Effect of the Glass Transition Temperature of Acrylic Polymers on Physical and Mechanical Properties of Kaolinite Clay and Sandy Soil
Publication: Journal of Materials in Civil Engineering
Volume 33, Issue 5
Abstract
The physical and mechanical behavior of soil polymer composites tightly depends on the properties and structures of both soil and polymer. This study aims to investigate the effect of glass transition temperature as one of the most important characteristics of adhesive resins of acrylic polymers on the geotechnical behavior of soils that have not been fully covered by previous studies. To achieve that, three similar copolymers of methyl methacrylate-co-butyl acrylate with different glass-transition temperatures of 1°C, 33°C, and 51°C were synthesized, and two representative specimens of cohesive (kaolinite clay) and noncohesive (sand) soils were chosen to perform a full investigation of the consequential changes in the physical and mechanical behavior. A series of laboratory tests, including the Atterberg limits tests, the unconfined compressive strength tests, direct shear tests in soaked and unsoaked conditions, swelling tests, and odometer tests, were conducted on untreated and treated soils with synthesized polymers. The results showed a salient enhancement in the cohesion and the unconfined compressive strength value of both soils. However, the polymer with a glass-transition temperature near to ambient temperature led to a greater increase in the compressive and shear strength of stabilized soil among its peers. Samples treated with the polymer having the lowest glass transition temperature revealed a more compression index (i.e., obtained from odometer tests) and lower unconfined compressive strength. It is also observed that the swelling index and swelling pressure decreased marginally with increasing the glass transition temperature.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
References
Al-Khanbashi, A., and S. W. Abdalla. 2006. “Evaluation of three waterborne polymers as stabilizers for sandy soil.” Geotech. Geol. Eng. 24 (6): 1603–1625. https://doi.org/10.1007/s10706-005-4895-3.
Allahverdi, A., and E. N. Kani. 2013. “Use of construction and demolition waste (CDW) for alkali-activated or geopolymer cements.” In Handbook of recycled concrete and demolition waste, 439–475. Amsterdam, Netherlands: Elsevier.
Anderson, C. D., and E. S. Daniels. 2000. Emulsion polymerisation and applications of latex. Shropshire, UK: Rapra Technology.
Arulrajah, A., M. Yaghoubi, M. M. Disfani, S. Horpibulsuk, M. W. Bo, and M. Leong. 2018. “Evaluation of fly ash- and slag-based geopolymers for the improvement of a soft marine clay by deep soil mixing.” Soils Found. 58 (6): 1358–1370. https://doi.org/10.1016/j.sandf.2018.07.005.
ASTM. 2011a. Standard test method for direct shear test of soils under consolidated drained conditions. ASTM D3080. West Conshohocken, PA: ASTM.
ASTM. 2011b. Standard test methods for one-dimensional consolidation properties of soils using incremental loading. ASTM D2435. West Conshohocken, PA: ASTM.
ASTM. 2012. Standard test methods for laboratory compaction characteristics of soil using standard effort [ ()]. ASTM D698. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard test methods for one-dimensional swell or collapse of soils. ASTM D4546. West Conshohocken, PA: ASTM.
ASTM. 2017a. Standard test method for consolidated undrained direct simple shear testing of fine grain soils. ASTM D6528. West Conshohocken, PA: ASTM.
ASTM. 2017b. Standard test methods for liquid limit, plastic limit, and plasticity index of soils. ASTM D4318. West Conshohocken, PA: ASTM.
ASTM. 2017c. Standard test method for particle-size distribution (gradation) of fine-grained soils using the sedimentation (hydrometer) analysis. ASTM D7928. West Conshohocken, PA: ASTM.
ASTM. 2017d. Standard test methods for particle-size distribution (gradation) of soils using sieve analysis. ASTM D6913M. West Conshohocken, PA: ASTM.
Bahranifard, Z., F. Farshchi, and A. Reza. 2019. “An investigation on the effect of styrene-butyl acrylate copolymer latex to improve the properties of polymer modified concrete.” Constr. Build. Mater. 205 (Apr): 175–185. https://doi.org/10.1016/j.conbuildmat.2019.01.175.
Baker, G. L., E. B. Vogel, and M. R. Smith. 2008. “Glass transitions in polylactides.” Polym. Rev. 48 (1): 64–84. https://doi.org/10.1080/15583720701834208.
Bolander, P. 1999. “Laboratory testing of nontraditional additives for stabilization of roads and trail surfaces.” Transp. Res. Rec. 1652 (1): 24–31. https://doi.org/10.3141/1652-38.
