Concomitantly Controlling Harmful Fumes Generation and Enhancing Mechanical Properties of SBS Modified Asphalt by the Incorporation of MIL-101(Cr) as Modifier
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 8
Abstract
The metal organic framework [MIL-101(Cr)] was used as a second modifier to prepare MIL-101(Cr)-styrene-butadiene styrene (MIL-101(Cr)/SBS) modified asphalt. The influence of MIL-101(Cr) addition and contents on rheological properties and the amount and nature of fumes produced during higher temperature applications of modified asphalt were studied. Dynamic shear rheometer and multistress creep recovery tests revealed that MIL-101(Cr)/SBS modified asphalt exhibited better viscoelasticity, high temperature stability, and rutting resistance relative to pristine SBS modified asphalt. Compared with the pristine SBS modified asphalt, the storage modulus and loss modulus of 0.05% MIL-101(Cr)/SBS modified asphalt at 46°C increased by 100.9% and 88.1%, respectively. GC-MS analysis concluded that the addition of MIL-101(Cr) effectively reduced the generation of harmful fumes (from 26 to 3) in MIL-101(Cr)/SBS modified asphalt; thus, it can significantly reduce environmental pollution. Fluorescence microscopy analysis showed that MIL-101(Cr) was evenly distributed in SBS modified asphalt, whereas TGA tests revealed higher thermal stability of MIL-101(Cr)/SBS modified asphalt than SBS modified asphalt. This study, based on the incorporation of MIL-101(Cr) into SBS modified asphalt that leads to the effective control of harmful fumes production and enhanced thermal stability, could offer significant potential for designing alternative types of asphalt that enable highway and construction industries to adhere to road and environmental agencies standards.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during this study appear in the published article.
Acknowledgments
This work was supported by the Guangxi Natural Science Foundation Fund, China (Grant No. 2018JJA160105) and the National Natural Science Foundation of China (Grant No. 51768007).
References
Al-Qadi, I. L. 2007. Reclaimed asphalt pavement—A literature review. Urbana, IL: Illinois Center for Transportation.
Anupam, K., and J. Christoph. 2013. “Programming MIL-101Cr for selective and enhanced CO2 adsorption at low pressure by postsynthetic amine functionalization.” Dalton Trans. 43 (3): 1338–1347. https://doi.org/10.1039/c3dt52365a.
Bostancioğlu, M., and Ş. Oruç. 2015. “Effect of activated carbon and furan resin on asphalt mixture performance.” Road Mater. Pavement Des. 17 (2): 1–14. https://doi.org/10.1080/14680629.2015.1092465.
Cao, T., S. Wu, Q. Ye, and H. Xu. 2009. “Creep deformation characteristics of modified asphalt and porous asphalt mixture using TPS additive.” Proc SPIE 7375 (Aug): 73756I. https://doi.org/10.1117/12.839381.
Chao, Z., X. Zhou, H. Cao, G. Wang, and Z. Liu. 2014. “Synthesis of porous graphene/activated carbon composite with high packing density and large specific surface area for supercapacitor electrode material.” J. Power Sources 258 (14): 290–296. https://doi.org/10.1016/j.jpowsour.2014.01.056.
Chen, J., and L. Qiu. 2012. “Analysis of the mechanism of aging and regeneration of SBS modified asphalt based on the infrared spectrum.” J. Shenyang Jianzhu Univ. 28 (5): 859–864.
Chinese Standard. 2011. Standard test methods of bitumen and bituminous mixtures for highway engineering. JTG E20. Beijing: People’s Communication Press.
Cui, P. Q., S. P. Wu, Y. Xiao, and H. H. Zhang. 2015. “Experimental study on the reduction of fumes emissions in asphalt by different additives.” Mater. Res. Innovations 19 (S1): S1-158–S151-161. https://doi.org/10.1179/1432891715Z.0000000001395.
Dave, E. V., and C. Hoplin. 2015. “Flexible pavement thermal cracking performance sensitivity to fracture energy variation of asphalt mixtures.” Supplement, Road Mater. Pavement Des. 16 (S1): 423–441. https://doi.org/10.1080/14680629.2015.1029697.
