Internal Damping Ratio of Ultrahigh-Performance Fiber-Reinforced Concrete Considering the Effect of Fiber Content and Damage Evolution
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 12
Abstract
This paper reports the characterization of internal damping ratio () and factor of ultrahigh-performance fiber-reinforced concrete (UHPFRC) using acoustic tests for undamaged and damaged samples excited by an impact. Ratio is a nondimensional parameter that measures the material capacity to dissipate vibration, and the factor is physically interpreted as inverse attenuation, measuring the undamped characteristics of an oscillator. A servohydraulic testing machine was used for straining the samples cyclically, and at the end of each cycle the acoustic tests were made to measure and . Furthermore, scanning electron microscopy (SEM) was performed in samples extracted from the damaged specimens. From results, undamaged samples presented average around 0.35% with maximum and minimum values of 0.50% and 0.15%, respectively. The analysis of damaged samples showed that the internal damping gave a small variation in the first two load cycles and achieved 0.8% after the peak stress. Low values of found in the present study suggest that UHPFRC structures are more susceptible to excessive vibrations than normal-strength concrete structures. Moreover, SEM images showed damage mechanisms that are the probable reasons for the increase of after severe loading.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code generated or used during the study are available in a repository online in accordance with funder data retention policies. Furthermore, some or all data, models, or code used during the study were provided by a third party. Direct requests for these materials may be made to the provider as indicated in the “Acknowledgments.”
Acknowledgments
The authors gratefully acknowledge the financial support (Grant Nos. 141993/2014-6 and 142179/2015-9) provided by the Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) from Brazil.
References
AFGC (Association Française de Génie Civil). 2013. Ultra high performance fibre-reinforced concretes recommandations. Paris: AFGC.
Ahlborn, T. M., E. J. Puese, and D. L. Misson. 2008. Ultra-high performance concrete for michigan bridges: Material performance. Phase I: Michigan. Washington, DC: US Dept. of Transportation.
Ali, M., A. Liu, H. Sou, and N. Chouw. 2012. “Mechanical and dynamic properties of coconut fibre reinforced concrete.” Constr. Build. Mater. 30 (May): 814–825. https://doi.org/10.1016/j.conbuildmat.2011.12.068.
ASTM. 2001. Standard test method for dynamic Young’s modulus, shear modulus, and Poisson’s ratio by impulse excitation of vibration. West Conshohocken, PA: ASTM.
ASTM. 2003. Standard test method for fundamental transverse, longitudinal, and torsional resonant frequencies of concrete specimens. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard test method for static modulus of elasticity and Poisson’s ratio of concrete in compression. West Conshohocken, PA: ASTM.
Bachmann, H., et al. 1995. Vibration problems in structures—Practical guidelines. Basel, Switzerland: Birkhäuser.
Boccaccini, D. N., M. Romagnoli, E. Kamseu, P. Veronesi, C. Leonelli, and G. C. Pellacani. 2007. “Determination of thermal shock resistance in refractory materials by ultrasonic pulse velocity measurement.” J. Eur. Ceram. Soc. 27 (2–3): 1859–1863. https://doi.org/10.1016/j.jeurceramsoc.2006.05.070.
Chin, W. J., Y. J. Kim, J. Cho, and J. S. Park. 2012. “Dynamic characteristics evaluation of innovative UHPC pedestrian cable stayed bridge.” Engineering 4 (12): 869–876. https://doi.org/10.4236/eng.2012.412110.
Curadelli, R. O., J. D. Riera, D. Ambrosini, and M. G. Amani. 2008. “Damage detection by means of structural damping identification.” Eng. Struct. 30 (12): 3497–3504. https://doi.org/10.1016/j.engstruct.2008.05.024.
de Graft-Johnson, J. W. S., and N. S. Bawa. 1969. “Effect of mix proportion, water-cement ratio, age and curing conditions on the dynamic modulus of elasticity of concrete.” Build. Sci. 3 (3): 171–177. https://doi.org/10.1016/0007-3628(69)90028-0.
Diamond, S., S. Sahu, and N. Thaulow. 2004. “Reaction products of densified silica fume agglomerates in concrete.” Cem. Concr. Res. 34 (9): 1625–1632. https://doi.org/10.1016/j.cemconres.2004.01.031.
Eiras, J. N., J. S. Popovics, M. V. Borrachero, J. Monzó, and J. Payá. 2015. “The effects of moisture and micro-strucutral modification in drying mortars on vibration-based NDT methods.” Constr. Build. Mater. 94 (Sep): 565–571. https://doi.org/10.1016/j.conbuildmat.2015.07.078.
Fehling, E., M. Schmidt, J. Walraven, T. Leutbecher, and S. Fröhlich. 2014. Ultra-high performance concrete UHPC. Berlin: Ernst & Sohn.
