Simplified Analytical Models to Predict Low-Velocity Impact Response of RC Beams
Publication: Practice Periodical on Structural Design and Construction
Volume 23, Issue 2
Abstract
Nowadays, evaluation of the impact resistance of structures is receiving immense attention among engineers and researchers because of the increase in accidental and/or malicious incidents around the world. Although numerous experiments and nonlinear finite-element dynamic analysis (NLFEDA) have been carried out in the past to investigate the behavior of RC structures under impact loading, such approaches may not be applicable for routine analysis. Thus, in this study, simplified analytical models, such as energy-balance and single-degree-of-freedom (SDOF) models, were developed to predict the maximum midspan deflection of a beam, and the results were compared with the results of low-velocity impact testing conducted by the author and other researchers. Maximum midspan deflection is considered to be an important performance index to evaluate the damage levels of beams when subjected to impact loadings. Therefore, this study provides efficient yet simple tools to practicing engineers for the preliminary analysis and design of RC beams under low-velocity impact prior to the use of detailed finite-element (FE) analysis and/or laboratory testing.
Get full access to this article
View all available purchase options and get full access to this article.
References
Adhikary, S. D., Li, B., and Fujikake, K. (2012). “Dynamic behavior of reinforced concrete beams under varying rates of concentrated loading.” Int. J. Impact Eng., 47, 24–38.
Adhikary, S. D., Li, B., and Fujikake, K. (2013). “Strength and behavior in shear of reinforced concrete deep beams under dynamic loading conditions.” Nucl. Eng. Des., 259, 14–28.
Adhikary, S. D., Li, B., and Fujikake, K. (2015a). “Residual resistance of impact-damaged reinforced concrete beams.” Mag. Concr. Res. J., 67(7), 364–378.
Adhikary, S. D., Li, B., and Fujikake, K. (2015b). “Low velocity impact response of reinforced concrete beams: Experimental and numerical investigation.” Int. J. Prot. Struct., 6(1), 81–111.
Adhikary, S. D., Li, B., and Fujikake, K. (2016). “State-of-the-art review on low velocity impact response of reinforced concrete beams.” Mag. Concr. Res., 68(14), 701–723.
Banthia, N. (1987). “Impact resistance of concrete.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of British Columbia, Vancouver, BC, Canada.
Bhatti, A. Q., Kishi, N., Mikami, H., and Ando, T. (2009). “Elasto-plastic impact analysis of shear-failure-type RC beams with shear rebars.” Mater. Des., 30(3), 502–510.
CEB (Comité Euro-International du Béton). (1993). CEB-FIP model code 1990, Redwood Books, Trowbridge, Wiltshire, U.K.
CEB (Comité Euro-International du Béton). (2010). CEB-FIP model code 2010, Vol. I, International Federation for Structural Concrete, Lausanne, Switzerland.
Chen, Y., and May, I. M. (2009). “Reinforced concrete members under drop-weight impacts.” Proc. Inst. Civ. Eng. Struct. Build., 162(1), 45–56.
Fu, H. C., Erki, M. A., and Seckin, M. (1991). “Review of effects of loading rate on reinforced concrete.” J. Struct. Eng., 3660–3679.
Fujikake, K., Li, B., and Soeun, S. (2009). “Impact response of reinforced concrete beam and its analytical evaluation.” J. Struct. Eng., 938–950.
Grote, D. L., Park, S. W., and Zhou, M. (2001). “Dynamic behavior of concrete at high strain rates and pressures: I. Experimental characterization.” Int. J. Impact Eng., 25(9), 869–886.
Hughes, G., and Beeby, A. W. (1982). “Investigation of the effect of impact loading on concrete beams.” Struct. Eng., 60(15), 45–52.
Keenan, W. A., and Feldman, A. (1960). “The yield strength of intermediate grade reinforcing bars under rapid loading. Behavior and design of deep structural members, Part 6.” ASFWC-TR-59-72, Air Force Special Weapons Centre, Kirtland Air Force Base, NM.
Kishi, N., and Bhatti, A. Q. (2010). “An equivalent fracture energy concept for nonlinear dynamic response analysis of prototype RC girders subjected to falling-weight impact loading.” Int. J. Impact Eng., 37(1), 103–113.
