Effect of Manganese Dioxide Nanorods on the Thermoelectric Properties of Cement Composites
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 9
Abstract
The Seebeck coefficient of plain cement paste is usually less than . To enhance the thermoelectric performance of cement composites, a kind of powder was synthesized and used as a thermoelectric component in this work. The synthesized powder was proven to be a kind of effective thermoelectric component in cement paste. The synthesized powder possesses a nanorod structure with a diameter of about 50 nm and a length up to 1.4 μm. The measured Seebeck coefficient of the compacted powders was about . The nanorod structured design was proven to be an effective method to increase the Seebeck coefficient of the thermoelectric component in this research. Then the nanorods were incorporated into the cement matrix to enhance the thermoelectric effect of cement composites. A relatively high Seebeck coefficient of about could be obtained when the content of powder was 5.0% by weight of cement, which is more than 1,000 times higher than that of the cement paste without powder. And at this content, the electrical conductivity, thermal conductivity, and of cement composites were , , and , respectively. The thermoelectric effect of the cement composites is enhanced mainly due to the enhanced Seebeck coefficient, while the influence of electrical conductivity and thermal conductivity caused by powders is not as obvious as Seebeck coefficient.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Thanks for the financial support provided by National Science Foundation of China (Nos. 51378391 and 51525903), National Key Projects of China (2016YFC0700800), Shandong Provincial Key Research and Development Plan (No. 2017GHY15118), and Nantong Science and Technology Plan (No. GY12016046).
References
Baeza, F. J., O. Galao, E. Zornoza, and P. Garcés. 2013. “Effect of aspect ratio on strain sensing capacity of carbon fiber reinforced cement composites.” Mater. Des. 51: 1085–1094. https://doi.org/10.1016/j.matdes.2013.05.010.
Bell, L. E. 2008. “Cooling, heating, generating power and recovering waste heat with thermoelectric systems.” Science 321 (5895): 1457–1461. https://doi.org/10.1126/science.1158899.
Borisova, L. D. 1979. “Thermoelectric properties of impurity doped PbTe.” Phys. Status Solidi. 53 (1): K19–K22. https://doi.org/10.1002/pssa.2210530157.
Cao, H., W. Yao, and J. Qin. 2011. “Seebeck effect in graphite-carbon fiber cement based composite.” Adv. Mater. Res. 177: 566–569. https://doi.org/10.4028/www.scientific.net/AMR.177.566.
Cao, J., and D. D. L. Chung. 2005. “Role of moisture in the Seebeck effect in cement-based materials.” Cem. Concr. Res. 35 (4): 810–812. https://doi.org/10.1016/j.cemconres.2004.05.036.
Cheng, F. Y., J. Z. Zhao, W. Song, C. S. Li, H. Ma, J. Chen, and P. W. Shen. 2006. “Facile controlled synthesis of nanostructures of novel shapes and their application in batteries.” Inorg. Chem. 45 (5): 2038–2044. https://doi.org/10.1021/ic051715b.
CSI (Chinese Standards Institution). 2000. Methods for testing uniformity of concrete mixture. GB/T 8077. Beijing: CSI.
Demirel, B., and S. Yazicioglu. 2008. “Thermoelectric behavior of carbon fiber reinforced lightweight concrete with mineral admixtures.” New Carbon Mater. 23 (1): 21–24. https://doi.org/10.1016/S1872-5805(08)60009-8.
Farid ul Islam, A. K. M., R. Islam, and K. A. Khan. 2005. “Studies of the thermoelectric effect in semiconducting thin films.” J. Mater. Sci. Mater. Electron. 16 (4): 203–207. https://doi.org/10.1007/s10854-005-0766-1.
Feng, Y., X. Jiang, E. Ghafari, B. Kucukgok, C. Zhang, I. Ferguson, and N. Lu. 2017. “Metal oxides for thermoelectric power generation and beyond.” Adv. Compos. Hybrid Mater. 1 (1): 1–13. https://doi.org/10.1007/s42114-017-0011-4.
Ghafari, E., S. A. Ghahari, Y. Feng, F. Severgnini, and N. Lu. 2016. “Effect of zinc oxide and Al-zinc oxide nanoparticles on the rheological properties of cement paste.” Compos. Part B: Eng. 105: 160–166. https://doi.org/10.1016/j.compositesb.2016.08.040.
Ghaharia, S., E. Ghafaria, and N. Lu. 2017. “Effect of ZnO nanoparticles on thermoelectric properties of cement composite for waste heat harvesting.” Constr. Build. Mater. 146: 755–763. https://doi.org/10.1016/j.conbuildmat.2017.04.165.
Guan, H. T., S. H. Liu, Y. P. Duan, and J. Cheng. 2006. “Cement based electromagnetic shielding and absorbing building materials.” Cem. Concr. Compos. 28 (5): 468–474. https://doi.org/10.1016/j.cemconcomp.2005.12.004.