Dong, F., W. Zhao, Y. Zhang, J. Wei, W. Fan, Y. Yu, and W. Zhe. 2014. “Influence of SBS and asphalt on SBS dispersion and the performance of modified asphalt.” Constr. Build. Mater. 62 (Jul): 1–7. https://doi.org/10.1016/j.conbuildmat.2014.03.018.
Férey, G., C. Mellot-Draznieks, C. Serre, F. Millange, J. Dutour, S. Surblé, and I. Margiolaki. 2005. “A chromium terephthalate-based solid with unusually large pore volumes and surface area.” Science 309 (5743): 2040–2042. https://doi.org/10.1126/science.1116275.
Gandomi, A. H., A. H. Alavi, M. R. Mirzahosseini, and F. M. Nejad. 2011. “Nonlinear genetic-based models for prediction of flow number of asphalt mixtures.” J. Mater. Civ. Eng. 23 (3): 248–263. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000154.
He, Z. R., and M. S. Song. 1993. “Elastic behaviors of swollen multiphase networks of SBS and SIS block copolymers.” Rheol. Acta 32 (3): 254–262. https://doi.org/10.1007/BF00434189.
Hill, B., D. Oldham, B. Behnia, E. H. Fini, W. G. Buttlar, and H. Reis. 2018. “Evaluation of low temperature viscoelastic properties and fracture behavior of bio-asphalt mixtures.” Int. J. Pavement Eng. 19 (4): 362–369. https://doi.org/10.1080/10298436.2016.1175563.
Hofko, B., L. Porot, A. F. Cannone, L. Poulikakos, L. Huber, X. Lu, K. Mollenhauer, and H. Grothe. 2018. “FTIR spectral analysis of bituminous binders: Reproducibility and impact of ageing temperature.” Mater. Struct. 51 (2): 45. https://doi.org/10.1617/s11527-018-1170-7.
Hou, D., M. Han, Y. Muhammad, L. Yu, F. Zhang, Y. Yin, S. Duan, and L. Jing. 2018. “Performance evaluation of modified asphalt based trackless tack coat materials.” Constr. Build. Mater. 165 (Mar): 385–394. https://doi.org/10.1016/j.conbuildmat.2017.12.187.
Hu, P., X. Liang, M. Yaseen, X. Sun, Z. Tong, Z. Zhao, and Z. Zhao. 2018. “Preparation of highly-hydrophobic novel N-coordinated UiO-66 (Zr) with dopamine via fast mechano-chemical method for (CHO-/Cl-)-VOCs competitive adsorption in humid environment.” Chem. Eng. J. 332 (Jan): 608–618. https://doi.org/10.1016/j.cej.2017.09.115.
Hu, P., Z. Zhao, X. Sun, Y. Muhammad, J. Li, S. Chen, C. Pang, T. Liao, and Z. Zhao. 2019. “Construction of crystal defect sites in N-coordinated UiO-66 via mechanochemical in-situ N-doping strategy for highly selective adsorption of cationic dyes.” Chem. Eng. J. 356 (Jan): 329–340. https://doi.org/10.1016/j.cej.2018.09.060.
Isloor, A. M., S. S. Shenvi, A. F. Ismail, S. J. Shilton, and A. Al-Ahmad. 2015. “Humic acid based biopolymeric membrane for effective removal of methylene blue and rhodamine B.” Ind. Eng. Chem. Res. 54 (18): 4965–4975. https://doi.org/10.1021/acs.iecr.5b00761.
Jun-yi, C. T. M. 2005. “Research & analysis of asphalt union & separation experiment.” Shanxi Architect. 6: 111–112. https://doi.org/10.13719/j.cnki.cn14-1279/tu.2005.06.071.
Kang, R. H., J. Park, D. Kang, and J. W. Lee. 2018. “Evaluating isotherm models for the prediction of flue gas adsorption equilibrium and dynamics.” Korean J. Chem. Eng. 35 (3): 734–743. https://doi.org/10.1007/s11814-017-0353-1.
Khutia, A., H. U. Rammelberg, T. Schmidt, S. Henninger, and C. Janiak. 2013. “Water sorption cycle measurements on functionalized MIL-101Cr for heat transformation application.” Chem. Mater. 25 (5): 790–798. https://doi.org/10.1021/cm304055k.
