Compatible Air Lime Mortars for Historical Tiled Facades: Bond and Mechanical Strength versus Tile–Mortar Interface Microstructure
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 6
Abstract
Exterior old glazed tiled facades have been a very important heritage testimony of Portuguese culture and traditions throughout the years. The adhesion of the mortars to the old tiles is a very important factor in the behavior of the tiled facades. This study performs a mechanical and water behavioral characterization of compatible air lime (AL) mortars with old substrates and tiles and a microstructural characterization of tile/mortar interface to evaluate the bond between the materials. Formulated lime mortars present mechanical strength values that provide compatibility. Compressive strength varies between 0.42 and 0.61 MPa in AL-based mortars and between 1.09 and 1.60 MPa in lime metakaolin (MK) mortars. evolution by EDS analysis provides indications on penetration of lime paste into ceramic biscuit. Higher values result in higher bond strength values.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors acknowledge the FCT—Portuguese Foundation for Science and Technology for its support through the financial support of Ph.D. Scholarship: “Recovery of old tiled facades—Development of compatible mortars and study of adhesion phenomena to tiles” (SFRH/BD/88890/2012) and DB-HERITAGE project (PTDC/EPH-PAT/4684/2014). They also acknowledge the LNEC (National Laboratory for Civil Engineering) by the support to the PRESERVe project and ACRA (Ovar), Lusical and Lena Agregados for providing materials for testing.
References
Andrejkovičová, S., A. Velosa, E. Ferraz, and F. Rocha. 2014. “Influence of clay minerals addition on mechanical properties of air lime–metakaolin mortars.” Constr. Build. Mater. 65 (Aug): 132–139. https://doi.org/10.1016/j.conbuildmat.2014.04.118.
Arizzi, A., and G. Cultrone. 2012. “Air lime-based mortars blended with a pozzolanic additive and different admixtures: A mineralogical, textural and physical-mechanical study.” Constr. Build. Mater. 31 (Jun): 135–143. https://doi.org/10.1016/j.conbuildmat.2011.12.069.
Baker, L. R. 1979. “Some factors affecting the bond strength of brickwork.” In Proc., 5th Int. Brick Masonry Conf., 62–72. Whyteleafe, UK: International Masonry Society.
Botas, S., R. Veiga, and A. Velosa. 2013a. “Adhesion of lime based mortars to old tiles: Moisture content of tiles.” In HMC2013–Historic Mortars Conf. Paisley, Scotland: Univ. of the West of Scotland.
Botas, S., R. Veiga, and A. Velosa. 2013b. “Reapplication mortars for old tiles: Characteristics of tiles and mortars and selection criteria.” Int. J. Archit. Heritage 8 (1): 124–139. https://doi.org/10.1080/15583058.2012.673690.
Botas, S., R. Veiga, and A. Velosa. 2015. “Adhesion of air lime–based mortars to old tiles: Moisture and open porosity influence in tile/mortar interfaces.” J. Mater. Civ. Eng. 27 (5): 04014161. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001108.
Botas, S., R. Veiga, and A. Velosa. 2017. “Bond strength in mortar/ceramic tile interface: Testing procedure and adequacy evaluation.” Mater. Struct. 50 (5): 211. https://doi.org/10.1617/s11527-017-1086-7.
Carasek, H. 1996. “Adhesion of portland cement based mortars to porous substrates: Assessment of intervening factors and contribution to the study of connection mechanism.” [In Portuguese.] Ph.D. thesis, Dept. of Civil Construction, Universidade de São Paulo, Escola Politécnica.
Cardoso, D., A. Gameiro, A. Santos-Silva, P. Faria, R. Vieira, V. Rosário, and A. Velosa. 2013. “Influence of curing conditions in air lime-metakaolin blended mortars: A mineralogical and mechanical study.” In HMC2013–Historic Mortars Conf. Paisley, Scotland: Univ. of the West of Scotland.
Carvalho, J. R. A., P. R. G. Brandão, and J. M. C. Freitas. 2005. “Relationship between the adhesion strength of mortar coating and the penetration profile of binder paste in the ceramic block porosity.” [In Portuguese.] In Proc., 1st Int. Symp. on Mortars Technology, 518–529. São Paulo, Brazil: Associação Brasileira de Argamassa Industrializada.
CEN (European Committee for Standardization). 1998. Tests for mechanical and physical properties of aggregates. 3: Determination of loose bulk density and voids. EN 1097-3. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 1999a. Methods of test for mortar for masonry. 8: Determination of water retentivity of fresh mortar. prEN 1015-8. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 1999b. Methods of test for mortar for masonry. 11: Determination of flexural and compressive strength of hardened mortar. EN 1015-11. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 1999c. Natural stone test methods. Determination of real density, and of total and open porosity. EN 1936. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2002. Methods of test for mortar for masonry. 18: Determination of water absorption coefficient due to capillarity action of hardened mortar. EN 1015-18. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2004. Natural stone test methods: Determination of the dynamic modulus of elasticity (by measuring the fundamental resonance frequancy). EN 14146. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2006. Methos of test for mortar for masonry. 2: Bulk Sampling of mortars and preparation of test mortars. EN 1015-2:1998/A1. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2010. Building lime. 1: Definitions, specifications and conformity criteria. EN 459-1. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2016a. Methods of test for mortar for masonry. 3: Determination of consistence of fresh mortar (by flow table). EN 1015-3:1999/A1:2004/A2. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2016b. Methods of test for mortar for masonry. 12: Determination of adhesive strength of hardened rendering and plastering mortars on substrates. EN 1015-12. Brussels, Belgium: CEN.
