Evaluation of the Effect of UHMWPE on the Low-Temperature Cracking of Hot-Mix Asphalt
Publication: Journal of Materials in Civil Engineering
Volume 33, Issue 3
Abstract
Low-temperature cracking is a very common type of distress in flexible pavements in cold areas that extends in the form of longitudinal and transverse cracks on the surface layer. Modifying the properties of the control asphalt cement to improve its performance at low temperatures is a way to control this type of cracking. The effect of using ultrahigh-molecular-weight polyethylene (UHMWPE) as a polymeric additive was investigated with rheological, mechanical, and thermodynamic tests. Bending beam rheometer (BBR) testing of the asphalt cement at low temperatures and mechanical tests, including pull off (PO) and semicircular bend (SCB), were performed on asphalt mixtures to examine the effect of this additive on the low-temperature cracking potential of hot-mix asphalt. In addition, thermodynamic tests, including asphalt cement and aggregate surface free energy (SFE) using the Wilhelmy plate (WP) and the universal sorption device (USD) methods, were performed to better understand the results. Based on the results of the BBR test, the application of UHMWPE improved the performance of the modified asphalt cement at low temperatures. Also, the results of the SFE test showed that using UHMWPE increased the cohesion and the adhesion free energies. These changes were closely correlated with the results of the PO test in cohesive and adhesive modes, respectively. The results of SCB test for parameters including peak load, fracture energy, and fracture toughness demonstrated that the incorporation of UHMWPE significantly improves the low-temperature properties of the modified asphalt mixture. Moreover, based on the statistical analysis, the SFE parameters had a positive effect on peak load and fracture energy. The results for the fracture energy parameter revealed that, after crack formation, only the cohesion free energy parameter was effective on asphalt concrete resistance until the moment of failure.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
No data, models, or code were generated or used during the study.
References
AASHTO. 2012. Standard method of test for determining the rheological properties of asphalt binder using a dynamic shear rheometer (DSR). AASHTO T 315. Washington, DC: AASHTO.
AASHTO. 2016. Standard method of test for determining asphalt binder bond strength by means of the binder bond strength (BBS) test. AASHTO T 361. Washington, DC: AASHTO.
AASHTO. 2018. Standard method of test for flash point of asphalt binder by cleveland open cup. AASHTO T 48. Washington, DC: AASHTO.
AASHTO. 2019a. Standard method of test for determining the flexural creep stiffness of asphalt binder using the bending beam rheometer (BBR) test. AASHTO T 313. Washington, DC: AASHTO.
AASHTO. 2019b. Standard method of test for determining the fracture energy of asphalt mixtures using the semicircular bend geometry (SCB). AASHTO TP 105. Washington, DC: AASHTO.
Abdelaziz, A., C.-H. Ho, and M. Snyder. 2018. “Evaluating the influence of polymer modified asphalt binders on low temperature properties.” In Proc., MATEC Web of Conf. Les Ulis, France: Édition Diffusion Presse Sciences.
Arabani, M., and G. H. Hamedi. 2010. “Using the surface free energy method to evaluate the effects of polymeric aggregate treatment on moisture damage in hot-mix asphalt.” J. Mater. Civ. Eng. 23 (6): 802–811. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000228.
Ashish, P. K., D. Singh, and R. Jain. 2020. “Evaluating the effect of carbon nanotube on low temperature property of asphalt binder through dissipated energy–based approach.” J. Mater. Civ. Eng. 32 (3): 04019376. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003056.
Asphalt Institute. 2015. Asphalt mix design methods: Manual series. 4th ed. Lexington, KY: Asphalt Institute.
ASTM. 2001. Standard specification for hot-mixed, hot laid bituminous paving mixtures (withdrawn 2009). ASTM D3515. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard test methods for specific gravity of soil solids by water pycnometer. ASTM D854-14. West Conshohocken, PA: ASTM.
ASTM. 2015a. Standard test method for relative density (specific gravity) and absorption of coarse aggregate. ASTM C127-15. West Conshohocken, PA: ASTM.
ASTM. 2015b. Test method for relative density (specific gravity) and absorption of fine aggregate. ASTM C128-15. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard test method for evaluation of asphalt mixture cracking resistance using the semi-circular bend test (SCB) at intermediate temperatures. ASTM D8044. West Conshohocken, PA: ASTM.
ASTM. 2017. Standard test methods for uncompacted void content of fine aggregate (as influenced by particle shape, surface texture, and grading). ASTM C1252-17. West Conshohocken, PA: ASTM.
ASTM. 2018. Standard test method for soundness of aggregates by use of sodium sulfate or magnesium sulfate. ASTM C88/C88M-18. West Conshohocken, PA: ASTM.
ASTM. 2019. Standard test method for flat particles, elongated particles, or flat and elongated particles in coarse aggregate. ASTM D4791. West Conshohocken, PA: ASTM.