Harringa, J. L., and B. A. Cook. 1999. “Application of hot isostatic pressing for consolidation of n-type silicon-germanium alloys prepared by mechanical alloying.” Mater. Sci. Eng. B 60 (2): 137–142. https://doi.org/10.1016/S0921-5107(99)00023-9.
He, S. J., and W. Chen. 2014. “High performance supercapacitors based on three-dimensional ultralight flexible manganese oxide nanosheets/carbon foam composites.” J. Power Sources 262 (15): 391–400. https://doi.org/10.1016/j.jpowsour.2014.03.137.
Hedden, M., N. Francis, J. T. Haraldsen, T. Ahmed, and C. Constantin. 2015. “Thermoelectric properties of nano-meso-micro powders as a function of electrical resistance.” Nanoscale Res. Lett. 10 (1): 292–300. https://doi.org/10.1186/s11671-015-1000-6.
Hicks, L. D., and M. S. Dresselhaus. 1993. “Effect of quantum-well structures on the thermoelectric figure of merit.” Phys. Rev. B 47 (19): 12727–12731. https://doi.org/10.1103/PhysRevB.47.12727.
Hutagalung, S. D., N. H. Sahrol, Z. A. Ahmad, M. F. Ain, and M. Othman. 2012. “Effect of additive on the dielectric and electromagnetic interference shielding properties of sintered cement-based ceramics.” Ceram. Int. 38 (1): 671–678. https://doi.org/10.1016/j.ceramint.2011.07.055.
Ionesou, R., J. Jaklovszky, N. Nistor, and A. Chiculita. 1975. “Grain size effects on thermal electrical properties of sintered solid solutions based on .” Phys. Status Solid. 27 (1): 27–33.
Ji, T., X. Zhang, and W. H. Li. 2016. “Enhanced thermoelectric effect of cement composite by addition of metallic oxide nanopowders for energy harvesting in buildings.” Constr. Build. Mater. 115: 576–581. https://doi.org/10.1016/j.conbuildmat.2016.04.035.
Kucukgok, B., B. Wang, A. G. Melton, N. Lu, and I. T. Ferguson. 2014. “Comparison of thermoelectric properties of GaN and ZnO samples.” Phys. Status Solidi C 11 (3–4): 894–897. https://doi.org/10.1002/pssc.201300538.
Lan, Y., A. J. Minnich, G. Chen, and Z. Ren. 2010. “Enhancement of thermoelectric figure-of-merit by a bulk nanostructuring approach.” Adv. Funct. Mater. 20 (3): 357–376. https://doi.org/10.1002/adfm.200901512.
Lu, N., and I. Ferguson. 2013. “III-nitrides for energy production: Photovoltaic and thermoelectric applications.” Semicond. Sci. Technol. 28 (7): 074023. https://doi.org/10.1088/0268-1242/28/7/074023.
Osborn, D., M. Hassan, S. Asadi, and J. R. White. 2014. “Durability quantification of surface coating on concrete and asphalt pavements.” J. Mater. Civ. Eng. 26 (2): 331–337. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000816.
Pichanusakorn, P., and P. Bandaru. 2010. “Nanostructured thermoelectrics.” Mater. Sci. Eng. R 67 (2–4): 19–63. https://doi.org/10.1016/j.mser.2009.10.001.
Pollock, D. D. 1985. Thermoelectricity: Theory, thermometry, tool. West Conshohocken, PA: ASTM.
Preisler, E. 1976. “Semiconductor properties of manganese dioxide.” J. Appl. Electrochem. 6 (4): 311–320. https://doi.org/10.1007/BF00608916.
Rajabipour, F., and J. Weiss. 2007. “Electrical conductivity of drying cement paste.” Mater. Struct. 40 (10): 1143–1160. https://doi.org/10.1617/s11527-006-9211-z.
Reza, F., G. B. Batson, J. A. Yamamuro, and J. S. Lee. 2003. “Resistance changes during compression of carbon fiber cement composites.” J. Mater. Civ. Eng. 15 (5): 476–483. https://doi.org/10.1061/(ASCE)0899-1561(2003)15:5(476).
Riffat, S. B., and X. L. Ma. 2004. “Improving the coefficient of performance of thermoelectric cooling systems: A review.” Int. J. Energy Res. 28 (9): 753–768. https://doi.org/10.1002/er.991.
Song, F. F., L. Wu, and S. Liang. 2012. “Giant Seebeck coefficient thermoelectric device of powder.” Nanotechnology 23 (8): 085401. https://doi.org/10.1088/0957-4484/23/8/085401.
Sun, M., Z. Li, Q. Mao, and D. Shen. 1998. “Thermoelectric percolation phenomenon in carbon fiber-reinforced concrete.” Cem. Concr. Res. 28 (12): 1707–1712. https://doi.org/10.1016/S0008-8846(98)00161-6.
