Performance Evaluation of Modified Cement-Sodium Silicate Grouting Material for Prereinforcing Loose Deposit Tunnels
Publication: Journal of Materials in Civil Engineering
Volume 31, Issue 7
Abstract
In grouting practices for tunneling in loose deposits, the traditional grouting materials often suffer from its disadvantages, such as prolonged gel times, poor stability, an uncontrollable range of diffusion, and large grout consumption. In this study, an organic–inorganic hybrid chemical grouting material based on polymerization of hydrogen double bonds, Ca-C connection and excellent synergistic interactions among cement, polyethylene glycol (PEG) 200, sodium silicate, and polycarboxylate superplasticizer (PS) was prepared with a simple process. Based on percentages of water/cement at 1, PEG200 (2%), sodium silicate (10%), and PS (0.2%), the obtained modified cement-sodium silicate grouting material (C-S-P) forms a three-dimensional network structure and results in a high stability, good pumpability, satisfactory initial compressive strength, and relatively lower permeability performance. The C-S-P was primarily composed of amorphous PEG and crystalline polysilicic composite, and its probable formation mechanism was evaluated. The proposed new grouting material was applied for reinforcing a tunnel in loose deposits, and the results illustrate that the C-S-P turns out excellent grouting performance and mechanical performance, thereby fulfilling the requirements for tunnel rapid excavation in loose deposits. This study presents the methodology for preparing a new grouting material for reinforcing loose deposits.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study was supported by the National Natural Science Foundation of China (No. 51608539) and the China Postdoctoral Science Foundation (Nos. 2016M592451 and 2017T100610). The corresponding author gratefully acknowledges their financial support.
References
Akiyama, M., and S. Kawasaki. 2012. “Novel grout material comprised of calcium phosphate compounds: In vitro evaluation of crystal precipitation and strength reinforcement.” Eng. Geol. 125 (1): 119–128. https://doi.org/10.1016/j.enggeo.2011.11.011.
Asada, M. 2005. “High-density bentonite slurry for seepage barriers.” J. Mater. Civ. Eng. 17 (2): 178–187. https://doi.org/10.1061/(ASCE)0899-1561(2005)17:2(178).
Brookfield Engineering Laboratories, Inc. 2005. Operating manuals. Middleboro, MA: Brookfield Engineering Laboratories.
Celik, F., and H. Canakci. 2015. “An investigation of rheological properties of cement-based grout mixed with rice husk ash (RHA).” Constr. Build. Mater. 91 (8): 187–194. https://doi.org/10.1016/j.conbuildmat.2015.05.025.
Chinese Standard. 2010. Code for design of concrete structures. GB 50010-2010, 2011. Beijing: Ministry of Housing and Urban-rural Development of the People’s Republic of China.
Cui, W., J. Huang, H. Song, and M. Xiao. 2017. “Development of two new anti-washout grouting materials using multi-way ANOVA in conjunction with grey relational analysis.” Constr. Build. Mater. 156 (12): 184–198. https://doi.org/10.1016/j.conbuildmat.2017.08.126.
Deev, E. V., I. D. Zolnikov, S. V. Goltsova, G. G. Rusanov, and A. A. Emanov. 2013. “Traces of paleoearthquakes in the quaternary deposits of intermontane basins in central Gorny Altai.” Russ. Geol. Geophys. 54 (3): 312–323. https://doi.org/10.1016/j.rgg.2013.02.006.
García, M., C. Pastén, S. A. Sepúlveda, and G. A. Montalva. 2018. “Dynamic numerical investigation of a stepped-planar rockslide in the central Andes.” Eng. Geol. 237 (4): 64–75. https://doi.org/10.1016/j.enggeo.2018.02.001.
Grimm, D., and W. C. P. Paris. 1985. “Foam grout saves tunnel.” Civ. Eng. 55 (9): 64–66.
Hakansson, U., L. Hassler, and H. Stille. 1992. “Rheological properties of microfine cement grouts.” Tunnelling Underground Space Technol. 7 (4): 453–458. https://doi.org/10.1016/0886-7798(92)90076-T.
Hisatake, M., and S. Ohno. 2008. “Effects of pipe roof supports and the excavation method on the displacements above a tunnel face.” Tunnelling Underground Space Technol. 23 (2): 120–127. https://doi.org/10.1016/j.tust.2007.02.002.
Jeng, F. S., M. C. Weng, T. H. Huang, and M. L. Lin. 2002. “Deformational characteristics of weak sandstone and impact to tunnel deformation.” Tunnelling Underground Space Technol. 17 (3): 263–274. https://doi.org/10.1016/S0886-7798(02)00011-1.
