Evaluation of Coal Ash–Based CLSM Made with Cementless Binder as a Thermal Grout for Borehole Heat Exchangers
Publication: Journal of Materials in Civil Engineering
Volume 31, Issue 6
Abstract
The primary goal of this study is to assess the characteristics of coal ash–based controlled low-strength material (CLSM) mixtures made with a cementless binder for the feasible usage as a thermal grout in borehole heat exchangers. In the experimental program, a group of CLSM mixtures made with cement or cementless binder through various ratios of water to binder () and water to solid (). The general properties (e.g., fresh density, flowability, initial setting time, bleeding, unconfined compressive strength, and microstructural analysis), and environmental impacts (e.g., corrosivity and heavy metals) were carried out on CLSM mixtures. Afterward, thermal conductivity was determined following a current specification for verification of the proposed CLSM, which is feasibly used as a thermal grout in geothermal systems (borehole heat exchangers). According to the results, all of the engineering properties and environmental impacts satisfied the specifications of CLSM. In addition, compared with the thermal conductivity values of conventional grouts, those of the proposed CLSM mixtures were higher. In conclusion, owing to good flowability and higher thermal conductivity than conventional grouts, the CLSMs made with cementless binder can be feasibly employed as a thermal grout for borehole heat exchangers.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by a National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (Grant No. NRF-2018R1A2B6007567).
References
ACI (American Concrete Institute). 1999. Controlled low strength materials. ACI 229R-99. Farmington Hill, MI: ACI.
Allan, M. L. 1997. Thermal conductivity of cementitious grouts for geothermal heat pumps. Upton, NY: Brookhaven National Laboratory.
Allan, M. L., and S. P. Kavanaugh. 1999. “Thermal conductivity of cementitious grouts and impact on heat exchanger length design for ground source heat pumps.” HVAC&R Res. 5 (2): 85–96. https://doi.org/10.1080/10789669.1999.10391226.
Alrtimi, A. A., M. Rouainia, and D. A. C. Manning. 2013. “Thermal enhancement of PFA-based grout for geothermal heat exchangers” Appl. Therm. Eng. 54 (2): 559–564. https://doi.org/10.1016/j.applthermaleng.2013.02.011.
ASTM. 2002. Standard test method for preparation and testing of Controlled Low Strength Material (CLSM) test cylinders. ASTM D4832. West Conshohocken, PA: ASTM.
ASTM. 2004. Standard specification for Portland cement. ASTM C150. West Conshohocken, PA: ASTM.
ASTM. 2007. Standard test method for density (unit weight), yield, cement content, and air content (gravimetric) of Controlled Low-Strength Material (CLSM). ASTM D6023. West Conshohocken, PA: ASTM.
ASTM. 2008. Standard test method for time of setting of concrete mixtures by penetration resistance. ASTM C403. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard test method for determination of thermal conductivity of soil and soft rock by thermal needle probe procedure. ASTM D5334. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard test method for expansion and bleeding of freshly mixed grouts for preplaced-aggregate concrete in the laboratory. ASTM C940. West Conshohocken, PA: ASTM.
ASTM. 2017a. Standard practice for classification of soils for engineering purposes (Unified soil classification system). ASTM D2487. West Conshohocken, PA: ASTM.
ASTM. 2017b. Standard test method for flow consistency of Controlled Low Strength Material (CLSM). ASTM D6103. West Conshohocken, PA: ASTM.
Bera, A. K., A. Ghosh, and A. Ghosh. 2007. “Compaction characteristics of pond ash.” J. Mater. Civ. Eng. 19 (4): 349–357. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:4(349).
CFR (Code of Federal Regulations). 2003. Applicability of treatment standards. CFR 268.40. Washington, DC: CFR.
Chantal, M. 2016. “Improvement of thermal conductivity of grout mixture for geothermal heat pump systems.” In Proc., Int. Refrigeration and Air Conditioning Conf. West Lafayette, IN: Purdue Univ.
