Performance and Microstructure of Carbonated MgO Samples under High Temperatures
Publication: Journal of Materials in Civil Engineering
Volume 31, Issue 3
Abstract
This study investigated the changes in the performance and microstructure of carbonated MgO samples subjected to 40°C–550°C in water, oven, and furnace conditions. Although sample strength remained relatively stable until 80°C, an obvious reduction was observed in higher temperatures. This performance decline was attributed to the changes in the content and morphology of the strength providing carbonate phases (hydromagnesite). Phase quantification results revealed lower hydromagnesite content with smaller crystal sizes at . The decarbonation of hydromagnesite, followed by dehydration of brucite to MgO at higher temperatures of 550°C, revealed the relationship between the stability of major phases and sample performance.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge the financial support from the Singapore MOE Academic Research Fund Tier 1 (RG 95/16) for the completion of this research project.
References
Ballirano, P., C. De Vito, V. Ferrini, and S. Mignardi. 2010. “The thermal behaviour and structural stability of nesquehonite, , evaluated by in situ laboratory parallel-beam X-ray powder diffraction: new constraints on sequestration within minerals.” J. Hazard. Mater. 178 (1): 522–528. https://doi.org/10.1016/j.jhazmat.2010.01.113.
Ballirano, P., C. De Vito, S. Mignardi, and V. Ferrini. 2013. “Phase transitions in the system and the thermal decomposition of dypingite, : Implications for geosequestration of carbon dioxide.” Chem. Geol. 340: 59–67. https://doi.org/10.1016/j.chemgeo.2012.12.005.
Botha, A., and C. Strydom. 2001. “Preparation of a magnesium hydroxy carbonate from magnesium hydroxide.” Hydrometallurgy 62 (3): 175–183. https://doi.org/10.1016/S0304-386X(01)00197-9.
Chaka, A. M., and A. R. Felmy. 2014. “Ab initio thermodynamic model for magnesium carbonates and hydrates.” J. Phys. Chem. A 118 (35): 7469–7488. https://doi.org/10.1021/jp500271n.
Dung, N., and C. Unluer. 2016. “Improving the performance of reactive MgO cement-based concrete mixes.” Constr. Build. Mater. 126: 747–758. https://doi.org/10.1016/j.conbuildmat.2016.09.090.
Dung, N., and C. Unluer. 2017a. “Carbonated MgO concrete with improved performance: The influence of temperature and hydration agent on hydration, carbonation and strength gain.” Cem. Concr. Compos. 82: 152–164. https://doi.org/10.1016/j.cemconcomp.2017.06.006.
Dung, N., and C. Unluer. 2017b. “Influence of nucleation seeding on the performance of carbonated MgO formulations.” Cem. Concr. Compos. 83: 1–9. https://doi.org/10.1016/j.cemconcomp.2017.07.005.
Dung, N., and C. Unluer. 2017c. “Sequestration of in reactive MgO cement-based mixes with enhanced hydration mechanisms.” Constr. Build. Mater. 143: 71–82. https://doi.org/10.1016/j.conbuildmat.2017.03.038.
Fernández, A. I., J. M. Chimenos, M. Segarra, M. A. Fernández, and F. Espiell. 2000. “Procedure to obtain hydromagnesite from a MgO-containing residue. Kinetic study.” Ind. Eng. Chem. Res. 39 (10): 3653–3658. https://doi.org/10.1021/ie0003180.
Frost, R. L., S. Bahfenne, J. Graham, and W. N. Martens. 2008. “Thermal stability of artinite, dypingite and brugnatellite—Implications for the geosequestration of green house gases.” Thermochim. Acta 475 (1): 39–43. https://doi.org/10.1016/j.tca.2008.06.007.
Frost, R. L., and S. J. Palmer. 2011. “Infrared and infrared emission spectroscopy of nesquehonite -implications for the formula of nesquehonite.” Spectrochim. Acta, Part A 78 (4): 1255–1260. https://doi.org/10.1016/j.saa.2010.12.059.
Hänchen, M., V. Prigiobbe, R. Baciocchi, and M. Mazzotti. 2008. “Precipitation in the Mg-carbonate system—Effects of temperature and pressure.” Chem. Eng. Sci. 63 (4): 1012–1028. https://doi.org/10.1016/j.ces.2007.09.052.
