Corrosion Improvement of Carbon Steel in Concrete Environment through Modification of Steel Microstructure
Publication: Journal of Materials in Civil Engineering
Volume 31, Issue 5
Abstract
This study investigated the impact of the grain size of low carbon steel on its electrochemical behavior in a simulated concrete pore solution. Specimens with three grain sizes were used: as-received; coarse, with grains approximately 2 times larger than those in the as-received steel; and fine, with grains approximately half the size of those in as-received specimens. Specimens were immersed in a chloride-free pore solution for 10 days and then 3% by weight NaCl was added to the solution. The specimens were then kept in the chloride-contaminated solution for 60 days. The corrosion behavior of the specimens was evaluated by different electrochemical measurement techniques. Results showed that fine specimens passivated first, followed by the coarse and as-received specimens. However, in chloride-contaminated pore solution, the as-received specimens corroded more, followed by the fine and coarse specimens. In fact, the coarse specimens remained passive after 60 days of exposure to the chloride-contaminated pore solution.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was conducted in the Corrosion Research Laboratory (CorRLab) at Clemson University. This study is funded by the National Science Foundation Grant No. 1552794, which is greatly acknowledged. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of the National Science Foundation.
References
Afshari, V., and C. Dehghanian. 2009. “Effects of grain size on the electrochemical corrosion behavior of electrodeposited nanocrystalline Fe coatings in alkaline solution.” Corros. Sci. 51 (8): 1844–1849. https://doi.org/10.1016/j.corsci.2009.05.015.
ASTM. 2012. Standard test methods for determining average grain size. ASTM E112. West Conshohocken, PA: ASTM.
ASTM. 2014. Metals handbook: Heat treating. West Conshohocken, PA: ASTM.
ASTM. 2018. Standard test method for conducting cyclic potentiodynamic polarization measurements for localized corrosion susceptibility iron-, nickel-, or cobalt-based alloys. ASTM G61-86. West Conshohocken, PA: ASTM.
Burke, L. D., and M. E. Lyons. 1986. “The formation and stability of hydrous oxide films on iron under potential cycling conditions in aqueous solution at high pH.” J. Electroanal. Chem. 198 (2): 347–368. https://doi.org/10.1016/0022-0728(86)90010-0.
Burke, L. D., and D. P. Whelan. 1980. “Growth of electrochromic film on nickel in base under potential cycling conditions.” J. Electroanal. Chem. 109 (1–3): 385–388. https://doi.org/10.1016/S0022-0728(80)80139-2.
Digges, T. G., S. J. Rosenberg, and G. W. Geil. 1966. Heat treatment and properties of iron and steel: National Bureau of Standards Monograph 88. Washington, DC: US Dept. of Commerce.
Foulkes, F. R., and P. McGrath. 1999. “Rapid cyclic voltammetric method for studying cement factors affecting the corrosion of reinforced concrete.” Cem. Concr. Res. 29 (6): 873–883. https://doi.org/10.1016/S0008-8846(99)00056-3.
Ghods, P. 2010. “Multi-scale investigation of the formation and breakdown of passive films on carbon steel rebar in concrete.” Ph.D. thesis, Dept. of Civil Engineering, Carlton Univ.
Ghosh, S. K., G. K. Dey, R. O. Dusane, and A. K. Grover. 2006. “Improved pitting corrosion behavior of electrodeposited nanocrystalline Ni–Cu alloys in 3.0 wt.% NaCl solution.” J. Alloys Compd. 426 (1–2): 235–243. https://doi.org/10.1016/j.jallcom.2005.12.094.
Gollapudi, S. 2012. “Grain size distribution effects on the corrosion behaviour of materials.” Corros. Sci. 62: 90–94. https://doi.org/10.1016/j.corsci.2012.04.040.
Hussain, R. R., A. Alhozaimy, A. Al-Negheimish, and D. D. N. Singh. 2014. “Time-dependent variation of the electrochemical impedance for thermo-mechanically treated versus plain low alloy steel rebars in contact with simulated concrete pore solution.” Constr. Build. Mater. 73: 283–288. https://doi.org/10.1016/j.conbuildmat.2014.09.099.
Image Metrology. 2018. “Scanning probe image processor (SPIP).” Accessed March 14, 2018. https://www.imagemet.com/products/spip/.
Jizhou, D., H. Baorong, H. Yanliang, S. Huyuan, L. Yan, and M. Shide. 2002. “Corrosion of mild steel in different granularity seabed sediment saturated with seawater.” Mater. Corros. 53 (11): 845–849. https://doi.org/10.1002/1521-4176(200211)53:11%3C845::AID-MACO845%3E3.0.CO;2-U.
Kalaignan, G. P., V. S. Muralidharan, and K. I. Vasu. 1987. “Triangular potential sweep voltammetric study of porous iron electrodes in alkali solutions.” J. Appl. Electrochem. 17 (5): 1083–1092. https://doi.org/10.1007/BF01024374.
