007.
Van Oss, H. G., and A. C. Padovani. 2003. “Cement manufacture and the environment, Part II: Environmental challenges and opportunities.” J. Ind. Ecol. 7 (1): 93–126. https://doi.org/10.1162/108819803766729212.
Vejmelková, E., M. Keppert, S. Grzeszczyk, B. Skaliński, and R. Černý. 2011. “Properties of self-compacting concrete mixtures containing metakaolin and blast furnace slag.” Constr. Build. Mater. 25 (3): 1325–1331. https://doi.org/10.1016/j.conbuildmat.2010.09.012.
Verma, M., and N. Dev. 2021. “Effect of ground granulated blast furnace slag and fly ash ratio and the curing conditions on the mechanical properties of geopolymer concrete.” Struct. Concr. 1–15. https://doi.org/10.1002/suco.202000536.
Wang, H. Y. 2008. “The effects of elevated temperature on cement paste containing GGBFS.” Cem. Concr. Compos. 30 (10): 992–999. https://doi.org/10.1016/j.cemconcomp.2007.12.003.
Wattanalamlerd, C., and M. Ouchi. 2005. “Flowability of fresh mortar in self-compacting concrete using fly ash.” In Proc., 1st Int. Symp. on Design, Performance and Use of Self-Consolidating Concrete: SCC’2005-China, 261–270. Paris: RILEM Publications SARL.
Xu, J. H., T. Fleiter, W. Eichhammer, and Y. Fan. 2012. “Energy consumption and emissions in China’s cement industry: A perspective from LMDI decomposition analysis.” Energy Policy 50 (Nov): 821–832. https://doi.org/10.1016/j.enpol.2012.08.038.
Yazici, H. 2008. “The effect of silica fume and high-volume Class C fly ash on mechanical properties, chloride penetration and freeze-thaw resistance of self-compacting concrete.” Constr. Build. Mater. 22 (4): 456–462. https://doi.org/10.1016/j.conbuildmat.2007.01.002.
Yazici, H., M. Y. Yardimci, S. Aydin, and A. Ş. Karabulut. 2009. “Mechanical properties of reactive powder concrete containing mineral admixtures under different curing regimes.” Constr. Build. Mater. 23 (3): 1223–1231. https://doi.org/10.1016/j.conbuildmat.2008.08.003.
Zhao, H., W. Sun, X. Wu, and B. Gao. 2015. “The properties of the self-compacting concrete with fly ash and ground granulated blast furnace slag mineral admixtures.” J. Cleaner Prod. 95 (May): 66–74. https://doi.org/10.1016/j.jclepro.2015.02.050.
Zhu, X., M. Zhang, K. Yang, L. Yu, and C. Yang. 2020. “Setting behaviours and early-age microstructures of alkali-activated ground granulated blast furnace slag (GGBS) from different regions in China.” Cem. Concr. Compos. 114 (Nov): 103782. https://doi.org/10.1016/j.cemconcomp.2020.103782.
Information & Authors
Information
Published In
Practice Periodical on Structural Design and Construction
Volume 27 • Issue 3 • August 2022
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Jul 9, 2021
Accepted: Jan 17, 2022
Published online: Mar 17, 2022
Published in print: Aug 1, 2022
Discussion open until: Aug 17, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- undefined Debasree, Ayesha Amrin, Dipti Ranjan Biswal, Kirti Kanta Sahoo, Prateek Kumar Dhir, Utilization of Bottom Ash and Pond Ash as a Partial Replacement for Sand in Cement Mortar and Concrete: A Critical Review, Practice Periodical on Structural Design and Construction, 10.1061/PPSCFX.SCENG-1325, 28, 4, (2023).