Brandon, T. L., J. J. Brown, W. L. Daniels, T. L. DeFazio, G. M. Filz, J. K. Mitchell, J. Musselman, and C. Forsha. 2009. Rapid stabilization/polymerization of wet clay soils: Literature review. AFRL-RX-TY-TP-2009-4601. Blacksburg, VA: Virginia Polytechnic Institute and State Univ.
Cameron, D., C. Hopkins, and M. Rahman. 2016. “Hydrophobic polymer additive for stabilization of aggregates in local government roads.” Procedia Eng. 143: 26–33. https://doi.org/10.1016/j.proeng.2016.06.004.
Chen, F. M. 2016. “The effect of polymers for soil stabilization and soil nutrient retention.” Int. J. Appl. Sci. Res. Rev. 3 (5): 1–6. https://doi.org/10.21767/2349-7238.100049.
Degirmenci, N., A. Okucu, and A. Turabi. 2007. “Application of phosphogypsum in soil stabilization.” Build. Environ. 42 (9): 3393–3398. https://doi.org/10.1016/j.buildenv.2006.08.010.
Du, Y. J., B. W. Yu, K. Liu, N. J. Jiang, and M. D. Liu. 2017. “Physical, hydraulic, and mechanical properties of clayey soil stabilized by lightweight alkali-activated slag geopolymer.” J. Mater. Civ. Eng. 29 (2): 04016217. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001743.
Elaissari, A. 2003. Colloidal polymers, synthesis and characterization: Colloidal polymers. New York: Marcel Dekker.
Estabragh, A. 2011. “Effect of resin on the strength of soil-cement mixture.” J. Mater. Civ. Eng. 23 (7): 969–976. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000252.
Farzi, G. A., and M. Mortezaei. 2016. “Acrylic latexes prepared via miniemulsion polymerization technique for improvement of soil behavior.” J. Nanosci. Technol. 2 (1): 50–54.
Fox, T. G. 1956. “Influence of diluent and of copolymer composition on the glass temperature of a polymer system.” Bull. Am. Phys. Soc. 1: 123.
Ghasemzadeh, H., A. Mehrpajouh, M. Pishvaei, and M. Mirzababaei. 2020. “Effects of curing method and glass transition temperature on the unconfined compressive strength of acrylic liquid polymer-stabilized kaolinite.” J. Mater. Civ. Eng. 32 (8): 04020212. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003287.
Ghasemzadeh, H., and F. Modiri. 2020. “Application of novel Persian gum hydrocolloid in soil stabilization.” Carbohydr. Polym. 246 (Oct): 116639. https://doi.org/10.1016/j.carbpol.2020.116639.
Ghasemzadeh, H., M. Sanaye Pasand, and M. M. Mollanouri Shamsi. 2018. “Experimental study of sulfuric acid effects on hydro-mechanical properties of oxide copper heap soils.” Miner. Eng. 117 (Mar): 100–107. https://doi.org/10.1016/j.mineng.2017.12.010.
Ghasemzadeh, H., and M. Tabaiyan. 2017. “The effect of diesel fuel pollution on the efficiency of soil stabilization method.” Geotech. Geol. Eng. 35 (1): 475–484. https://doi.org/10.1007/s10706-016-0121-8.
Gong, S., H. Chen, X. Zhou, and S. Gunasekaran. 2017. “Synthesis and applications of MANs/poly(MMA-co-BA) nanocomposite latex by miniemulsion polymerization.” R. Soc. Open Sci. 4 (11): 170844. https://doi.org/10.1098/rsos.170844.
Green, V. S., and D. E. Stott. 1999. “Polyacrylamide: A review of the use, effectiveness, and cost of a soil erosion control amendment.” In Proc., 10th Int. Soil Conservation Organization Meeting, 384–389. West Lafayette, IN: Purdue Univ.
Inyang, H. I., S. Bae, G. Mbamalu, and S. W. Park. 2007. “Aqueous polymer effects on volumetric swelling of Na-montmorillonite.” J. Mater. Civ. Eng. 19 (1): 84–90. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:1(84).
Iyengar, S. R., E. Masad, A. K. Rodriguez, H. S. Bazzi, D. Little, and H. J. M. Hanley. 2013. “Pavement subgrade stabilization using polymers: Characterization and performance.” J. Mater. Civ. Eng. 25 (4): 472–483. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000612.
Kang, X., B. Bate, R. P. Chen, W. Yang, and F. Wang. 2019. “Physicochemical and mechanical properties of polymer-amended kaolinite and fly ash-kaolinite mixtures.” J. Mater. Civ. Eng. 31 (6): 04019064. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002705.
Karim, H., and K. Al-Soudany. 2018. “Improving geotechnical properties of clayey soil using polymer material.” In Vol. 162 of Proc., 3rd Int. Conf. Buildings, Construction and Environmental Engineering, 1–6. Spain: Scimago Institutions Rankings. https://doi.org/10.1051/matecconf/201816201002.