Chittoori, B., A. J. Puppala, and A. Raavi. 2013. “Strength and stiffness characterization of controlled low-strength material using native high-plasticity clay.” J. Mater. Civ. Eng. 26 (6): 04014007 . https://doi.org/10.1061/(ASCE)MT.1943-5533.0000965.
Do, T. M., G. O. Kang, N. Vu, and Y. S. Kim. 2018. “Development of a new cementless binder for marine dredged soil stabilization: Strength behavior, hydraulic resistance capacity, microstructural analysis, and environmental impact.” Constr. Build. Mater. 186: 263–275.
Do, T. M., Y. S. Kim, and B. C. Ryu. 2015. “Improvement of engineering properties of pond ash based CLSM with cementless binder and artificial aggregates made of bauxite residue.” Int. J. Geo-Eng. 6 (1): 8–18. https://doi.org/10.1186/s40703-015-0008-1.
Du, L., K. J. Folliard, and D. Trejo. 2002. “Effects of constituent materials and quantities on water demand and compressive strength of controlled low-strength material.” J. Mater. Civ. Eng. 14 (6): 485–495. https://doi.org/10.1061/(ASCE)0899-1561(2002)14:6(485).
Eckhart, F. 1991. Grouting procedures of ground-source heat pump systems. Tulsa, OK: Ground Source Heat Pump Publications.
Gabr, M. A., and J. J. Bowders. 2000. “Controlled low-strength material using fly ash and AMD sludge.” J. Hazard Mater. 76 (2–3): 251–263.
KEMCO (Korea Energy Management Corporation). 2006. Gyeonggi-do, Korea: KEMCO.
Kim, Y. S., T. M. Do, H. K. Kim, and G. O. Kang. 2016. “Utilization of excavated soil in coal ash-based controlled low-strength material (CLSM).” Constr. Build. Mater. 124: 598–605. https://doi.org/10.1016/j.conbuildmat.2016.07.053.
Kuo, W. T., H. Y. Wang, C. Y. Shu, and D. S. Su. 2013. “Engineering properties of controlled low-strength materials containing waste oyster shells.” Constr. Build. Mater. 46: 128–133. https://doi.org/10.1016/j.conbuildmat.2013.04.020.
Lachemi, M., M. Sahmaran, K. M. A. Hossain, A. Lotfy, and M. Shehata. 2010. “Properties of controlled low-strength materials incorporating cement kiln dust and slag.” Cem. Concr. Compos. 32 (8): 623–629. https://doi.org/10.1016/j.cemconcomp.2010.07.011.
Lee, D. J. 2012. “A study on the thermal properties of cement-based grout for ground heat exchangers.” M.S. thesis, Dept. of Energy and Resources Engineering, Kangwon National Univ.
Lee, N. K., H. K. Kim, I. S. Park, and H. K. Lee. 2013. “Alkali-activated, cementless, controlled low-strength materials (CLSM) utilizing industrial by-products.” Constr. Build. Master. 49: 738–746. https://doi.org/10.1016/j.conbuildmat.2013.09.002.
Min, Y., Q. Jueshi, and P. Ying. 2008. “Activation of fly ash–lime systems using calcined phosphogypsum.” Constr. Build. Mater. 22 (5): 1004–1008.
Muhmood, L., S. Vitta, and D. Venkateswaran. 2009. “Cementitious and pozzolanic behavior of electric arc furnace steel slags.” Cem. Concr. Res. 39 (2): 102–109. https://doi.org/10.1016/j.cemconres.2008.11.002.
Mun, K. J., W. K. Hyoung, C. W. Lee, S. Y. So, and Y. S. Soh. 2007. “Basic properties of non-sintering cement using phosphogypsum and waste lime as activator.” Constr. Build. Mater. 21: 1342–1350. https://doi.org/10.1016/j.conbuildmat.2005.12.022.
Park, M. S., S. H. Min, J. H. Lim, J. M. Choi, and H. S. Choi. 2011. “Applicability of cement-based grout for ground heat exchanger considering heating-cooling cycles.” Sci. China Technol. Sci. 54 (7): 1661–1667. https://doi.org/10.1007/s11431-011-4388-y.