Kim, Y. R., and D. N. Little. 2004. “Linear viscoelastic analysis of asphalt mastics.” J. Mater. Civ. Eng. 16 (2): 122–132. https://doi.org/10.1061/(ASCE)0899-1561(2004)16:2(122).
Kök, B. V., and H. Çolak. 2011. “Laboratory comparison of the crumb-rubber and SBS modified bitumen and hot mix asphalt.” Constr. Build. Mater. 25 (8): 3204–3212. https://doi.org/10.1016/j.conbuildmat.2011.03.005.
Lei, B., B. Li, H. Zhang, L. Zhang, and W. Li. 2007. “Synthesis, characterization, and oxygen sensing properties of functionalized Mesoporous SBA-15 and MCM-41 with a covalently linked ruthenium(II) complex.” J. Phys. Chem. C 111 (30): 11291–11301. https://doi.org/10.1021/jp070008w.
Li, J., F. Zhang, Y. Liu, Y. Muhammad, Z. Su, F. Meng, and X. Chen. 2019. “Preparation and properties of soybean bio-asphalt/SBS modified petroleum asphalt.” Constr. Build. Mater. 201 (Mar): 268–277. https://doi.org/10.1016/j.conbuildmat.2018.12.206.
Loeffler, K. W., C. A. Koehler, N. M. Paul, and D. O. De Haan. 2006. “Oligomer formation in evaporating aqueous glyoxal and methyl glyoxal solutions.” Environ. Sci. Technol. 40 (20): 6318. https://doi.org/10.1021/es060810w.
Meizhao, H., L. Jing, M. Yaseen, Y. Yuhua, Y. Jing, Y. Song, and D. Shaochan. 2018. “Studies on the secondary modification of SBS modified asphalt by the application of octadecyl amine grafted graphene nanoplatelets as modifier.” Diamond Relat. Mater. 89 (Oct): 140–150. https://doi.org/10.1016/j.diamond.2018.08.011.
Ming, L., X. Xue, W. Fan, L. Hui, X. Wang, and B. Xing. 2015. “Investigation of the rheological properties and storage stability of CR/SBS modified asphalt.” Constr. Build. Mater. 74 (Jan): 235–240. https://doi.org/10.1016/j.conbuildmat.2014.10.022.
Mizugai, Y., and M. Katayama. 1980. “The fifth overtones of the C-H stretching vibrations and the bond lengths in some heterocyclic compounds.” Chem. Phys. Lett. 73 (2): 240–243. https://doi.org/10.1016/0009-2614(80)80365-4.
Ogunjobi, A. A., E. A. Ademola, and H. A. Sanuth. 2012. “Toxicity and bacterial decolourization of textile dyes.” Electron. J. Environ. Agric. Food Chem. 11 (4): 415–423.
Peng, X., Z. Li, X. Fei, and S. Qian. 2011a. “Mechanism analysis of polymers on suppressing asphalt fumes.” In Proc., Int. Conf. on Computer Distributed Control and Intelligent Environmental Monitoring. New York: IEEE.
Peng, X. Y., S. L. Qian, F. Xiao, P. Zhang, and Z. Y. Li. 2011b. “The experimental study on the road asphalt fumes suppressive effect of SBS and nano calcium carbonate.” Adv. Mater. Res. 233–235 (May): 507–511. https://doi.org/10.4028/www.scientific.net/AMR.233-235.507.
Qin, X., S. Zhu, S. Chen, and K. Deng. 2013. “The mechanism of flame and smoke retardancy of asphalt mortar containing composite flame retardant material.” Constr. Build. Mater. 41 (8): 852–856. https://doi.org/10.1016/j.conbuildmat.2012.12.048.
Rasool, R. T., S. Pan, and S. Wang. 2018. “Thermal analysis on the interactions among asphalt modified with SBS and different degraded tire rubber.” Constr. Build. Mater. 182 (Sep): 134–143. https://doi.org/10.1016/j.conbuildmat.2018.06.104.