Kolay, P. K., B. Dhakal, S. Kumar, and V. K. Puri. 2016. “Effect of liquid acrylic polymer on geotechnical properties of fine-grained soils.” Int. J. Geosynthetics Ground Eng. 2 (4): 29. https://doi.org/10.1007/s40891-016-0071-5.
Kushwaha, P., A. S. Chauhan, S. Swami, and B. L. Swami. 2019. “Investigating the effects of nanochemical-based ionic stabilizer and co-polymer on soil properties for pavement construction.” Int. J. Geotech. Eng. 1–10. https://doi.org/10.1080/19386362.2019.1635817.
Lisbona, A., I. Vegas, J. Ainchil, and C. Ríos. 2012. “Soil stabilization with calcined paper sludge: Laboratory and field tests.” J. Mater. Civ. Eng. 24 (6): 666–673. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000437.
Mirzababaei, M., A. Arulrajah, S. Horpibulsuk, A. Soltani, and N. Khayat. 2018. “Stabilization of soft clay using short fibers and poly vinyl alcohol.” Geotext. Geomembr. 46 (5): 646–655. https://doi.org/10.1016/j.geotexmem.2018.05.001.
Mirzababaei, M., A. Arulrajah, and M. Ouston. 2017. “Polymers for stabilization of soft clay soils.” Procedia Eng. 189: 25–32. https://doi.org/10.1016/j.proeng.2017.05.005.
Mohammed, A. S., and C. Vipulanandan. 2014. “Compressive and tensile behavior of polymer treated sulfate contaminated CL soil.” Geotech. Geol. Eng. 32 (1): 71–83. https://doi.org/10.1007/s10706-013-9692-9.
Monual, S., and H. Singh. 2005. “Acrylic monomers based emulsion copolymer for coating application.” Indian J. Fibre Text. Res. 30 (2): 184–189.
Naeini, S. A., B. Naderinia, and E. Izadi. 2012. “Unconfined compressive strength of clayey soils stabilized with waterborne polymer.” KSCE J. Civ. Eng. 16 (6): 943–949. https://doi.org/10.1007/s12205-012-1388-9.
Nairn, J. A. 2007. Polymer structure and characterization. London: Royal Society of Chemistry.
Newman, K., and J. S. Tingle. 2004. “Emulsion polymers for soil stabilization.” In Proc., FAA Worldwide Airport Technology Transfer Conf. Washington, DC: Federal Aviation Administration.
Nicholson, J. W. 2006. The chemistry of polymers. London: Royal Society of Chemistry.
Nielsen, E. L., and R. F. Landel. 1993. Mechanical properties of polymers and composites. Boca Raton, FL: CRC Press.
Orts, W. J., A. Roa-Espinosa, R. E. Sojka, G. M. Glenn, S. H. Imam, K. Erlacher, and J. S. Pedersen. 2007. “Use of synthetic polymers and biopolymers for soil stabilization in agricultural, construction, and military applications.” J. Mater. Civ. Eng. 19 (1): 58–66. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:1(58).
Pei, M., Y. Wu, W. Kim, W. Hyung, and Y. Soh. 2004. “Effect of the monomer ratio on the properties of poly (methyl methacrylate butyl acrylate) latex-modified mortars.” J. Appl. Polym. Sci. 93 (5): 2403–2409.
Pethrick, R. A. 2007. Polymer structure characterization: From nano to macro organization. Cambridge, UK: Royal Society of Chemistry Publishing.
Pishvaei, M., and F. F. Tabrizi. 2010. “Synthesis of high solid content polyacrylate/nanosilica latexes via miniemulsion polymerization.” Iran. Polym. J. 19 (9): 707–716.
Poh, H. Y., G. S. Ghataora, and N. Ghazireh. 2006. “Soil stabilization using basic oxygen steel slag fines.” J. Mater. Civ. Eng. 18 (2): 229–240. https://doi.org/10.1061/(ASCE)0899-1561(2006)18:2(229).
Rahimi, E., K. Oraee, Z. A. S. Tonkaboni, and H. Ghasemzadeh. 2015a. “Considering environmental costs of copper production in cut-off grades optimization.” Arab. J. Geosci. 8 (9): 7109–7123. https://doi.org/10.1007/s12517-014-1646-x.
Rahimi, E., K. Oraee, Z. A. S. Tonkaboni, and H. Ghasemzadeh. 2015b. “Determining the optimum cut-off grades in sulfide copper deposits.” Arch. Min. Sci. 60 (1): 313–328. https://doi.org/10.1515/amsc-2015-0021.
