Using Polyolefin Fibers with Moderate-Strength Concrete Matrix to Improve Ductility
Publication: Journal of Materials in Civil Engineering
Volume 31, Issue 9
Abstract
Research has shown that polyolefin fiber–reinforced concrete (PFRC) can meet the requirements of standards in terms of the contributions of fiber in structural design. Such results were obtained with fibers embedded in high-performance concrete matrixes. Given that the precracking maximum strength is mainly governed by the matrix properties, a moderate-strength concrete matrix could lead to a reduction in the initial drop of strength after the limit of proportionality. Nevertheless, it was necessary to determine whether residual postcracking behavior would be similar in a poorer matrix. In this study, a moderate-strength concrete matrix with two dosages of polyolefin fibers was produced. The flexural tensile tests showed that it maintained its residual strength and reduced brittleness. All the concrete types tested met the requirements provided in the relevant standards. The study also provides a large comparison with residual strengths found in the literature showing that the contributions of polyolefin fibers were analogous to those cases in which the fibers were embedded in high-performance concrete matrixes. Hence, PFRC is well suited for use in constructive elements designed with low requirements in terms of concrete matrix properties.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the financial support provided by the Ministry of Economy, Industry and Competitiveness of Spain under the Research Fund Project BIA2016-78742-C2-2-R. They also offer their gratitude to SIKA SAU for supplying the polyolefin fibers.
References
Afroughsabet, V., L. Biolzi, and T. Ozbakkaloglu. 2016. “High-performance fiber-reinforced concrete: A review.” J. Mater. Sci. 51 (14): 6517–6551. https://doi.org/10.1007/s10853-016-9917-4.
Alani, A. M., and D. Beckett. 2013. “Mechanical properties of a large scale synthetic fibre reinforced concrete ground slab.” Constr. Build. Mater. 41: 335–344.
Alberti, M. G. 2015. “Polyolefin fibre-reinforced concrete: From material behaviour to numerical and design considerations.” Ph.D. thesis, Dpto. Ingeniería Civil:Construcción, E.T.S. de Ingenieros de Caminos, Canales y Puertos, Technical Univ. Madrid.
Alberti, M. G., A. Enfedaque, and J. C. Gálvez. 2014. “On the mechanical properties and fracture behavior of polyolefin fiber-reinforced self-compacting concrete.” Constr. Build. Mater. 55: 274–288. https://doi.org/10.1016/j.conbuildmat.2014.01.024.
Alberti, M. G., A. Enfedaque, and J. C. Gálvez. 2015. “Comparison between polyolefin fibre reinforced vibrated conventional concrete and self-compacting concrete.” Constr. Build. Mater. 85 (15): 182–194. https://doi.org/10.1016/j.conbuildmat.2015.03.007.
Alberti, M. G., A. Enfedaque, and J. C. Gálvez. 2016a. “Fracture mechanics of polyolefin fibre reinforced concrete: Study of the influence of the concrete properties, casting procedures, the fibre length and specimen size.” Eng. Fract. Mech. 154: 225–244. https://doi.org/10.1016/j.engfracmech.2015.12.032.
Alberti, M. G., A. Enfedaque, and J. C. Gálvez. 2017a. “On the prediction of the orientation factor and fibre distribution of steel and macro-synthetic fibres for fibre-reinforced concrete.” Cem. Concr. Compos. 77: 29–48. https://doi.org/10.1016/j.cemconcomp.2016.11.008.
Alberti, M. G., A. Enfedaque, J. C. Gálvez, and V. Agrawal. 2016b. “Fibre distribution and orientation of macro-synthetic polyolefin fibre reinforced concrete elements.” Constr. Build. Mater. 122: 505–517. https://doi.org/10.1016/j.conbuildmat.2016.06.083.
Alberti, M. G., A. Enfedaque, J. C. Gálvez, and V. Agrawal. 2016c. “Reliability of polyolefin fibre reinforced concrete beyond laboratory sizes and construction procedures.” Compos. Struct. 140 (15): 506–524. https://doi.org/10.1016/j.compstruct.2015.12.068.
Alberti, M. G., A. Enfedaque, J. C. Gálvez, and A. Ferreras. 2016d. “Pull-out behaviour and interface critical parameters of polyolefin fibres embedded in mortar and self-compacting concrete matrixes.” Constr. Build. Mater. 112: 607–622. https://doi.org/10.1016/j.conbuildmat.2016.02.128.
Alberti, M. G., A. Enfedaque, J. C. Gálvez, and L. Pinillos. 2017b. “Structural cast-in-place application of polyolefin fiber-reinforced concrete in a water pipeline supporting elements.” J. Pipeline Syst. Eng. Pract. 8 (4): 05017002. https://doi.org/10.1061/(ASCE)PS.1949-1204.0000274.
ASTM. 2007. Standard test method for flexural performance of fiber reinforced concrete (using beam with third-point loading). ASTM C1609/C1690M. West Conshohocken, PA: ASTM.
Bencardino, F., L. Rizzuti, G. Spadea, and R. N. Swamy. 2010. “Experimental evaluation of fiber reinforced concrete fracture properties.” Compos. Part B Eng. 41 (1): 17–24.
Bencardino, F., L. Rizzuti, G. Spadea, and R. N. Swamy. 2013. “Implications of test methodology on post-cracking and fracture behaviour of steel fibre reinforced concrete.” Composites Part B 46: 31–38. https://doi.org/10.1016/j.compositesb.2012.10.016.
Blanco, A., P. Pujadas, A. De la Fuente, S. Cavalaro, and A. Aguado. 2013. “Application of constitutive models in European codes to RC–FRC.” Constr. Build. Mater. 40: 246–259.