Hollingbery, L., and T. Hull. 2010. “The thermal decomposition of huntite and hydromagnesite: A review.” Thermochim. Acta 509 (1): 1–11. https://doi.org/10.1016/j.tca.2010.06.012.
Hopkinson, L., P. Kristova, K. Rutt, and G. Cressey. 2012. “Phase transitions in the system during degassing of Mg-bearing solutions.” Geochim. Cosmochim. Acta 76: 1–13. https://doi.org/10.1016/j.gca.2011.10.023.
Huijgen, W. J. J., and R. N. J. Comans. 2003. Carbon dioxide sequestration by mineral carbonation: Literature review. Vienna, Austria: Vienna International Centre.
Jauffret, G., J. Morrison, and F. Glasser. 2015. “On the thermal decomposition of nesquehonite.” J. Therm. Anal. Calorim. 122 (2): 601–609. https://doi.org/10.1007/s10973-015-4756-0.
Jin, F., and A. Al-Tabbaa. 2013. “Thermogravimetric study on the hydration of reactive magnesia and silica mixture at room temperature.” Thermochim. Acta 566: 162–168. https://doi.org/10.1016/j.tca.2013.05.036.
Königsberger, E., L.-C. Königsberger, and H. Gamsjäger. 1999. “Low-temperature thermodynamic model for the system .” Geochim. Cosmochim. Acta 63 (19/20): 3105–3119. https://doi.org/10.1016/S0016-7037(99)00238-0.
Li, X. 2013. “Mechanical properties and durability performance of reactive magnesia cement concrete.” Ph.D. dissertation, Dept. of Engineering, Univ. of Cambridge.
Liska, M. 2009. “Properties and applications of reactive magnesia cements in porous blocks.” Ph.D. dissertation, Dept. of Engineering, Cambridge Univ.
Liska, M. 2010. “Properties and applications of reactive magnesia cements in porous blocks.” Ph.D. thesis, Dept. of Engineering, Univ. of Cambridge.
Liska, M., and A. Al-Tabbaa. 2009. “Ultra-green construction: Reactive magnesia masonry products.” Proc., ICE: Waste Waste Resour. Manage. 162 (4): 185–196. https://doi.org/10.1680/warm.2009.162.4.185.
Liska, M., and A. Al-Tabbaa. 2012. “Performance of magnesia cements in porous blocks in acid and magnesium environments.” Adv. Cem. Res. 24 (4): 221–232. https://doi.org/10.1680/adcr.11.00011.
Liska, M., A. Al-Tabbaa, K. Carter, and J. Fifield. 2012a. “Scaled-up commercial production of reactive magnesia cement pressed masonry units. Part II: Performance.” Proc. Inst. Civ. Eng. Constr. Mater. 165 (4): 225–243. https://doi.org/10.1680/coma.10.00031.
Liska, M., A. Al-Tabbaa, K. Carter, and J. Fifield. 2012b. “Scaled-up commercial production of reactive magnesium cement pressed masonry units. Part I: Production.” Proc. Inst. Civ. Eng. Constr. Mater. 165 (4): 211–223. https://doi.org/10.1680/coma.10.00032.
Liska, M., L. Vandeperre, and A. Al-Tabbaa. 2006. “Mixtures of pulverised fuel ash, portland cement and magnesium oxide: Characterisation of pastes and setting behaviour.” In Proc., WASCON, 563–573. Netherlands: International Society for the Environmental and Technical Implications of Construction with Alternative Materials.
Liska, M., L. Vandeperre, and A. Al-Tabbaa. 2008. “Influence of carbonation on the properties of reactive magnesia cement-based pressed masonry units.” Adv. Cem. Res. 20 (2): 53–64. https://doi.org/10.1680/adcr.2008.20.2.53.
Marini, L. 2007. Geological sequestration of carbon dioxide: Thermodynamics, kinetics and reaction path modeling. Oxford, UK: Elsevier.
Ming, D. W., and W. T. Franklin. 1985. “Synthesis of lansfordite and nesquehonite.” Soil Sci. Soc. Am. J. 49 (5): 1303–1308. https://doi.org/10.2136/sssaj1985.03615995004900050046x.
Mo, L., and D. K. Panesar. 2012. “Effects of accelerated carbonation on the microstructure of portland cement pastes containing reactive MgO.” Cem. Concr. Res. 42 (6): 769–777. https://doi.org/10.1016/j.cemconres.2012.02.017.