Gheorghiu, C., J. E. Rhazi, and P. Labossiere. 2005. “Impact resonance method for fatigue damage detection in reinforced concrete beams with carbon fibre reinforced polymer.” Can. J. Civ. Eng. 32 (6): 1093–1102. https://doi.org/10.1139/l05-064.
Gidrão, G., P. Krahl, and R. Carrazedo. 2018. “Characterization of concrete internal damping.” In Proc., 3o Encontro Luso-Brasileiro de Degradação em Estruturas de Concreto Armado São Carlos. São Paulo, Brasil: Instituto Brasileiro do Concreto.
Graybeal, B. A. 2007. “Compressive behavior of ultra-high-performance fiber-reinforced concrete.” ACI Mater. J. 104 (2): 146.
Gu, C. P., G. Ye, and W. Sun. 2015. “Ultrahigh performance concrete-properties, applications and perspectives.” Sci. China Technol. Sci. 58 (4): 587–599. https://doi.org/10.1007/s11431-015-5769-4.
Haach, V. G., R. Carrazedo, L. M. F. Oliveira, and M. R. S. Corrêa. 2013. “Application of acoustic tests to mechanical characterization of masonry mortars.” NDT & E Int. 59 (Oct): 18–24. https://doi.org/10.1016/j.ndteint.2013.04.013.
Harlow, J. 2004. Electric power transformer engineering. London: CRC Press.
Jordan, R. W. 1980. “The effect of stress, frequency, curing, mix and age upon the damping of concrete.” Mag. Concr. Res. 32 (113): 195–205. https://doi.org/10.1680/macr.1980.32.113.195.
Khosravani, M. R., and K. Weinberg. 2018. “A review on split Hopkinson bar experiments on the dynamic characterisation of concrete.” Constr. Build. Mater. 190 (Nov): 1264–1283. https://doi.org/10.1016/j.conbuildmat.2018.09.187.
Krahl, P. A., G. de Miranda Saleme Gidrão, and R. Carrazedo. 2018. “Compressive behavior of UHPFRC under quasi-static and seismic strain rates considering the effect of fiber content.” Constr. Build. Mater. 188 (Nov): 633–644. https://doi.org/10.1016/j.conbuildmat.2018.08.121.
Krahl, P. A., G. de Miranda Saleme Gidrão, and R. Carrazedo. 2019. “Cyclic behavior of UHPFRC under compression.” Ceme. Concr. Compos. 104 (Sep): 103363. https://doi.org/10.1016/j.cemconcomp.2019.103363.
Lin, X. 2018. “Numerical simulation of blast responses of ultra-high performance fibre reinforced concrete panels with strain-rate effect.” Constr. Build. Mater. 176 (Jul): 371–382. https://doi.org/10.1016/j.conbuildmat.2018.05.066.
Mehta, P. K., and P. J. M. Monteiro. 2008. Concreto: Estrutura, Propriedades e Materiais. New York: McGraw-Hil.
Meng, W., M. Valipour, and K. H. Khayat. 2017. “Optimization and performance of cost-effective ultra-high performance concrete.” Mater. Struct. 50 (1): 1–29. https://doi.org/10.1617/s11527-016-0896-3.
Ndambi, J.-M., J. Vantomme, and K. Harri. 2002. “Damage assessment in reinforced concrete beams using eigenfrequencies and mode shape derivatives.” Eng. Struct. 24 (4): 501–515. https://doi.org/10.1016/S0141-0296(01)00117-1.
Nguyen, K., B. Freytag, M. Ralbovsky, and O. Rio. 2015. “Assessment of serviceability limit state of vibrations in the UHPFRC-Wild bridge through an updated FEM using vehicle-bridge interaction.” Comput. Struct. 156 (Aug): 29–41. https://doi.org/10.1016/j.compstruc.2015.04.001.
Noushini, A., B. Samali, and K. Vessalas. 2013. “Effect of polyvinyl alcohol (PVA) fibre on dynamic properties of concrete containing fly ash.” In Proc., Composite Construction in Steel and Concrete VII, edited by M. Bradford and B. Uy, 456–467. Reston, VA: ASCE. https://doi.org/10.1061/9780784479735.035.
Othman, H., and H. Marzouk. 2016. “Impact response of ultra-high-performance reinforced concrete plates.” ACI Struct. J. 113 (6): 1325–1334. https://doi.org/10.14359/51689157.
Paultre, P. 2011. Dynamics of structures. London: Wiley.
Pereira, A. H. A., G. M. Fortes, B. Schickle, T. Tonnesen, B. Musolino, C. D. Maciel, and J. A. Rodrigues. 2010. “Correlation between changes in mechanical strength and damping of a high alumina refractory castable progressively damaged by thermal shock.” Ceramica 56 (339): 311–314. https://doi.org/10.1590/S0366-69132010000300016.
Pereira, A. H. A., B. Musolino, C. D. Maciel, and J. A. Rodrigues. 2012. “Algorithm to determine the damping of ceramic materials by the impulse excitation technique ceramic materials by the impulse excitation technique.” Ceramica 58 (346): 229–237. https://doi.org/10.1590/S0366-69132012000200014.
