Shear Capacity of Ultrahigh-Performance Concrete with Monolithic Interface and Wet-Joint Interface
Publication: Journal of Materials in Civil Engineering
Volume 34, Issue 7
Abstract
A total of 65 Z-shaped ultrahigh-performance concrete (UHPC) specimens with monolithic interfaces, flat-wet-joint interfaces (roughened with a high-pressure water jet), and keyed-wet-joint interfaces were tested under the classical push-off test setup. The influences of steel fiber properties, keyed-joint shapes, and confining stress on the shear strength of the UHPC specimens are discussed. A high-precision equation for predicting the shear capacity of the UHPC specimens with monolithic interfaces, flat-wet-joint interfaces, and keyed-wet-joint interfaces is proposed and verified by experimental results. The test results indicate that steel fibers had a significantly positive effect on improving the shear strength of the UHPC specimens. For the flat-wet-joint specimens, the shear strength increased approximately linearly as the fiber content increased. Using long and hooked-end fibers improved its shear strength. For the keyed-wet-joint specimens, the shear strength improved almost linearly with confining stress, whereas the keyed-joint shape had little influence. The strength reduction factor (the ratio of the ultimate shear strength of the flat-wet-joint interface to that of the monolithic interface) increased with the fiber volume fraction. A relationship between the strength reduction factor and the fiber characteristic parameter is proposed.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
This research is supported by the National Natural Science Foundation Project of China (Grant Nos. 52078059, 51778069, 51978081, and 51808055), the Horizon 2020-Marie Skłodowska-Curie Individual Fellowship of European Commission (REUSE) (793787), and the Natural Science Foundation of Hunan Province, China (Grant No. 2021JJ30712). In addition, the financial support from the China Scholarship Council (CSC) to the first author is gratefully acknowledged.
References
AASHTO. 2003. AASHTO LRFD bridge design specifications. 2th ed. Washington, DC: AASHTO.
ACI (American Concrete Institute). 2005. Building code requirements for structural concrete. ACI 318M-05. Farmington Hills, MI: ACI.
AFNOR (Association Française de Normalisation). 2016. National addition to Eurocode 2—Design of concrete structures: Specific rules for Ultra-High Performance Fibre-Reinforced Concrete (UHPFRC). Paris, France: AFNOR.
Ahmed, G. H., and O. Q. Aziz. 2019. “Shear behavior of dry and epoxied joints in precast concrete segmental box girder bridges under direct shear loading.” Eng. Struct. 182 (Mar): 89–100. https://doi.org/10.1016/j.engstruct.2018.12.070.
Boulekbache, B., M. Hamrat, M. Chemrouk, and S. Amziane. 2012. “Influence of yield stress and compressive strength on direct shear behaviour of steel fibre-reinforced concrete.” Constr. Build. Mater. 27 (1): 6–14. https://doi.org/10.1016/j.conbuildmat.2011.07.015.
Feng, Z., C. Li, J. He, L. Ke, Z. Lei, and G. Vasdravellis. 2021a. “Static and fatigue test on lightweight UHPC-OSD composite bridge deck system subjected to hogging moment.” Eng. Struct. 228 (Aug): 111610. https://doi.org/10.1016/j.engstruct.2021.112459.
Feng, Z., C. Li, D.-Y. Yoo, R. Pan, J. He, and L. Ke. 2021b. “Flexural and cracking behaviors of reinforced UHPC beams with various reinforcement ratios and fiber contents.” Eng. Struct. 248 (Dec): 113266. https://doi.org/10.1016/j.engstruct.2021.113266.
French, R., E. Maher, M. Smith, M. Stone, J. Kim, and T. Krauthammer. 2017. “Direct shear behavior in concrete materials.” Int. J. Impact Eng. 108 (Oct): 89–100. https://doi.org/10.1016/j.ijimpeng.2017.03.027.
Hussein, H. H., S. M. Sargand, F. T. Al-Rikabi, and E. P. Steinberg. 2017. “Laboratory evaluation of ultrahigh performance concrete shear key for prestressed adjacent precast concrete box girder bridge.” J. Bridge Eng. 22 (2): 04016113. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000987.
Jang, H.-O., H.-S. Lee, K. Cho, and J. Kim. 2017. “Experimental study on shear performance of plain construction joints integrated with ultra-high performance concrete (UHPC).” Constr. Build. Mater. 152 (Oct): 16–23. https://doi.org/10.1016/j.conbuildmat.2017.06.156.
Jiang, H., T. Shao, Z. Fang, J. Xiao, and Z. Hu. 2021. “Shear-friction behavior of grooved construction joints between a precast UHPC girder and a cast-in-place concrete slab.” Eng. Struct. 228 (Feb): 111610. https://doi.org/10.1016/j.engstruct.2020.111610.
Jiang, H., R. Wei, Z. J. Ma, Y. Li, and Y. Jing. 2016. “Shear strength of steel fiber-reinforced concrete dry joints in precast segmental bridges.” J. Bridge Eng. 21 (11): 04016085. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000968.
JSCE (Japan Society of Civil Engineers). 2006. Recommendations for design and construction of ultra high strength fiber reinforced concrete structures (draft). JSCE Guideline for Concrete No. 9. Tokyo: JSCE.