Rogge, W. F., L. M. Hildemann, M. A. Mazurek, and G. R. Cass. 2013. “Sources of Fine Organic Aerosol. 7. Hot asphalt roofing tar pot fumes.” Environ. Sci. Technol. 31 (10): 2726–2730. https://doi.org/10.1021/es960525k.
Sathishkumar, P., M. Arulkumar, and T. Palvannan. 2012. “Utilization of agro-industrial waste Jatropha curcas pods as an activated carbon for the adsorption of reactive dye Remazol Brilliant Blue R (RBBR).” J. Cleaner Prod. 22 (1): 67–75. https://doi.org/10.1016/j.jclepro.2011.09.017.
Wang, J., D. M. Lewis, V. Castranova, D. G. Frazer, T. Goldsmith, S. Tomblyn, J. Simpson, S. Stone, A. Afshari, and P. D. Siegel. 2001. “Characterization of asphalt fume composition under simulated road paving conditions by GC/MS and microflow LC/quadrupole time-of-flight MS.” Anal. Chem. 73 (15): 3691–3700. https://doi.org/10.1021/ac010334m.
Xiao, P., A. H. Kang, and L. I. Xue-Feng. 2005. “Cross blend mechanism of SBS modified asphalt based on infrared spectra.” J. Jiangsu Univ. 26 (6): 529–532.
Xin, W. W., and J. Z. Wei. 2012. “Study on influencing factors of asphalt fume releasing and its hazards.” Appl. Mech. Mater. 209–211: 1257–1260. https://doi.org/10.4028/www.scientific.net/AMM.209-211.1257.
Xu, Y., J. Mills-Beale, and Z. You. 2017. “Chemical characterization and oxidative aging of bio-asphalt and its compatibility with petroleum asphalt.” J. Cleaner Prod. 142 (Jan): 1837–1847. https://doi.org/10.1016/j.jclepro.2016.11.100.
Xue-Lian, L. I., L. Yang, Z. C. Zhao, X. M. Zhang, L. Chen, H. U. Yuan, Y. P. Liu, and H. P. Chen. 2014. “Study on comparative of calcium carbonate mineral medicines by infrared spectrum.” Lishizhen Med. Materia Medica Res. 25 (10): 2418–2419.
Yaseen, M., M. Shakirullah, I. Ahmad, A. U. Rahman, F. U. Rahman, M. Usman, and R. Razzaq. 2013. “Simultaneous operation of dibenzothiophene hydrodesulfurization and methanol reforming reactions over Pd promoted alumina based catalysts.” J. Fuel Chem. Technol. 40 (6): 714–720. https://doi.org/10.1016/S1872-5813(12)60027-9.
Yin, Y., Y. Muhammad, X. Zeng, J. Yang, J. Li, S. Yang, Z. Zhao, and S. Subhan. 2018. “Synthesis and properties of octadecylamine-graphene oxide modified highly hydrophobic waterborne polyurethane emulsion.” Prog. Org. Coat. 125 (Dec): 234–241. https://doi.org/10.1016/j.porgcoat.2018.09.005.
Zhang, F., J. Li, M. Yaseen, M. Han, Y. Yin, and S. Yang. 2018a. “Preparation methods and performance of modified asphalt using rubber–plastic alloy and its compounds.” J. Mater. Civ. Eng. 30 (8): 04018163. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002356.
Zhang, F., Y. Muhammad, L. Yu, M. Han, Y. Yin, D. Hou, and L. Jing. 2018b. “Measurement of water resistance of asphalt based on surface free energy analysis using stripping work between asphalt-aggregate system.” Constr. Build. Mater. 176 (Jul): 422–431. https://doi.org/10.1016/j.conbuildmat.2018.05.055.
Zheng, W. R., Z. L. Guo, Z. C. Chen, Q. Yang, and T. Huang. 2012. “S═O homolytic bond dissociation enthalpies in sulfoxides.” Sulfur Rep. 33 (5): 541–559. https://doi.org/10.1080/17415993.2012.714784.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Aug 27, 2019
Accepted: Dec 2, 2019
Published online: May 18, 2020
Published in print: Aug 1, 2020
Discussion open until: Oct 18, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.