Pereira, A. H. A., L. B. Otani, J. De Anchieta Rodrigues, N. Traon, T. Tonnesen, and R. Telle. 2011. “The influence of nonlinear elasticity on the accuracy of thermal shock damage evaluation by the impulse excitation technique.” Int. Ceramic Rev. 2011 (Jun): 98–102.
Pickett, G. 1945. “Equations for computing elastic constants from flexural and torsional resonant frequencies of vibration of prisms and cylinders.” In Proc., American Society for Testing Materials, 846–866. West Conshohocken, PA: ASTM.
Rebentrost, M., and G. Wight. 2008. “Experience and applications of ultra high performance concrete in Asia.” In Proc., 2nd Int. Symp. On Ultra High Performance Concrete, 19–30. Kassel, Germany: Kassel Univ.
Resplendino, J. 2004. “First recommendations for ultra-high-performance concretes and examples of application.” In Proc., Int. Symp. on Ultra High Performance Concrete, 868. Kassel, Germany: Kassel Univ.
Russel, G. H., and B. A. Graybeal. 2013. Ultra-high performance concrete: A state-of-the-art report for the bridge community. Washington, DC: Federal Highway Administration.
Saleem, M. A. 2011. “Alternatives to steel grid bridge decks.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Florida International Univ.
Salzmann, A. 2002. “Damping characteristics of reinforced and prestressed normal- and high-strength concrete beams.” Ph.D. thesis, School of Engineering, Griffith Univ.
Salzmann, A., S. Fragomeni, and Y. C. Loo. 2003. “The damping analysis of experimental concrete beams under free-vibration.” Adv. Struct. Eng. 6 (1): 53–64. https://doi.org/10.1260/136943303321625739.
Sanchez, F., and C. Ince. 2009. “Microstructure and macroscopic properties of hybrid carbon nanofiber/silica fume cement composites.” Compos. Sci. Technol. 69 (7–8): 1310–1318. https://doi.org/10.1016/j.compscitech.2009.03.006.
Sanchez, F., and K. Sobolev. 2010. “Nanotechnology in concrete—A review.” Constr. Build. Mater. 24 (11): 2060–2071. https://doi.org/10.1016/j.conbuildmat.2010.03.014.
Shi, C., Z. Wu, J. Xiao, D. Wang, Z. Huang, and Z. Fang. 2015. “A review on ultra high performance concrete. Part I: Raw materials and mixture design.” Constr. Build. Mater. 101 (Dec): 741–751. https://doi.org/10.1016/j.conbuildmat.2015.10.088.
Spasojević, A. 2008. “Structural implications of ultra-high performance fibre-reinforced concrete in bridge design.” Ph.D. thesis, Doctoral Program in Structures, École Polytechnique Fédérale de Lausanne.
Swamy, N., and G. Rigby. 1971. “Dynamic properties of hardened paste, mortar and concrete.” Matériaux et Constr. 4 (1): 13–40. https://doi.org/10.1007/BF02473927.
Tian, Y., S. Shi, K. Jia, and S. Hu. 2015. “Mechanical and dynamic properties of high strength concrete modified with lightweight aggregates presaturated polymer emulsion.” Constr. Build. Mater. 93 (Sep): 1151–1156. https://doi.org/10.1016/j.conbuildmat.2015.05.015.
Toledo Filho, R. D., E. A. B. Koenders, S. Formagini, and E. M. R. Fairbairn. 2012. “Performance assessment of ultra high performance fiber reinforced cementitious composites in view of sustainability.” Mater. Des. 2015 (36): 880–888. https://doi.org/10.1016/j.matdes.2011.09.022.
van Mier, J. 2012. Concrete fracture: A multiscale approach. Abingdon, UK: Taylor & Francis.
Warburton, G. B. 1976. The dynamical behaviour of structures. New York: Pergamon Press.
Yoo, D. Y., and N. Banthia. 2017. “Mechanical and structural behaviors of ultra-high-performance fiber-reinforced concrete subjected to impact and blast.” Constr. Build. Mater. 149 (Sep): 416–431. https://doi.org/10.1016/j.conbuildmat.2017.05.136.
Zdeb, T. 2013. “Ultra-high performance concrete—Properties and technology.” Bull. Pol. Acad. Sci. 61 (1): 183–193. https://doi.org/10.2478/bpasts-2013-0017.
Zheng, L., X. Sharon Huo, and Y. Yuan. 2008. “Experimental investigation on dynamic properties of rubberized concrete.” Constr. Build. Mater. 22 (5): 939–947. https://doi.org/10.1016/j.conbuildmat.2007.03.005.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Mar 25, 2019
Accepted: Apr 15, 2020
Published online: Sep 21, 2020
Published in print: Dec 1, 2020
Discussion open until: Feb 21, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.