Evaluation of a Four-Point Bending-Test Method for Interface Shear Transfer in Concrete Members
Publication: Practice Periodical on Structural Design and Construction
Volume 22, Issue 4
Abstract
Interface shear transfer (IST) is critical for achieving composite behavior in many concrete structures, such as between precast girders and cast-in-place decks. IST capacity has traditionally been tested using a push-off test method, in which direct shear is induced through compression loads placed at the ends of notched test specimens. In this study, a four-point bending test method as proposed by Iosipescu in 1967 was investigated for application to IST. The four-point bending test creates direct shear by strategically placing supports and loads on a beam. Its advantage is that the test specimens are easy to fabricate. In addition, it produces a more uniform stress state at the interface than the interface stress distribution of the push-off test, making the four-point bending test a better representation of the stress state at cast-in-place deck and bridge girder connections. In this study, these two test methods are compared and contrasted through an experimental program and analytical modeling. The conditions under which the proposed test method are similar and distinct from the push-off method are identified.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors thank Dr. Thomas Cousins and Glenn Department of Civil Engineering staff members Daniel Metz, Samuel Biemann, and Scott Black for their assistance during the test program. Clemson University graduate students Luay Abo-Alarab, Indika Mapa, Sachin Sreedhara, and Mikayla Bladow are also acknowledged for their assistance with the experimental program.
References
AASHTO. (2014). AASHTO LRFD bridge design specifications, 7th Ed., Washington, DC.
Abaqus 6.14-1 [Computer software]. Dassault Systémes Simulia Corp., Providence, RI.
ACI (American Concrete Institute) and International Organization for Standardization. (2014). “Building code requirements for structural concrete and commentary.” ACI 318-14, Farmington Hills, MI.
ASTM. (1997). Standard test methods for shear properties of composite materials by the v-notched beam method, West Conshohocken, PA.
Banta, T. E. (2005). “Horizontal shear transfer between ultra-high performance concrete and lightweight concrete,” Doctoral dissertation, Virginia Polytechnic Institute and State Univ., Blacksburg, VA.
Birkeland, P. W., and Birkeland, H. W. (1966). “Connections in precast concrete construction.” J. Proc., 63(3), 345–368.
British Standards Institute. (2004). Eurocode 2: Design of concrete structures, London.
CSA (Canadian Standard Association). (2014). CSA Standard A23.3-14, Mississauga, Ontario, Canada.
Guenther, C. L. (2007). “Evaluation of shear and diagonal tension in plain concrete.” M.S. thesis, Univ. of Wyoming, Laramie, WY.
Guenther, C., Toker-Beeson, S., and Tanner, J. E. (2016). “Evaluation of shear and diagonal tension in plain concrete.” Concr. Int., 38(1), 39–46.
Hofbeck, J. A., Ibrahim, I. O., and Mattock, A. H. (1969). “Shear transfer in reinforced concrete.” ACI J., 66(2), 119–128.
Hsu, T. T., Mau, S. T., and Chen, B. (1987). “Theory on shear transfer strength of reinforced concrete.” ACI Struct. J., 84(2), 149–160.
Iosipescu, N. (1967). “New accurate procedure for single shear testing of metals.” J. Mater., 2(3), 537–566.
Jimenez-Perez, R., Gergely, P., and White, R. N. (1978). “Shear transfer across cracks in reinforced concrete.” Rep. No. PB-288885, Cornell Univ., Ithaca, NY.
Johal, L. (1975). “Shear transfer in reinforced concrete with moment or tension acting across the shear plane.” PCI J., 77.
Mast, R. F. (1968). “Auxiliary reinforcement in concrete connections.” J. Struct. Div., 94(6), 1485–1504.
Mattock, A. H., and Hawkins, N. M. (1972). “Shear transfer in reinforced concrete—Recent research.” PCI J., 17(2), 55–75.
Mattock, A. H., Li, W. K., and Wang, T. C. (1976). “Shear transfer in lightweight reinforced concrete.” PCI J., 21(1), 20–39.
Loov, R. E., and Patnaik, A. K. (1994). “Horizontal shear strength of composite concrete beams with a rough interface.” PCI J., 39(1), 48–69.
Ross, B. E. (2002). “Analytical modeling and standardized testing of concrete beams with web bonded FRP shear reinforcement.” Masters Abstr. Int., 45(6).
Santos, P. M., and Júlio, E. N. (2011). “Factors affecting bond between new and old concrete.” ACI Mater. J., 108(4), 449–456.
Santos, P. M., and Júlio, E. N. (2012). “A state-of-the-art review on shear-friction.” Eng. Struct., 45(Dec), 435–448.
Walraven, J., Frenay, J., and Pruijssers, A. (1987). “Influence of concrete strength and load history on the shear friction capacity of concrete members.” PCI J., 32(1), 66–84.
Information & Authors
Information
Published In
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Nov 7, 2016
Accepted: Feb 23, 2017
Published online: May 24, 2017
Discussion open until: Oct 24, 2017
Published in print: Nov 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.