MacDonald, D. D., and B. Roberts. 1978. “The cyclic voltammetry of carbon steel in concentrated sodium hydroxide solution.” Electrochim. Acta 23 (8): 781–786. https://doi.org/10.1016/0013-4686(78)80039-5.
Mahajan, S. W., G. Venkataraman, and A. K. Mallik. 1973. “Grain refinement of steel by cyclic rapid heating.” Metallography 6 (4): 337–345. https://doi.org/10.1016/0026-0800(73)90058-X.
Mahallati, E., and M. Saremi. 2006. “An assessment on the mill scale effects on the electrochemical characteristics of steel bars in concrete under DC-polarization.” Cem. Concr. Res. 36 (7): 1324–1329. https://doi.org/10.1016/j.cemconres.2006.03.015.
Marcotte, T. D. 2001. “Characterization of chloride-induced corrosion products that form in steel-reinforced cementitious materials.” Ph.D. thesis, Dept. of Mechanical Engineering, Univ. of Waterloo.
Poursaee, A. 2009. “Automatic system for monitoring corrosion of steel in concrete.” Adv. Eng. Software 40 (11): 1179–1182. https://doi.org/10.1016/j.advengsoft.2009.05.001.
Poursaee, A. 2010. “Potentiostatic transient technique, a simple approach to estimate the corrosion current density and Stern-Geary constant of reinforcing steel in concrete.” Cem. Concr. Res. 40 (9): 1451–1458. https://doi.org/10.1016/j.cemconres.2010.04.006.
Poursaee, A., and C. M. Hansson. 2007. “Reinforcing steel passivation in mortar and pore solution.” Cem. Concr. Res. 37 (7): 1127–1133. https://doi.org/10.1016/j.cemconres.2007.04.005.
Poursaee, A., and M. Saremi. 2012. “Corrosion of heat-treated steel bars in concrete synthetic pore solution.” Mag. Concr. Res. 64 (5): 395–400. https://doi.org/10.1680/macr.10.00142.
Ravikumar, M. K., T. S. Balasubramanian, K. Shukla, and S. Venugopalan. 1996. “A cyclic voltammetric study on the electrocatalysis of alkaline iron-electrode reactions.” J. Appl. Electrochem. 26 (11): 1111–1115. https://doi.org/10.1007/BF00243735.
Revie, E. W., and H. H. Uhlig. 2008. Corrosion and corrosion control: An introduction to corrosion science and engineering. Hoboken, NJ: Wiley.
Sánchez, M., J. Gregori, M. C. Alonso, J. J. García-Jareño, and F. Vicente. 2006. “Anodic growth of passive layers on steel rebars in an alkaline medium simulating the concrete pores.” Electrochim. Acta 52 (1): 47–53. https://doi.org/10.1016/j.electacta.2006.03.071.
Singh, J. K., and D. D. N. Singh. 2012. “The nature of rusts and corrosion characteristics of low alloy and plain carbon steels in three kinds of concrete pore solution with salinity and different pH.” Corros. Sci. 56: 129–142. https://doi.org/10.1016/j.corsci.2011.11.012.
Smith, W., and J. Hashemi. 2009. Foundations of materials science and engineering. New York: McGraw-Hill.
Tang, K. 2017. “Stray current induced corrosion of steel fibre reinforced concrete.” Cem. Concr. Res. 100: 445–456. https://doi.org/10.1016/j.cemconres.2017.08.004.
Torabati-Sarraf, H., and A. Poursaee. 2018. “Corrosion of coupled steels with different microstructures in concrete environment.” Constr. Build. Mater. 167: 680–687. https://doi.org/10.1016/j.conbuildmat.2018.02.083.
Totten, G. E. 2006. Steel heat treatment: Metallurgy and technologies. Boca Raton, FL: CRC Press.
Trejo, D., and P. J. Monteiro. 2005. “Corrosion performance of conventional (ASTM A615) and low-alloy (ASTM A706) reinforcing bars embedded in concrete and exposed to chloride environments.” Cem. Concr. Res. 35 (3): 562–571. https://doi.org/10.1016/j.cemconres.2004.06.004.
Wang, W., H. Chen, X. Li, and Z. Zhu. 2017. “Corrosion behavior of steel bars immersed in simulated pore solutions of alkali-activated slag mortar.” Constr. Build. Mater. 143: 289–297. https://doi.org/10.1016/j.conbuildmat.2017.03.132.
Wang, L., Y. Lin, Z. Zeng, W. Liu, Q. Xue, L. Hua, and J. Zhang. 2007. “Electrochemical corrosion behavior of nanocrystalline Co coatings explained by higher grain boundary density.” Electrochim. Acta 52 (13): 4342–4350. https://doi.org/10.1016/j.electacta.2006.12.009.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jun 10, 2018
Accepted: Oct 22, 2018
Published online: Mar 4, 2019
Published in print: May 1, 2019
Discussion open until: Aug 4, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.