Curing Method and Mix Design Evaluation of a Styrene-Acrylic Based Liquid Polymer for Sand and Clay Stabilization
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 9
Abstract
The curing of soil specimens treated with a liquid polymer soil stabilizer of styrene acrylic family was studied through an extensive laboratory testing program. First, the effect of different curing environments including air, water and heating on the unconfined compressive strength (UCS) of stabilized sand was studied to identify suitable curing environments. Furthermore, a parametric study was conducted through which the liquid content of the specimens (i.e., polymer + water) was varied and the overall performance of treated specimens of sand and sulfate-rich high plasticity clay was assessed. The optimally treated specimens (i.e., with the best curing environment and optimal stabilizer dosage) were evaluated for their (1) short-term performance, (2) swelling potentials of treated high plasticity clay, and (3) durability after 24 wet–dry or freeze–thaw cycles. The results suggested that heating can significantly expedite the curing; conversely, soaking the specimens in water showed a detrimental effect in terms of the resultant strength. The strongest specimens were achieved when no extra water in addition to the liquid stabilizer was added when treating the soil. As to clay, the liquid polymer showcased excellent performance in reducing the swelling potential but the strength of the specimens was highly decreased by to moisture and freeze–thaw cycles.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors of this paper would like to greatly acknowledge the help of Dr. Murali Subramaniam and Mr. Scott Hazelrigg at Intec of San Antonio who assisted in testing the specimens. A major part of the testing program was conducted at the Geomaterials Laboratory of the University of Texas at San Antonio under the supervision of Dr. Samer Dessouky. The liquid polymer was provided by the Mallard Creek Polymers Inc. This research did not receive any specific grant from funding agencies in the public, commercial, or not-for-profit sectors. The contents of this paper reflect the views of the authors and do not necessarily reflect the views of those who helped the authors with this project.
References
Ajalloeian, R., H. Matinmanesh, S. Abtahi, and M. Rowshanzamir. 2013. “Effect of polyvinyl acetate grout injection on geotechnical properties of fine sand.” Geomech. Geoeng. 8 (2): 86–96. https://doi.org/10.1080/17486025.2012.705897.
Al-Khanbashi, A., and S. Abdalla. 2006. “Evaluation of three waterborne polymers as stabilizers for sandy soil.” Geotech. Geol. Eng. 24 (6): 1603–1625. https://doi.org/10.1007/s10706-005-4895-3.
Al-Khanbashi, A., and M. El-Gamal. 2003. “Modification of sandy soil using water-borne polymer.” J. Appl. Polym. Sci. 88 (10): 2484–2491.
Anagnostopoulos, C., and S. Hadjispyrou. 2004. “Laboratory study of an epoxy resin grouted sand.” Ground Improv. 8 (1): 39–45. https://doi.org/10.1002/app.12066.
Anagnostopoulos, C., P. Kandiliotis, M. Lola, and S. Karavatos. 2013. “Effect of epoxy resin mixtures on the physical and mechanical properties of sand.” Res. J. Appl. Sci. Eng. Technol. 7 (17): 3478–3490.
Anagnostopoulos, C., and T. Papaliangas. 2012. “Experimental investigation of epoxy resin and sand mixes.” J. Geotech. Geoenviron. Eng. 138 (7): 841–849. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000648.
ASTM. 1996. Standard test method for freezing and thawing compacted soil-cement mixtures. ASTM D560. West Conshohocken, PA: ASTM.
ASTM. 2003. Standard test methods for wetting and drying compacted soil-cement mixtures. ASTM D559. West Conshohocken, PA: ASTM.
ASTM. 2007. Standard guide for wet sieve analysis of ceramic whiteware clays. ASTM C325. West Conshohocken, PA: ASTM.
ASTM. 2014a. Standard test method for sieve analysis of fine and coarse aggregates. ASTM C136. West Conshohocken, PA: ASTM.
ASTM. 2014b. Standard test methods for one-dimensional swell or collapse of soils. ASTM D4546. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard test method for unconfined compressive strength of cohesive soil. ASTM D2166. West Conshohocken, PA: ASTM.
Azzam, W. 2012. “Reduction of the shrinkage-swelling potential with polymer nanocomposite stabilization.” J. Appl. Polym. Sci. 123 (1): 299–306. https://doi.org/10.1002/app.33642.
Camberfort, H. 1977. “The principles and applications of grouting.” Q. J. Eng. Geol. Hydrogeol. 10 (2): 57–95.
Gilazghi, S., J. Huang, S. Rezaeimalek, and S. Bin-Shafique. 2016. “Stabilizing sulfate-rich high plasticity clay with moisture activated polymerization.” Eng. Geol. 211: 171–178. https://doi.org/10.1016/j.enggeo.2016.07.007.
Harris, J., S. Sebesta, and T. Scullion. 2004. “Hydrated lime stabilization of sulfate-bearing vertisols in Texas.” Transp. Res. Rec. 1868: 31–39. https://doi.org/10.3141/1868-04.
Hilf, J. 1991. “Compacted fill.” In Foundation engineering handbook. 2nd ed., edited by H. Fang, 249–316. Berlin: Springer.
Hoy, M., R. Rachan, S. Horpibulsuk, A. Arulrajah, and M. Mirzababaei. 2017. “Effect of wetting-drying cycles on compressive strength and microstructure of recycled asphalt pavement: Fly ash geopolymer.” Constr. Build. Mater. 144: 624–634. https://doi.org/10.1016/j.conbuildmat.2017.03.243.
Imbabi, M., C. Carrigan, and S. McKenna. 2012. “Trends and developments in green cement and concrete technology.” Int. J. Sustainable Built Environ. 1 (2): 194–216. https://doi.org/10.1016/j.ijsbe.2013.05.001.