Mo, L., and D. K. Panesar. 2013. “Accelerated carbonation—A potential approach to sequester in cement paste containing slag and reactive MgO.” Cem. Concr. Compos. 43: 69–77. https://doi.org/10.1016/j.cemconcomp.2013.07.001.
Pu, L., and C. Unluer. 2016. “Investigation of carbonation depth and its influence on the performance and microstructure of MgO cement and PC mixes.” Constr. Build. Mater. 120: 349–363. https://doi.org/10.1016/j.conbuildmat.2016.05.067.
Ruan, S., and C. Unluer. 2016. “Comparative life cycle assessment of reactive MgO and portland cement production.” J. Cleaner Prod. 137: 258–273. https://doi.org/10.1016/j.jclepro.2016.07.071.
Ruan, S., and C. Unluer. 2017a. “Effect of air entrainment on the performance of reactive MgO and PC mixes.” Constr. Build. Mater. 142: 221–232. https://doi.org/10.1016/j.conbuildmat.2017.03.068.
Ruan, S., and C. Unluer. 2017b. “Influence of mix design on the carbonation, mechanical properties and microstructure of reactive MgO cement-based concrete.” Cem. Concr. Compos. 80: 104–114. https://doi.org/10.1016/j.cemconcomp.2017.03.004.
Sobolev, K., and A. Amirjanov. 2010. “Application of genetic algorithm for modeling of dense packing of concrete aggregates.” Constr. Build. Mater. 24 (8): 1449–1455. https://doi.org/10.1016/j.conbuildmat.2010.01.010.
Szczerba, J., R. Prorok, E. Śnieżek, D. Madej, and K. Maślona. 2013. “Influence of time and temperature on ageing and phases synthesis in the system.” Thermochim. Acta 567: 57–64. https://doi.org/10.1016/j.tca.2013.01.018.
Teir, S., S. Eloneva, C.-J. Fogelholm, and R. Zevenhoven. 2009. “Fixation of carbon dioxide by producing hydromagnesite from serpentinite.” Appl. Energy 86 (2): 214–218. https://doi.org/10.1016/j.apenergy.2008.03.013.
Unluer, C. 2012. “Enhancing the carbonation of reactive magnesia cement-based porous blocks.” Ph.D. dissertation, Dept. of Engineering, Univ. of Cambridge.
Unluer, C., and A. Al-Tabbaa. 2011 “Green construction with carbonating reactive magnesia porous blocks: Effect of cement and water contents.” In Proc., 2nd Int. Conf. on Future Concrete. Dubai, United Arab Emirates.
Unluer, C., and A. Al-Tabbaa. 2013. “Impact of hydrated magnesium carbonate additives on the carbonation of reactive MgO cements.” Cem. Concr. Res. 54: 87–97. https://doi.org/10.1016/j.cemconres.2013.08.009.
Unluer, C., and A. Al-Tabbaa. 2014. “Enhancing the carbonation of MgO cement porous blocks through improved curing conditions.” Cem. Concr. Res. 59: 55–65. https://doi.org/10.1016/j.cemconres.2014.02.005.
Unluer, C., and A. Al-Tabbaa. 2015. “The role of brucite, ground granulated blastfurnace slag, and magnesium silicates in the carbonation and performance of MgO cements.” Constr. Build. Mater. 94: 629–643. https://doi.org/10.1016/j.conbuildmat.2015.07.105.
Vágvölgyi, V., M. Hales, R. L. Frost, A. Locke, J. Kristóf, and E. Horváth. 2008. “Conventional and controlled rate thermal analysis of nesquehonite .” J. Therm. Anal. Calorim. 94 (2): 523–528. https://doi.org/10.1007/s10973-007-8844-7.
Vandeperre, A., and L. J. Al-Tabbaa. 2007. “Accelerated carbonation of reactive MgO cements.” Adv. Cem. Res. 19 (2): 67–79. https://doi.org/10.1680/adcr.2007.19.2.67.
Xiong, Y., and A. S. Lord. 2008. “Experimental investigations of the reaction path in the system in solutions with various ionic strengths, and their applications to nuclear waste isolation.” Appl. Geochem. 23 (6): 1634–1659. https://doi.org/10.1016/j.apgeochem.2007.12.035.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Mar 25, 2018
Accepted: Aug 30, 2018
Published online: Jan 2, 2019
Published in print: Mar 1, 2019
Discussion open until: Jun 2, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.