ASTM. 2020. Standard test method for resistance to degradation of small-size coarse aggregate by abrasion and impact in the los angeles machine. ASTM C131/C131M-20. West Conshohocken, PA: ASTM.
Baglieri, O., D. Dalmazzo, M. Barazia, H. A. Tabatabaee, and H. U. Bahia. 2012. “Influence of physical hardening on the low-temperature properties of bitumen and asphalt mixtures.” Procedia Soc. Behav. Sci. 53 (Oct): 504–513. https://doi.org/10.1016/j.sbspro.2012.09.901.
Bhasin, A. 2006. “Development of methods to quantify bitumen-aggregate adhesion and loss of adhesion due to water.” Ph.D. thesis, Dept. of Civil Engineering, Texas A&M Univ.
Bhasin, A., and D. N. Little. 2007. “Characterization of aggregate surface energy using the universal sorption device.” J. Mater. Civ. Eng. 19 (8): 634–641. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:8(634).
Bhasin, A., E. Masad, D. Little, and R. Lytton. 2006. “Limits on adhesive bond energy for improved resistance of hot-mix asphalt to moisture damage.” Transp. Res. Rec. 1970 (1): 2–13. https://doi.org/10.1177/0361198106197000101.
Canestrari, F., F. Cardone, A. Graziani, F. A. Santagata, and H. U. Bahia. 2010. “Adhesive and cohesive properties of asphalt-aggregate systems subjected to moisture damage.” Supplement, Road Mater. Pavement Des. 11 (S1): 11–32. https://doi.org/10.1080/14680629.2010.9690325.
Cheng, Y., L. Li, Y. Zhang, Z. Lv, and C. Zhu. 2019. “Quantitative analysis of effect and interaction of diatomite and basalt fiber on asphalt performance.” J. Mater. Civ. Eng. 31 (12): 04019306. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002948.
Du, J., C. Ai, S. An, and Y. Qiu. 2020. “Rheological properties at low temperatures and chemical analysis of a composite asphalt modified with polyphosphoric acid.” J. Mater. Civ. Eng. 32 (5): 04020075. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003123.
Haas, R., and W. Phang. 1988. “Relationships between mix characteristics and low temperature pavement cracking.” Proc. Assoc. Asphalt Paving Technol. 57 (2): 290–303.
Hamedi, G. H., A. Sahraei, and M. R. Esmaeeli. 2018. “Investigate the effect of using polymeric anti-stripping additives on moisture damage of hot mix asphalt.” Eur. J. Environ. Civ. Eng. 1–14. https://doi.org/10.1080/19648189.2018.1517697.
Hefer, A. W., A. Bhasin, and D. N. Little. 2006. “Bitumen surface energy characterization using a contact angle approach.” J. Mater. Civ. Eng. 18 (6): 759–767. https://doi.org/10.1061/(ASCE)0899-1561(2006)18:6(759).
Isacsson, U., and H. Zeng. 1998. “Low-temperature cracking of polymer-modified asphalt.” Mater. Struct. 31 (1): 58–63. https://doi.org/10.1007/BF02486415.
Jia, Y., R.-J. Cao, and B. Li. 2005. Superpave fundamentals reference manual. Beijing: China Communications Publishing and Media Management.
Jiao, Y., L. Zhang, Q. Guo, M. Guo, and Y. Zhang. 2020. “Acoustic emission-based reinforcement evaluation of basalt and steel fibers on low-temperature fracture resistance of asphalt concrete.” J. Mater. Civ. Eng. 32 (5): 04020104. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003118.
Jung, D., and T. S. Vinson. 1994. Low-temperature cracking: Test selection. Washington, DC: Transportation Research Board.
Kurtz, S. M. 2004. The UHMWPE handbook: Ultra-high molecular weight polyethylene in total joint replacement. Amsterdam, Netherlands: Elsevier.
Liang, M., X. Xin, W. Fan, J. Zhang, H. Jiang, and Z. Yao. Forthcoming. “Comparison of rheological properties and compatibility of asphalt modified with various polyethylene.” Int. J. Pavement Eng. 1–10.
Lu, X., U. Isacsson, and J. Ekblad. 2003. “Influence of polymer modification on low temperature behaviour of bituminous binders and mixtures.” Mater. Struct. 36 (10): 652–656. https://doi.org/10.1007/BF02479497.
Mansourkhaki, A., and A. Aghasi. 2019. “Performance of rubberized asphalt containing liquid nanomaterial anti-strip agent.” Constr. Build. Mater. 214 (Jul): 468–474. https://doi.org/10.1016/j.conbuildmat.2019.03.071.
Marasteanu, M., W. Buttlar, H. Bahia, C. Williams, K. H. Moon, E. Z. Teshale, A. C. Falchetto, M. Turos, E. Dave, and G. Paulino. 2012. Investigation of low temperature cracking in asphalt pavements national pooled fund study—Phase II. Minnesota: Univ. of Minnesota.
Mercado, A. 2007. “Influence of fundamental material properties and air void structure on moisture damage of asphalt mixes.” Doctoral dissertation, Dept. of Civil Engineering, Texas A&M Univ.