Lee, Y. Z., and W. Schubert. 2008. “Determination of the round length for tunnel excavation in weak rock.” Tunnelling Underground Space Technol. 23 (3): 221–231. https://doi.org/10.1016/j.tust.2007.04.001.
Li, S., F. Sha, R. Liu, W. Li, Z. Li, and G. Wang. 2017a. “Properties of cement-based grouts with high amounts of ground granulated blast-furnace slag and fly ash.” J. Mater. Civ. Eng. 29 (11): 1–6. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002083.
Li, S., F. Sha, R. Liu, Q. Zhang, and Z. F. Li. 2017b. “Investigation on fundamental properties of microfine cement and cement-slag grouts.” Constr. Build. Mater. 153 (10): 965–974. https://doi.org/10.1016/j.conbuildmat.2017.05.188.
Li, Z. L., X. H. Wang, and L. Z. Xie. 2012. “Testing and applied research on grouting materials on karst tunnel water inrush.” Electron. J. Geotech. Eng. 17 (5): 2933–2942.
Liao, H. J., R. H. Borden, and R. J. Krizek. 2010. “Microfine cement/sodium silicate grout.” In Grouting, soil improvement and geosynthetics, 676–687. Reston, VA: ASCE.
NHRI (Nanjing Hydraulic Research Institute). 2002. Test code for hydraulic concrete. DL/T5150-2001. Beijing: NHRI.
Rahman, M., J. Wiklund, R. Kotzé, and U. Håkansson. 2017. “Yield stress of cement grouts.” Tunnelling Underground Space Technol. 61 (1): 50–60. https://doi.org/10.1016/j.tust.2016.09.009.
Rotonda, T., P. Tommasi, and D. Boldini. 2010. “Geomechanical characterization of the volcaniclastic material involved in the 2002 landslides at Stromboli.” J. Geotech. Geoenviron. Eng. 136 (2): 389–401. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000218.
Saak, A. W., H. M. Jennings, and S. P. Shah. 2001. “The influence of wall slip on yield stress and viscoelastic measurements of cement pastes.” Cem. Concr. Res. 31 (2): 205–212. https://doi.org/10.1016/S0008-8846(00)00440-3.
SAC (Standardization Administration of the People’s Republic of China). 2001. Methods for testing uniformity of concrete admixture. GB 8077-2000. Beijing: SAC.
Saito, J., Y. Watanabe, T. Yamada, and J. Lee. 2012. “Verification of long-term durability of chemical grout employed as countermeasure against liquefaction.” In Proc., Int. Conf. on Grouting and Deep Mixing, 2024–2033. Hawthorne, NJ: Deep Foundations Institute.
Sedighi, P., H. F. Schweiger, and W. J. Wehr. 2016. “Effect of jet-grout columns on the seismic response of layered soil deposits.” Int. J. Geomech. 17 (3): 1–13. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000771.
Sermon, P. A., M. S. W. Vong, N. J. Bazin, R. Badheka, and D. M. Spriggs. 1995. “Recent developments in silica sol-gel antireflection (AR) coatings.” In Vol. 2633 of Proc., Solid State Lasers for Application to Inertial Confinement Fusion (ICF), 464–474. Bellingham, WA: International Society of Optical Engineering.
Shahrour, I., F. Khoshnoudian, M. Sadek, and H. Mroueh. 2010. “Elastoplastic analysis of the seismic response of tunnels in soft soils.” Tunnelling Underground Space Technol. 25 (4): 478–482. https://doi.org/10.1016/j.tust.2010.01.006.
Sharifzadeh, M., A. Tarifard, and M. A. Moridi. 2013. “Time-dependent behavior of tunnel lining in weak rock mass based on displacement back analysis method.” Tunnelling Underground Space Technol. 38 (9): 348–356. https://doi.org/10.1016/j.tust.2013.07.014.
Suganya, K., and P. V. Sivapullaiah. 2016. “Role of sodium silicate additive in cement-treated Kuttanad soil.” J. Mater. Civ. Eng. 28 (6): 1–6. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001538.
Vong, M. S. W., N. Bazin, and P. A. Sermon. 1997. “Chemical modification of silica gels.” J. Sol-Gel. Sci. Technol. 8 (1–3): 499–505. https://doi.org/10.1023/A:1018350227105.
Wang, Z. F., S. L. Shen, C. E. Ho, and Y. H. Y. Kim. 2013. “Investigation of field-installation effects of horizontal twin-jet grouting in Shanghai soft soil deposits.” Can. Geotech. J. 50 (3): 288–297. https://doi.org/10.1139/cgj-2012-0199.