Kishi, N., and Mikami, H. (2012). “Empirical formulas for designing reinforced concrete beams under impact loading.” ACI Struct. J., 109(4), 509–519.
Kishi, N., Mikami, H., and Ando, T. (2001b). “An applicability of the FE impact analysis on shear-failure-type RC beams with shear reinforcement.” Proc., 4th Asia-Pacific Conf. on Shock and Impact Loads on Structures, CI-Premier, Singapore, 309–315.
Kishi, N., Mikami, H., Matsuoka, K. G., and Ando, T. (2002). “Impact behavior of shear-failure type RC beams without shear rebar.” Int. J. Impact Eng., 27(9), 955–968.
Kishi, N., Nakano, O., Matsouka, K. G., and Ando, T. (2001a). “Experimental study on ultimate strength of flexural-failure-type RC beams under impact loading.” Transactions SMiRT 16, North Carolina State Univ., Raleigh, NC.
Li, Q. M., and Meng, H. (2003). “About the dynamic strength enhancement of concrete-like material in a split Hopkinson pressure bar test.” Int. J. Solid Struct., 40(2), 343–360.
Malvar, L. J. (1998). “Review of static and dynamic properties of steel reinforcing bars.” ACI Mater. J., 95(5), 609–616.
Malvar, L. J., and Ross, C. A. (1998). “Review of strain rate effects for concrete in tension.” ACI Mater. J., 95(6), 735–739.
Saatci, S., and Vecchio, F. (2009). “Effects of shear mechanisms on impact behavior of reinforced concrete beams.” ACI Struct. J., 106(1), 78–86.
Soroushian, P., Choi, K.-B., and Alhamad, A. (1986). “Dynamic constitutive behavior of concrete.” ACI J., 83(2), 251–259.
Sugano, T., et al. (1993). “Full-scale aircraft impact test for evaluation of impact force.” Nucl. Eng. Des., 140(3), 373–385.
Sun, C. T., and Yang, S. H. (1980) “Contact law and impact response of laminated composites.” Rep. No. NASA CR-159884, Purdue Univ. School of Aeronautics and Astronautics, West Lafayette, IN.
Tachibana, S., Masuya, H., and Nakamura, S. (2010). “Performance based design of reinforced concrete beams under impact.” Nat. Hazards Earth Syst. Sci., 10(6), 1069–1078.
Tedesco, J. W., Powell, J. C., Ross, C. A., and Hughes, M. L. (1997). “A strain-rate dependent concrete material model for ADINA.” Comput. Struct., 64(5–6), 1053–1067.
Tedesco, J. W., and Ross, C. A. (1998). “Strain-rate-dependent constitutive equations for concrete.” J. Pressure Vessel Technol., 120(4), 398–405.
Wakabayashi, M., Nakamura, T., Yoshida, N., Iwai, S., and Watanabe, Y. (1980). “Dynamic loading effects on the structural performance of concrete and steel materials and beams.” Proc., 7th World Conf. on Earthquake Engineering, Turkish National Committee on Earthquake Engineering, Istanbul, Turkey, 271–278.
Xiao, S., Li, H., and Monteiro, P. J. M. (2010). “Influence of strain rate and load histories on the tensile damage behaviour of concrete.” Mag. Concr. Res., 62(12), 887–894.
Xiao, Y., Li, B., and Fujikake, K. (2016). “Experimental study of reinforced concrete slabs under different loading rates.” ACI Struct. J., 113(1), 157–168.
Yuan, P., and Harik, I. E. (2010). “Equivalent barge and flotilla impact forces on bridge piers.” J. Bridge Eng., 523–532.
Zhou, X. Q., and Hao, H. (2008). “Modelling of compressive behaviour of concrete-like materials at high strain rate.” Int. J. Solid Struct., 45(17), 4648–4661.
Information & Authors
Information
Published In
Copyright
© 2018 American Society of Civil Engineers.
History
Received: May 4, 2017
Accepted: Sep 7, 2017
Published online: Jan 4, 2018
Published in print: May 1, 2018
Discussion open until: Jun 4, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.