Rauch, A. F., J. S. Harmon, L. E. Katz, and H. M. Liljestrand. 2002. “Liquid soil stabilizers: Measured effects on engineering properties of clay.” Transp. Res. Rec. 1787 (1): 33–41. https://doi.org/10.3141/1787-04.
Renjith, R., D. J. Robert, C. Gunasekara, S. Setunge, and B. O’Donnell. 2020. “Optimization of enzyme-based soil stabilization.” J. Mater. Civ. Eng. 32 (5): 04020091. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003124.
Rezaeimalek, S., J. Huang, and S. Bin-shafique. 2017. “Mixing methods evaluation of a styrene-acrylic based liquid polymer for sand and clay stabilization.” In Proc., Int. Conf. on Transportation Infrastructure and Materials. Qingdao, China: Destech Transactions on Materials Science and Engineering.
Rezaeimalek, S., J. Huang, and S. Bin-shafique. 2018. “Curing method and mix design evaluation of a styrene-acrylic based liquid polymer for sand and clay stabilization.” J. Mater. Civ. Eng. 30 (9): 04018200. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002396.
Rodriguez, A. K., C. Ayyavu, S. R. Iyengar, H. S. Bazzi, E. Masad, D. Little, and H. J. M. Hanley. 2018. “Polyampholyte polymer as a stabiliser for subgrade soil.” Int. J. Pavement Eng. 19 (6): 467–478. https://doi.org/10.1080/10298436.2016.1175561.
Sezer, A., G. Inan, H. R. Yilmaz, and K. Ramyar. 2006. “Utilization of a very high lime fly ash for improvement of Izmir clay.” Build. Environ. 41 (2): 150–155. https://doi.org/10.1016/j.buildenv.2004.12.009.
Sojka, R. E., D. L. Bjorneberg, J. A. Entry, R. D. Lentz, and W. J. Orts. 2007. “Polyacrylamide in agriculture and environmental land management.” Adv. Agron. 92: 75–162.
Steward, P. A., J. Hearn, and M. C. Wilkinson. 2000. “Overview of polymer latex film formation and properties.” Adv. Colloid Interface Sci. 86 (3): 195–267. https://doi.org/10.1016/S0001-8686(99)00037-8.
Wang, R.-M., S.-R. Zheng, and Y.-P. Zheng. 2011. Polymer matrix composites and technology. Philadelphia: Woodhead.
Wheeler, S. J., and V. Sivakumar. 1995. “An elasto plastic critical state framework for unsaturated soil.” Géotechnique 45 (1): 35–53. https://doi.org/10.1680/geot.1995.45.1.35.
Yaghoubi, M., A. Arulrajah, M. M. Disfani, S. Horpibulsuk, S. Darmawan, and J. Wang. 2019. “Impact of field conditions on the strength development of a geopolymer stabilized marine clay.” Appl. Clay Sci. 167 (Jan): 33–42. https://doi.org/10.1016/j.clay.2018.10.005.
Yaowarat, T., S. Horpibulsuk, A. Arulrajah, M. Mirzababaei, and A. S. A. Rashid. 2018. “Compressive and flexural strength of polyvinyl alcohol-modified pavement concrete using recycled concrete aggregates.” J. Mater. Civ. Eng. 30 (4): 04018046. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002233.
Yin, Z., J. Cao, Z. Li, and D. Qiu. 2016. “Optimizing the interaction between poly(vinyl alcohol) and sandy soil for enhanced water retention performance.” RSC Adv. 6 (16): 13377–13383. https://doi.org/10.1039/C5RA22309A.
Yu, J., Y. Chen, G. Chen, and L. Wang. 2020. “Experimental study of the feasibility of using anhydrous sodium metasilicate as a geopolymer activator for soil stabilization.” Eng. Geol. 264 (Jan): 105316. https://doi.org/10.1016/j.enggeo.2019.105316.
Zaliha, S., S. Zuber, H. Kamarudin, M. Mustafa, A. Bakri, and M. Binhussain. 2013. “Review on soil stabilization techniques.” Aust. J. Basic Appl. Sci. 7 (5): 258–265. https://doi.org/10.1061/%28ASCE%29MT.1943-5533.0002935.
Zheng, C., Q. Yang, and J. Huang. 2019. “Lignin with and without polymerization for soil stabilization.” J. Mater. Civ. Eng. 31 (12): 04019292. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002935.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 33 • Issue 5 • May 2021
Copyright
© 2021 American Society of Civil Engineers.
History
Received: May 18, 2020
Accepted: Sep 1, 2020
Published online: Feb 23, 2021
Published in print: May 1, 2021
Discussion open until: Jul 23, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.