Wang, Z. F., R. C. K. Wong, S. Li, and L. Qiao. 2012. “Finite element analysis of long-term surface settlement above a shallow tunnel in soft ground.” Tunnelling Underground Space Technol. 30 (4): 85–92. https://doi.org/10.1016/j.tust.2012.02.010.
Wei, T., D. Zhang, and L. Chen. 2015. “The kinetics study and reaction mechanism of acrylate grouting materials.” Bulg. Chem. Commun. 47: 89–92.
Weng, M. C., L. S. Tsai, C. Y. Liao, and F. S. Jeng. 2010. “Numerical modeling of tunnel excavation in weak sandstone using a time-dependent anisotropic degradation model.” Tunnelling Underground Space Technol. 25 (4): 397–406. https://doi.org/10.1016/j.tust.2010.02.004.
Xiao, J. Z., F. C. Dai, Y. Q. Wei, H. Min, C. Xu, and X. B. Tu. 2014. “Cracking mechanism of secondary lining for a shallow and asymmetrically-loaded tunnel in loose deposits.” Tunnelling Underground Space Technol. 43 (7): 232–240. https://doi.org/10.1016/j.tust.2014.05.013.
Yang, P., Z. B. Peng, Y. Q. Tang, W. X. Peng, and Z. M. He. 2008. “Penetration grouting reinforcement of sandy gravel.” J. Cent. South. Univ. 15 (2): 280–284. https://doi.org/10.1007/s11771-008-0052-5.
Yoo, C., and H. K. Shin. 2003. “Deformation behaviour of tunnel face reinforced with longitudinal pipes-laboratory and numerical investigation.” Tunnelling Underground Space Technol. 18 (4): 303–319. https://doi.org/10.1016/S0886-7798(02)00101-3.
Yoshioka, K., E. Sakai, M. Daimon, and A. Kitahara. 2010. “Role of steric hindrance in the performance of superplasticizers for concrete.” J. Am. Ceram. Soc. 80 (10): 2667–2671. https://doi.org/10.1111/j.1151-2916.1997.tb03169.x.
Zhang, C., J. Y. Fu, J. S. Yang, X. F. Ou, X. T. Ye, and Y. Zhang. 2018a. “Formulation and performance of grouting materials for underwater shield tunnel construction in karst ground.” Constr. Build. Mater. 187 (7): 327–338. https://doi.org/10.1016/j.conbuildmat.2018.07.054.
Zhang, C., J. S. Yang, X. F. Ou, J. Y. Fu, Y. P. Xie, and X. Liang. 2018b. “Clay dosage and water/cement ratio of lay-cement grout for optimal engineering performance.” Appl. Clay. Sci. 163 (7): 312–318. https://doi.org/10.1016/j.clay.2018.07.035.
Zhang, J., X. Guan, H. Li, and X. Liu. 2017a. “Performance and hydration study of ultra-fine sulfoaluminate cement-based double liquid grouting material.” Constr. Build. Mater. 132 (2): 262–270. https://doi.org/10.1016/j.conbuildmat.2016.11.135.
Zhang, W., S. Li, J. Wei, Q. Zhang, R. Liu, X. Zhang, and H. Y. Yin. 2017b. “Grouting rock fractures with cement and sodium silicate grout.” Carbonates Evaporites 33 (2): 1–12. https://doi.org/10.1007/s13146-016-0332-3.
Zhang, Z. Q., H. Y. Li, H. Y. Liu, G. J. Li, and X. Q. Shi. 2014. “Load transferring mechanism of pipe umbrella support in shallow-buried tunnels.” Tunnelling Underground Space Technol. 43 (7): 213–221. https://doi.org/10.1016/j.tust.2014.05.018.
Zhou, Y., D. Hou, J. Jiang, W. She, and J. Yu. 2017. “Reactive molecular simulation on the calcium silicate hydrates/polyethylene glycol composites.” Chem. Phys. Lett. 687 (11): 184–187. https://doi.org/10.1016/j.cplett.2017.09.020.
Zhu, H., B. Ye, Y. Cai, and F. Zhang. 2013. “An elasto-viscoplastic model for soft rock around tunnels considering over consolidation and structure effects.” Comput. Geotech. 50 (2): 6–16. https://doi.org/10.1016/j.compgeo.2012.12.004.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jun 1, 2018
Accepted: Dec 21, 2018
Published online: Apr 27, 2019
Published in print: Jul 1, 2019
Discussion open until: Sep 27, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.