Cold-Formed Steel Equal Angles with Complex Edge Stiffeners under Axial-Compression Laboratory Testing, Numerical Simulation, and Design
Publication: Practice Periodical on Structural Design and Construction
Volume 27, Issue 2
Abstract
This paper investigates the axial-compression capacity of cold-formed steel (CFS) equal angle sections with complex edge stiffeners. Both experimental and numerical analyses were carried out. In total, 10 tests were carried out and the results are presented in this paper. Preceding to compression tests, the material properties were determined and initial geometric imperfections of all the test specimens were measured. From the results of compression tests, the specimens were all susceptible to flexural buckling. A numerical model was created using the finite-element (FE) software ABAQUS version 6.11. The results of finite-element analysis (FEA) substantiated with the experimental results. The FE models were found to accurately predict the experimental behavior. Thus, the validated FE models were used for a parametric study to analyze the effect of slenderness ratio and the orientation of edge stiffeners on the axial capacity. The axial strengths obtained from parametric study were compared with the design strengths calculated by the direct strength method (DSM) from the American Iron and Steel Institute (AISI) specification. Upon comparison, it was found that the axial strengths calculated based on the current DSM are overconservative by 58% on an average.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
References
AISI. 1996. North American specification for the design of cold-formed steel structural members. Washington, DC: AISI.
AISI. 2016. North American specification for the design of cold-formed steel structural members. AISI-S100. Washington, DC: AISI.
AS/NZS. 1996. Australia/New Zealand standard: Cold-formed steel structures. AS/NZS 4600. Sydney, Australia: AS/NZS.
AS/NZS. 2018. Australia/New Zealand Standard: Cold-formed steel structures. AS/NZS 4600. Sydney, Australia: AS/NZS.
Behzadi-Sofiani, B., L. Gardner, M. AhmerWadee, P. B. Dinis, and D. Camotim. 2021. “Behaviour and design of fixed-ended steel equal-leg angle section columns.” J. Constr. Steel Res. 182: 106649. https://doi.org/10.1016/j.jcsr.2021.106649.
BIS (Bureau of Indian Standards). 2005. Metallic materials—Tensile testing at ambient temperature. IS 1608. New Delhi, India: BIS.
CUFSM (Constrained and UnConstrained Finite Strip Method). 2018. “Constrained and un constrained finite strip method.” In Thin-walled structure groups, Civil and system engineering. Baltimore: John Hopkins Univ.
Ellobody, E., and B. Young. 2005. “Behavior of cold-formed steel plain angle columns.” J. Struct. Eng. 131 (3): 457–466. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:3(457).
Fasoulakis, Z. C., X. A. Lignos, T. P. Avraam, and S. P. Katsatsidis. 2019. “Investigation on single-bolted cold-formed steel angles with geometric imperfections under compression.” J. Constr. Steel Res. 162: 105733. https://doi.org/10.1016/j.jcsr.2019.105733.
Fasoulakis, Z. C., I. G. Raftoyiannis, and T. P. Avraam. 2017. “Experimental and numerical study on single-bolted cold-formed angles under tension and compression.” Front. Built Environ. 3 (75). https://doi.org/10.3389/fbuil.2017.00075.
Landesmann, D., P. B. Camotim, and R. C. Dinis. 2017. “Short-to-intermediate slender pinended cold-formed steel equal-leg angle columns: Experimental investigation, numerical simulations and DSM design.” Eng. Struct. 132 (Feb): 471–493. https://doi.org/10.1016/j.engstruct.2016.11.034.
Popovic, D., G. J. Hancock, and K. J. R. Rasmussen. 2001. “Compression tests on cold-formed angles loaded parallel with a leg.” J. Struct. Eng. 127 (6): 600–607. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:6(600).
Silvestre, N., P. B. Dinis, and D. P. B. Camotim. 2013. “Developments on the design of cold-formed steel angles.” J. Struct. Eng. 139 (5): 680–694. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000670.
Yan, J., and B. Young. 2002. “Column tests of cold-formed steel channels with complex stiffeners.” J. Struct. Eng. 128 (6): 737–745. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:6(737).
Yan, J., and B. Young. 2004. “Numerical investigation of channel columns with complex stiffeners—Part I: Test verification.” Thin Walled Struct. 42 (6): 883–893. https://doi.org/10.1016/j.tws.2003.12.002.
Young, B. 2004. “Tests and design of fixed-ended cold-formed steel plain angle columns.” J. Struct. Eng. 130 (12): 1931–1940. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:12(1931).
Young, B. 2005. “Experimental investigation of cold-formed steel lipped angle concentrically loaded compression members.” J. Struct. Eng. 131 (9): 1390–1396. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:9(1390).
Young, B., and J. Chen. 2008. “Column tests of cold-formed steel non-symmetric lipped angle sections.” J. Constr. Steel Res. 64 (7–8): 808–815. https://doi.org/10.1016/j.jcsr.2008.01.021.
Young, B., and E. Ellobody. 2005. “Buckling analysis of cold-formed steel lipped angle columns.” J. Struct. Eng. 131 (10): 1570–1579. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:10(1570).
Young, B., and E. Ellobody. 2007. “Design of cold-formed steel unequal angle compression members.” Thin Walled Struct. 45 (3): 330–338. https://doi.org/10.1016/j.tws.2007.02.015.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Feb 2, 2021
Accepted: Dec 2, 2021
Published online: Feb 24, 2022
Published in print: May 1, 2022
Discussion open until: Jul 24, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Lulu Zhang, Andi Su, Ou Zhao, Flexural–torsional buckling of pin-ended press-braked S690 high strength steel angle section columns: Testing, modelling and design, Thin-Walled Structures, 10.1016/j.tws.2022.110217, 182, (110217), (2023).