Nsengiyumva, G., Y.-R. Kim, and T. You. 2015. Development of a semicircular bend (SCB) test method for performance testing of nebraska asphalt mixtures. Lincoln, NE: Nebraska Dept. of Roads.
Qing, Z., L. Qi-Cheng, L. Peng, C. Chuan-Sheng, and K. Jiang-Rong. 2018. “Study on modification mechanism of nano-ZnO/polymerised styrene butadiene composite-modified asphalt using density functional theory.” Road Mater. Pavement Des. 21 (5): 1426–1438.
Singh, D., and S. Girimath. 2016. “Influence of RAP sources and proportions on fracture and low temperature cracking performance of polymer modified binder.” Constr. Build. Mater. 120 (9): 10–18. https://doi.org/10.1016/j.conbuildmat.2016.05.094.
Stein, H. L. 1988. “Ultra high molecular weight polyethylene (UHMWPE).” In Vol. 2 of Engineering materials handbook, 167–171. Novelty, OH: ASM International.
Sun, L., X. Xin, and J. Ren. 2017. “Asphalt modification using nano-materials and polymers composite considering high and low temperature performance.” Constr. Build. Mater. 133 (Feb): 358–366. https://doi.org/10.1016/j.conbuildmat.2016.12.073.
Sun, M., Y. Bi, M. Zheng, J. Wang, and L. Wang. 2020. “Performance of polyurethane mixtures with skeleton-interlocking structure.” J. Mater. Civ. Eng. 32 (2): 04019358. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003015.
Teltayev, B., C. Rossi, G. Izmailova, E. Amirbayev, and A. Elshibayev. 2019. “Evaluating the effect of asphalt binder modification on the low-temperature cracking resistance of hot mix asphalt.” Case Stud. Constr. Mater. 11 (Dec): e00238. https://doi.org/10.1016/j.cscm.2019.e00238.
Van Oss, C. J., M. K. Chaudhury, and R. J. Good. 1988. “Interfacial Lifshitz–van der Waals and polar interactions in macroscopic systems.” Chem. Rev. 88 (6): 927–941. https://doi.org/10.1021/cr00088a006.
Wang, D., A. Cannone Falchetto, C. Riccardi, J. Westerhoff, and M. P. Wistuba. Forthcoming-a. “Investigation on the effect of physical hardening and aging temperature on low-temperature rheological properties of asphalt binder.” Road MateriPavementDes.: 1–23.
Wang, T., J. Wang, X. Hou, and F. Xiao. Forthcoming-b. “Effects of SARA fractions on low temperature properties of asphalt binders.” Road Mater. Pavement Des.: 1–18.
Xu, Y., C. Zheng, Y. Feng, and X. Guo. 2018. “Low-temperature cohesive and adhesive strength testing of contact surface between bitumen and mineral aggregates by image analysis.” Constr. Build. Mater. 183 (9): 95–101. https://doi.org/10.1016/j.conbuildmat.2018.06.169.
Yao, H., Q. Dai, Z. You, M. Ye, and Y. K. Yap. 2016. “Rheological properties, low-temperature cracking resistance, and optical performance of exfoliated graphite nanoplatelets modified asphalt binder.” Constr. Build. Mater. 113 (6): 988–996. https://doi.org/10.1016/j.conbuildmat.2016.03.152.
Yu, J.-Y., H.-L. Zhang, P. Sun, and S.-F. Zhao. 2018. “Laboratory performances of nano-particles/polymer modified asphalt mixtures developed for the region with hot summer and cold winter and field evaluation.” Road Mater. Pavement Des. 21 (6): 1529–1544.
Zhang, H., G. Xu, X. Chen, R. Wang, and K. Shen. 2019. “Effect of long-term laboratory aging on rheological properties and cracking resistance of polymer-modified asphalt binders at intermediate and low temperature range.” Constr. Build. Mater. 226 (Nov): 767–777. https://doi.org/10.1016/j.conbuildmat.2019.07.206.
Zhang, H.-L., M.-M. Su, S.-F. Zhao, Y.-P. Zhang, and Z.-P. Zhang. 2016. “High and low temperature properties of nano-particles/polymer modified asphalt.” Constr. Build. Mater. 114 (Jul): 323–332. https://doi.org/10.1016/j.conbuildmat.2016.03.118.
Zhu, C., H. Zhang, and Y. Zhang. 2019. “Influence of layered silicate types on physical, rheological and aging properties of SBS modified asphalt with multi-dimensional nanomaterials.” Constr. Build. Mater. 228 (Dec): 116735. https://doi.org/10.1016/j.conbuildmat.2019.116735.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 33 • Issue 3 • March 2021
Copyright
© 2020 American Society of Civil Engineers.
History
Received: May 8, 2020
Accepted: Jul 30, 2020
Published online: Dec 22, 2020
Published in print: Mar 1, 2021
Discussion open until: May 22, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.