Brandt, A. 2008. “Fibre reinforced cement-based (FRC) composites after over 40 years of development in building and civil engineering.” Compos. Struct. 86 (1–3): 3–9. https://doi.org/10.1016/j.compstruct.2008.03.006.
Buratti, N., Mazzotti, C., and Savoia, M. 2011. “Post-cracking behaviour of steel and macro-synthetic fibre-reinforced concretes.” Constr. Build. Mater. 25 (5): 2713–2722.
CEN (European Committee for Standardization). 2002a. Testing fresh concrete. Part 2: Slump test. EN 12350-2. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2002b. Testing hardened concrete. Part 3: Compressive strength of test specimens. EN 12390-3. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2007. Test method for metallic fibre concrete. Measuring the flexural tensile strength (limit of proportionality (LOP), residual). EN 14651:2005+A1. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2008. Fibres for concrete. Polymer fibres. Definitions, specifications and conformity. EN 14889-2. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2012. Tests for geometrical properties of aggregates. Part 1: Determination of particle size distribution—Sieving method. EN 933-1. Brussels, Belgium: CEN.
CNR (Consiglio Nazionale delle Ricerche—National Research Council). 2006. Guide for the design and construction of fiber-reinforced concrete structures. CNR-DT 204. Roma: Consiglio Nazionale delle Ricerche.
DBV (Deutscher Beton-und Bautechnik). 2001. Technologie des Stahlfaser-betons und Stahlfaserprit. Berlin: German Society for Concrete and Construction Technology.
Di Prisco, M., M. Colombo, and D. Dozio. 2013. “Fibre-reinforced concrete in fib Model Code 2010: Principles, models and test validation.” Struct. Concr. 14 (4): 342–361. https://doi.org/10.1002/suco.201300021.
Dupont, D., and L. Vandewalle. 2005. “Distribution of steel fibres in rectangular sections.” Cem. Concr. Compos. 27 (3): 391–398. https://doi.org/10.1016/j.cemconcomp.2004.03.005.
Ferrara, L., Y. D. Park, and S. P. Shah. 2008. “Correlation among fresh state behavior, fiber dispersion, and toughness properties of SFRCs.” J. Mater. Civ. Eng. 20 (7): 493–501. https://doi.org/10.1061/(ASCE)0899-1561(2008)20:7(493).
fib (Fédération Internationale du Béton/International Federation for Structural Concrete). 2010. fib Model Code, 2010. Paris: fib.
Giaccio, G., J. Tobes, and R. Zerbino. 2008. “Use of small beams to obtain design parameters of fibre reinforced concrete.” Cem. Concr. Compos. 30 (4): 297–306. https://doi.org/10.1016/j.cemconcomp.2007.10.004.
Laranjeira, F., A. Aguado, C. Molins, S. Grünewald, J. Walraven, and S. Cavalaro. 2012. “Framework to predict the orientation of fibers in FRC: A novel philosophy.” Cem. Concr. Res. 42 (6): 752–768. https://doi.org/10.1016/j.cemconres.2012.02.013.
Nawy, E. 2008. Construction engineering handbook. 2nd ed. New York: Taylor & Francis.
Pujadas, P., A. Blanco, S. Cavalaro, and A. Aguado. 2014. “Plastic fibres as the only reinforcement for flat suspended slabs: Experimental investigation and numerical simulation.” Constr. Build. Mater. 57: 92–104. https://doi.org/10.1016/j.conbuildmat.2014.01.082.
RILEM. 2000. “Test and design methods for steel fibre reinforced concrete.” Mater. Struct. 33 (2): 75–81. https://doi.org/10.1007/BF02484159.
RILEM. 2002. Final recommendation of RILEM TC 162-TDF: Test and design methods for steel fibre reinforced concrete sigma-epsilon-design method. Paris: RILEM Publications.
Serna, P., S. Arango, T. Ribeiro, A. M. Núñez, and E. Garcia-Taengua. 2009. “Structural cast-in-place SFRC: Technology, control criteria and recent applications in spain.” Mater. Struct. 42 (9): 1233–1246. https://doi.org/10.1617/s11527-009-9540-9.
Spanish Minister of Public Works. 2008. Spanish structural concrete code. EHE-08. Madrid, Spain: Spanish Minister of Public Works.
Thomas, J. R. A. 2007. “Mechanical properties of steel fiber-reinforced concrete.” J. Mater. Civ. Eng. 19 (5): 385–392. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:5(385).
Torrijos, M. C., B. E. Barragán, and R. L. Zerbino. 2010. “Placing conditions, mesostructural characteristics and post-cracking response of fibre reinforced self-compacting concretes.” Constr. Build. Mater. 24 (6): 1078–1085. https://doi.org/10.1016/j.conbuildmat.2009.11.008.
Yang, J. M., K. H. Min, H. O. Shin, and Y. S. Yoon. 2012. “Effect of steel and synthetic fibers on flexural behavior of high-strength concrete beams reinforced with FRP bars.” Compos. Part B Eng. 43 (3): 1077–1086.
Yin, S., R. Tuladhar, T. Collister, M. Combe, N. Sivakugan, and Z. Deng. 2015. “Post-cracking performance of recycled polypropylene fibre in concrete.” Constr. Build. Mater. 101 (1): 1069–1077.
Zerbino, R., J. M. Tobes, M. E. Bossio, and G. Giaccio. 2012. “On the orientation of fibres in structural members fabricated with self compacting fibre reinforced concrete.” Cem. Concr. Compos. 34 (2): 191–200. https://doi.org/10.1016/j.cemconcomp.2011.09.005.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jun 11, 2018
Accepted: Jan 30, 2019
Published online: Jun 17, 2019
Published in print: Sep 1, 2019
Discussion open until: Nov 17, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.