Gameiro, A., A. Santos-Silva, V. Rosário, A. Velosa, and P. Faria. 2012. “Lime-metakaolin mortars for historical buildings repair: Study of the hardening reaction.” In Proc., DURATINET Congress. Lisboa, Portugal: Laboratório Nacional de Engenharia Civil.
Grilo, J., A. Santos-Silva, P. Faria, A. Gameiro, R. Veiga, and A. Velosa. 2014. “Mechanical and mineralogical properties of natural hydraulic lime-metakaolin mortars in different curing conditions.” Constr. Build. Mater. 51 (Jan): 287–294. https://doi.org/10.1016/j.conbuildmat.2013.10.045.
Lawrence, S. J., and L. So. 1994. “The influence of some factors on the tensile bond strength of masonry.” In Proc., 10th IB2MAC, 929–938. Calgary, AB, Canada: Masonry Council of Canada.
Li, G., and X. Wu. 2005. “Influence of fly ash and its mean particle size on certain engineering properties of cement composite mortars.” Cem. Concr. Res. 35 (6): 1128–1134. https://doi.org/10.1016/j.cemconres.2004.08.014.
Marrocchino, E., A. N. Fried, A. Koulouris, and C. Vaccaro. 2009. “Micro-chemical/structural characterisation of thin layer masonry: A correlation with engineering performance.” Constr. Build. Mater. 23 (1): 582–594. https://doi.org/10.1016/j.conbuildmat.2007.09.010.
Paes, I. N., E. Bauer, H. Carasek, and E. Pavón. 2014. “Influence of water transportation inside a mortar/block system on bonding resistance behavior.” Revista Ingeniería de Construcción 29 (2): 175–186. https://doi.org/10.4067/S0718-50732014000200004.
Papaioannou, S., R. Argyropoulou, C. Tachos, and N. Markantonis. 2015. “The adhesion properties of mortars in relation with microstructure.” J. Adhes. 91 (7): 505–517. https://doi.org/10.1080/00218464.2014.931228.
RILEM. 1980. Essais recommendés pour mesurer l’alteration des pierres et évaluer l’efficacité des methods de traitment. Paris: RILEM.
Romero, J. V. 2010. “Adherencia al Hormigón de Mortéros de Diferentes Bases Químicas.” Ph.D. thesis, Universidad Politécnica de Madrid, Escuela Técnica Superior de Ingenieros de Caminos Canales y Puertos.
Sébaïbi, Y., R. M. Dheilly, and M. Quéneudec. 2003. “Study of the water-retention capacity of a lime–sand mortar: Influence of the physicochemical characteristics of the lime.” Cem. Concr. Res. 33 (5): 689–696. https://doi.org/10.1016/S0008-8846(02)01038-4.
Shil’tsina, A. D., and V. I. Vereshchagin. 2000. “Ceramic tiles containing diopside and clay raw materials from Khakassia.” Glass Ceram. 57 (3–4): 13–16. https://doi.org/10.1007/BF02681515.
Silva, A. S., P. Adriano, A. Magalhães, J. Pires, A. Carvalho, A. J. Cruz, J. Mirão, and A. Candeias. 2010. “Characterisation of historical mortars from Alentejo’s religious buildings.” Int. J. Archit. Heritage 4 (2): 138–154. https://doi.org/10.1080/15583050903046322.
Sugo, H., A. W. Page, and S. Lawrence. 2000. “Study of bond strength and mortar microstructure developed using masonry cement.” In Proc., 12th Int. Brick/Block Masonry Conf., 1753–1763. Braga, Portugal: Minho Univ.
Sugo, H., A. W. Page, and S. Lawrence. 2001. “The development of mortar/unit bond.” In Proc., 9th Canadian Masonry Symp. Fredericton, NB, Canada: Univ. of New Brunswick.
Sugo, H., A. W. Page, and S. Lawrence. 2007. “Influence of age on masonry bond strength and mortar microstructure.” Can. J. Civ. Eng. 34 (11): 1433–1442. https://doi.org/10.1139/L07-137.
Taha, R., and N. Shrive. 2001. “The use of pozzolans to improve bond and bond strength.” In Proc., 9th Canadian Masonry Symp. Fredericton, NB, Canada: Univ. of New Brunswick.
Tao, J., G. Qiaoling, Z. Wenyuan, L. Xujian, and W. Hwai-Chung. 2017. “Interfacial transition zone of alkali-activated slag concrete.” ACI Mater. J. 114 (3): 347–354. https://doi.org/10.14359/51689473.
Veiga, M., A. Fragata, A. Velosa, A. Magalhães, and G. Margalha. 2010. “Lime-based mortars: Viability for use as substitution renders in historical buildings.” Int. J. Archit. Heritage 4 (2): 177–195. https://doi.org/10.1080/15583050902914678.
Zegardło, B., M. Szeląg, and P. Ogrodnik. 2016. “Ultra-high strength concrete made with recycled aggregate from sanitary ceramic wastes: The method of production and the interfacial transition zone.” Constr. Build. Mater. 122 (Sep): 736–742. https://doi.org/10.1016/j.conbuildmat.2016.06.112.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Oct 20, 2018
Accepted: Sep 11, 2019
Published online: Mar 17, 2020
Published in print: Jun 1, 2020
Discussion open until: Aug 17, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.