JSCE (Japan Society of Civil Engineers). 2010. Standard specifications for concrete structures—2007: ‘Design’. Tokyo: JSCE.
Kim, Y.-J., W.-J. Chin, and S.-J. Jeon. 2018. “Interface shear strength at joints of ultra-high performance concrete structures.” Int. J. Concr. Struct. Mater. 12: 2–14. https://doi.org/10.1186/s40069-018-0298-8.
Li, C., Z. Feng, L. Ke, R. Pan, and J. Nie. 2019. “Experimental study on shear performance of cast-in-place ultra-high performance concrete structures.” Materials 12 (19): 3254. https://doi.org/10.3390/ma12193254.
Li, C., Z. Feng, R. Pan, L. Ke, J. He, and S. Dong. 2020. “Experimental and numerical investigation on the anchorage zone of prestressed UHPC box-girder bridge.” J. Bridge Eng. 25 (6): 04020028. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001556.
Liu, T., Z. Wang, J. Guo, and J. Wang. 2019. “Shear strength of dry joints in precast UHPC segmental bridges: Experimental and theoretical research.” J. Bridge Eng. 24 (1): 04018100. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001323.
Munoz, M. A. C., D. K. Harris, T. M. Ahlborn, and D. C. Froster. 2014. “Bond performance between ultrahigh-performance concrete and normal-strength concrete.” J. Mater. Civ. Eng. 26 (8): 04014031. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000890.
Roberts, C. L., J. E. Breen, and M. E. Kreger. 1993. Measurement based revisions for segmental bridge design criteria. Rep. No. 1234-3F. Austin, TX: Center for Transportation Research, Univ. of Texas at Austin.
Russell, H. G., and B. A. Graybeal. 2013. Ultra-high performance concrete: A state-of-the-art report for the bridge community. Washington, DC: FHWA.
Semendary, A. A., and D. Svecova. 2021. “Bond characterization and interfacial coefficients at precast UHPC and cast-in-place UHPC interface.” J. Mater. Civ. Eng. 33 (7): 04021143. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003755.
SIA (Swiss Society of Engineers and Architects). 2016. Ultra-high performance fiber reinforced concrete (UHPFRC) materials, design and execution (final draft). Zurich, Switzerland: SIA.
Tong, T., S. Yuan, J. Wang, and Z. Liu. 2021. “The role of bond strength in structural behaviors of UHPC-NC composite beams: Experimental investigation and finite element modeling.” Comp. Struct. 255 (1): 112914. https://doi.org/10.1016/j.compstruct.2020.112914.
Voo, Y. L., S. J. Foster, and C. C. Voo. 2015. “Ultrahigh-performance concrete segmental bridge technology: Toward sustainable bridge construction.” J. Bridge Eng. 20 (8): B5014001. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000704.
Xue, J. Q., B. Briseghella, F. Y. Huang, C. Nuti, H. Tabatabai, and B. Chen. 2020. “Review of ultra-high performance concrete and its application in bridge engineering.” Constr. Build. Mater. 260 (Nov): 119844. https://doi.org/10.1016/j.conbuildmat.2020.119844.
Yoo, D.-Y., J.-J. Kim, and J.-J. Park. 2019. “Effect of fiber spacing on dynamic pullout behavior of multiple straight steel fibers in ultra-high-performance concrete.” Constr. Build. Mater. 210 (Jun): 461–472. https://doi.org/10.1016/j.conbuildmat.2019.03.171.
Yoo, D.-Y., J.-H. Lee, and Y.-S. Yoon. 2013. “Effect of fiber content on mechanical and fracture properties of ultra high performance fibre reinforced cementitious composites.” Compos. Struct. 106 (Dec): 742–753. https://doi.org/10.1016/j.compstruct.2013.07.033.
Zhang, C., X. Shao, and Y. Zhang. 2015. “Joint design and model test of extra-long-span continuous box girder composed of UHPC.” Chin. Civ. Eng. J. 48 (4): 52–58. https://doi.org/10.15951/j.tmgcxb.2015.04.009.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Aug 16, 2021
Accepted: Nov 22, 2021
Published online: Apr 28, 2022
Published in print: Jul 1, 2022
Discussion open until: Sep 28, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Scott Muzenski, Zachary B. Haber, Benjamin Graybeal, Monolithic and non-monolithic interface shear performance of ultra-high performance concrete, Engineering Structures, 10.1016/j.engstruct.2023.115667, 281, (115667), (2023).
- Wenbiao Sun, Wei Fan, Jie Yang, Yang Zhang, Zhengwu Zhong, Interfacial shear performance of UHPC-strengthened RC structures using post-installed rebar connections: Experiments and analyses, Engineering Structures, 10.1016/j.engstruct.2022.115411, 277, (115411), (2023).
- Zheng Feng, Chuanxi Li, Lu Ke, Doo-Yeol Yoo, Tensile behavior of ultra-high-performance fiber-reinforced concrete (UHPFRC) structure with cold joints, Engineering Structures, 10.1016/j.engstruct.2022.115084, 273, (115084), (2022).