Tong, T., et al. 2013. “Suppression of thermal conductivity in alloys by nanometer-scale disorder.” Appl. Phys. Lett. 102 (12): 121906 https://doi.org/10.1063/1.4798838.
Toupin, M., T. Brousse, and D. Belanger. 2002. “Influence of microstructure on the charge storage properties of chemically synthesized manganese dioxide.” Chem. Mater. 14 (9): 3946–3952. https://doi.org/10.1021/cm020408q.
Ur, S. C., P. Nash, and I. H. Kim. 2003. “Mechanical alloying and thermoelectric properties of .” J. Mater. Sci. 38 (17): 3553–3558. https://doi.org/10.1023/A:1025608926808.
Walia, S., et al. 2013a. “-based thermopower wave sources with exceptionally large output voltages.” J. Phys. Chem. C 117 (18): 9137–9142. https://doi.org/10.1021/jp401731b.
Walia, S., S. Balendhran, H. Nili, S. Zhuiykov, G. Rosengarten, Q. H. Wang, M. Bhaskaran, S. Sriram, M. Strano, and K. Kalantar-zadeh. 2013b. “Transition metal oxides: Thermoelectric properties.” Prog. Mater. Sci. 58 (8): 1443–1489. https://doi.org/10.1016/j.pmatsci.2013.06.003.
Wang, H., Z. Lu, D. Qian, Y. Li, and W. Zhang. 2007. “Single-crystal nanorods: Synthesis and electrochemical properties.” Nanotechnology 18 (11): 115616. https://doi.org/10.1088/0957-4484/18/11/115616.
Wang, Z., Z. Wang, M. Ning, S. Tang, and Y. He. 2017. “Electro-thermal properties and Seebeck effect of conductive mortar and its use in self-heating and self-sensing system.” Ceram. Int. 43 (12): 8685–8693. https://doi.org/10.1016/j.ceramint.2017.03.202.
Wei, J., L. Hao, G. He, and C. Yang. 2014a. “Enhanced thermoelectric effect of carbon fiber reinforced cement composites by metallic oxide/cement interface.” Ceram. Int. 40 (6): 8261–8263. https://doi.org/10.1016/j.ceramint.2014.01.024.
Wei, J., Z. Nie, G. He, L. Hao, L. Zhao, and Q. Zhang. 2014b. “Energy harvesting from solar irradiation in cities using the thermoelectric behavior of carbon fiber reinforced cement composites.” RSC Adv. 4 (89): 48128–48134. https://doi.org/10.1039/C4RA07864K.
Wei, J., Q. Zhang, L. Zhao, L. Hao, and Z. Nie. 2017. “Effect of moisture on the thermoelectric properties in expanded graphite/carbon fiber cement composites.” Ceram. Int. 43 (14): 10763–10769. https://doi.org/10.1016/j.ceramint.2017.05.088.
Wei, J., Q. Zhang, L. Zhao, L. Hao, and C. Yang. 2016. “Enhanced thermoelectric properties of carbon fiber reinforced cement composites.” Ceram. Int. 42 (10): 11568–11573. https://doi.org/10.1016/j.ceramint.2016.04.014.
Wen, S., and D. D. L. Chung. 1999. “Seebeck effect in carbon fiber reinforced cement.” Cem. Concr. Res. 29 (12): 1989–1993. https://doi.org/10.1016/S0008-8846(99)00185-4.
Wen, S., and D. D. L. Chung. 2000. “Seebeck effect in steel fiber reinforced cement.” Cem. Concr. Res. 30 (4): 661–664. https://doi.org/10.1016/S0008-8846(00)00205-2.
Wen, S., and D. D. L. Chung. 2002. “Thermoelectric behavior of carbon-cement composites.” Carbon 40 (13): 2495–2497. https://doi.org/10.1016/S0008-6223(02)00142-2.
Xia, X., H. Li, and Z. H. Chen. 1989. “The study of semiconduction properties of with different degrees of reduction.” J. Electrochem. Soc. 136 (1): 266–271. https://doi.org/10.1149/1.2096600.
Zhou, C., A. Ghods, K. L. Yunghans, V. G. Saravade, P. V. Patel, X. Jiang, B. Kucukgok, N. Lu, and I. Ferguson. 2017. “ZnO for solar cell and thermoelectric applications.” In Proc., SPIE 10105, Oxide-Based Materials and Devices VIII, 101051K. Bellingham, WA: SPIE—International Society for Optical Engineering.
Zuo, J., W. Yao, X. Liu, and K. Wu. 2012. “Sensing properties of carbon nanotube-carbon fiber/cement nanocomposites.” J. Test. Eval. 40 (5): 838–843. https://doi.org/10.1520/JTE20120092.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Sep 21, 2017
Accepted: Feb 23, 2018
Published online: Jul 2, 2018
Published in print: Sep 1, 2018
Discussion open until: Dec 2, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.