Ingles, O. G., and Metcalf, J. B. 1973. Soil stabilization: Principles and practice, 374. New York: Wiley.
Jones, E., A. Ajayi-Majebi, W. Grissom, L. Smith, and E. Jones. 1991. “Epoxy-resin-based chemical stabilization of a fine, poorly graded soil system.” Transp. Res. Rec. 1295: 95–108.
Katz, L., A. Rauch, H. Liljestrand, J. Harmon, K. Shaw, and H. Albers 2001. “Mechanisms of soil stabilization with liquid ionic stabilizer.” Trans. Res. Rec. 1757: 50–57. https://doi.org/10.3141/1757-06.
Li, X. J. 2014. “Shrinkage cracking of soils and cementitiously-stabilized soils: Mechanisms and modeling.” Ph.D. thesis, Washington State Univ.
Little, D., S. Nair, and B. Herbert. 2010. “Addressing sulfate-induced heave in lime treated soils.” J. Geotech. Geoenviron. Eng. 136 (1): 110–118. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000185.
Martin-Alfonso, M., P. Partal, F. Navarro, M. GarcÃ-a-Morales, J. Bordado, and A. Diogo. 2009. “Effect of processing temperature on the bitumen/MDI-PEG reactivity.” Fuel Process. Technol. 90 (4): 525–530. https://doi.org/10.1016/j.fuproc.2009.01.007.
Mitchell, J. K. 1986. “Practical problems from surprising soil behavior.” J. Geotech. Eng. 112 (3): 255–289. https://doi.org/10.1061/(ASCE)0733-9410(1986)112:3(255).
Mohammed, A., and C. Vipulanandan. 2014. “Compressive and tensile behavior of polymer treated sulfate contaminated CL soil.” Geotech. Geol. Eng. 32 (1): 71–83. https://doi.org/10.1007/s10706-013-9692-9.
Moustafa, A., A. Bazaraa, and A. Nour El Din. 1981. “Soil stabilization by polymeric materials.” Macromol. Mater. Eng. 97 (1): 1–12. https://doi.org/10.1002/apmc.1981.050970101.
Naeini, S., and M. Ghorbanalizadeh. 2010. “Effect of wet and dry conditions on strength of silty sand soils stabilized with epoxy resin polymer.” J. Appl. Sci. 10 (22): 2839–2846. https://doi.org/10.3923/jas.2010.2839.2846.
Naeini, S. A., B. Naderinia, and E. Izadi. 2012. “Unconfined compressive strength of clayey soils stabilized with waterborne polymer.” J. Civ. Eng. 16 (6): 943–949. https://doi.org/10.1007/s12205-012-1388-9.
Ohama, Y. 1995. Handbook of polymer-modified concrete and mortars, 337–422. Park Ridge, NJ: Noyes Publications.
Onyejekwe, S., and G. Ghataora. 2014. “Soil stabilization using proprietary liquid chemical stabilizers: Sulphonated oil and a polymer.” Bull. Eng. Geol. Environ. 74 (2): 651–665. https://doi.org/10.1007/s10064-014-0667-8.
Puppala, A. J., N. Intharasombat, and R. Vempati. 2005. “Experimental studies on ettringite-induced heaving in soils.” J. Geotech. Geoenviron. Eng. 131 (3): 325–337. https://doi.org/10.1061/(ASCE)1090-0241(2005)131:3(325).
Rauch, A. F., J. S. Harmon, L. E. Katz, and H. M. Liljestrand. 2002. “Measured effects of liquid soil stabilizers on engineering properties of clay.” Transp. Res. Rec. 1787: 33–41. https://doi.org/10.3141/1787-04.
Rezaeimalek, S., J. Huang, and S. Bin-Shafique. 2017a. “Evaluation of curing method and mix design of a moisture activated polymer for sand stabilization.” Constr. Build. Mater. 146: 210–220. https://doi.org/10.1016/j.conbuildmat.2017.04.093.
Rezaeimalek, S., J. Huang, and S. Bin-Shafique. 2017b. “Performance of evaluation for polymer-stabilized soils.” Transp. Res. Rec. 2657: 58–66. https://doi.org/10.3141/2657-07.
Santoni, R. L., J. S. Tingle, and S. L. Webster. 2002. “Stabilization of silty-sand with nontraditional additives.” Transp. Res. Rec. 1787: 61–70. https://doi.org/10.3141/1787-07.
Sebesta, S., and T. Scullion. 2004. Effectiveness of minimizing reflective cracking in cement-treated bases by microcracking. Austin, TX: Texas Dept. of Transportation.
Sherwood, P. 1994. Soil stabilization with cement and lime. London: Stationary Office.
Sukmak, P., S. Horpibulsuk, and S.-L. Shen. 2013. “Strength development in clay-fly ash geopolymer.” Constr. Build. Mater. 40: 566–574. https://doi.org/.1016/j.conbuildmat.2012.11.015.
Zandieh, A. R., and S. S. Yasrobi. 2007. “Study of factors affecting the compressive strength of sandy soil stabilized with polymer.” Geotech. Geol. Eng. 28 (2): 139–145. https://doi.org/10.1007/s10706-009-9287-7.
Zhang, Z., W. Zhu, J. Zhang, and T. Tian. 2015. “Highly toughened poly (acrylonitrile styrene acrylic)/chlorinated polyethylene blends: Mechanical, rheological and thermal properties.” Polym. Test. 44: 23–29. https://doi.org/10.1016/j.polymertesting.2015.03.017.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Nov 1, 2017
Accepted: Feb 21, 2018
Published online: Jun 20, 2018
Published in print: Sep 1, 2018
Discussion open until: Nov 20, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.