Philippacopoulos, A. J., and M. L. Berndt. 2001. “Influence of debonding in ground heat exchangers used with geothermal heat pumps.” Geothermics 30 (5): 527–545. https://doi.org/10.1016/S0375-6505(01)00011-6.
Plowman, C. 1984. “The chemistry of PFA in concrete: A review of current knowledge.” In Proc., 2nd Int. Conf. on Ash Technology and Marketing, 437–443. Ottawa, ON: ASH Technology Marketing.
Puppala, A. J., B. Chittoori, and A. Raavi. 2014. “Flowability and density characteristics of controlled low-strength material using native high-plasticity clay.” J. Mater. Civ. Eng. 27 (1): 06014026. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001127.
Raghavendra, T., and B. C. Udayashankar. 2013. “Flow and strength characteristics of CLSM using ground granulated blast furnace slag.” J. Mater. Civ. Eng. 26 (9): 04014050. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000927.
Ranganath, P. V., B. Bhattacharjee, and X. Krishnamoorthy. 1998. “Influence of size fraction of boned ash on its pozzolanic activity.” Cem. Concr. Res. 28 (5): 749–761. https://doi.org/10.1016/S0008-8846(98)00036-2.
Razak, H. A., S. Naganathan, and S. N. A. Hamid. 2009. “Performance appraisal of industrial waste incineration bottom ash as controlled low strength material.” J. Hazard Mater. 172 (2): 862–867. https://doi.org/10.1016/j.jhazmat.2009.07.070.
Remund, C. P., and J. T. Lund. 1993. “Thermal enhancement of bentonite grouts for vertical GSHP systems.” In Vol. 29 of Heat pump and refrigeration systems, edited by K. R. Den Braven and V. Mei, 95–106. New York: ASME.
Sengul, O., S. Azizi, F. Karaosmanoglu, and M. A. Tasdemir. 2011. “Effect of expanded perlite on the mechanical properties and thermal conductivity of lightweight concrete.” Energy Build. 43 (2/3): 671–676. https://doi.org/10.1016/j.enbuild.2010.11.008.
Sheen, Y. N., L. H. Zhang, and D. H. Le. 2013. “Engineering properties of soil-based controlled low-strength materials as slag partially substitutes to portland cement.” Constr. Build. Mater. 48: 822–829. https://doi.org/10.1016/j.conbuildmat.2013.07.046.
Tikalsky, P. J., H. U. Bahia, A. Deng, and T. Snyder. 2004. Excess foundry sand characterization and experimental investigation in controlled low-strength material and hot-mixing asphalt. University Park, PA: Pennsylvania State Univ.
USEPA. 1997. Hazardous waste management system, identification and listing of hazardous waste, proposed exclusion. Washington, DC: USEPA.
Xu, Y., and D. D. L. Chung. 2000. “Effect of sand addition on the specific heat and thermal conductivity of cement.” Cem. Concr. Res. 30 (1): 59–61. https://doi.org/10.1016/S0008-8846(99)00206-9.
Yan, D. Y. S., I. Y. Tang, and I. M. C. Lo. 2014. “Development of controlled low-strength material derived from beneficial reuse of bottom ash and sediment for green construction.” Constr. Build. Mater. 64: 201–207. https://doi.org/10.1016/j.conbuildmat.2014.04.087.
Yan, P., W. Yang, X. Qin, and Y. You. 1998. “Microstruture and properties of the binder of fly ash-fluorogypsum-portland cement.” Cem. Concr. Res. 29 (6): 349–354. https://doi.org/10.1016/S0008-8846(98)00214-2.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 31 • Issue 6 • June 2019
Copyright
©2019 American Society of Civil Engineers.
History
Received: Mar 11, 2018
Accepted: Nov 8, 2018
Published online: Mar 26, 2019
Published in print: Jun 1, 2019
Discussion open until: Aug 26, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.