Accelerated Corrosion Behavior of Steel in Concrete Subjected to Sustained Flexural Loading Using Electrochemical Methods and X-Ray Computed Tomography
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 7
Abstract
In this study, the effect of flexural loading on the chloride-induced corrosion behavior of steels in large-sized concrete was characterized using various electrochemical methods and X-ray computed tomography (X-CT). Electrochemical measurements revealed that steels embedded in loaded concrete exhibited higher corrosion rate than those in unloaded concrete after 15 days of accelerated corrosion. However, after accelerated corrosion for 60 days, similar corrosion behavior was identified for steels in both loaded concrete and unloaded concrete. It was found that the penetration and the distribution of corrosion products in concrete were significantly affected by the sustained flexural loading after the occurrence of load-induced transverse cracks.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors greatly acknowledge the support by the National Natural Science Foundation of China (No. 51678144), the National Basic Research Program of China “973 Project” (No. 2015CB655100) and the Natural Science Foundation of Jiangsu Province (BK20161420).
References
Ababneh, A., and M. Sheban. 2011. “Impact of mechanical loading on the corrosion of steel reinforcement in concrete structures.” Mater. Struct. 44 (6): 1123–1137. https://doi.org/10.1617/s11527-010-9688-3.
Andrade, C., L. Soler, and X. Nóvoa. 1995. “Advances in electrochemical impedance measurements in reinforced concrete.” Mater. Sci. Forum 192–194 (2): 843–856. https://doi.org/10.4028/www.scientific.net/MSF.192-194.843.
Angst, U., A. Rønnquist, B. Elsener, C. K. Larsen, and Ø. Vennesland. 2011. “Probabilistic considerations on the effect of specimen size on the critical chloride content in reinforced concrete.” Corros. Sci. 53 (1): 177–187. https://doi.org/10.1016/j.corsci.2010.09.017.
Bautista, A., E. Paredes, S. Alvarez, and F. Velasco. 2016. “Welded, sandblasted, stainless steel corrugated bars in non-carbonated and carbonated mortars: A 9-year corrosion study.” Corros. Sci. 102 (Jan): 363–372. https://doi.org/10.1016/j.corsci.2015.10.029.
Beck, M., J. Goebbels, and A. Burkert. 2007. “Application of X-ray tomography for the verification of corrosion processes in chloride contaminated mortar.” Mater. Corros. 58 (3): 207–210. https://doi.org/10.1002/maco.200604049.
Beck, M., J. Goebbels, A. Burkert, B. Isecke, and R. Bäßler. 2010. “Monitoring of corrosion processes in chloride contaminated mortar by electrochemical measurements and X-ray tomography.” Mater. Corros. 61 (6): 475–479. https://doi.org/10.1002/maco.200905364.
Berrocal, C. G., I. Löfgren, K. Lundgren, and L. Tang. 2015. “Corrosion initiation in cracked fibre reinforced concrete: Influence of crack width, fibre type and loading conditions.” Corros. Sci. 98 (Sep): 128–139. https://doi.org/10.1016/j.corsci.2015.05.021.
Česen, A., T. Kosec, and A. Legat. 2013. “Characterization of steel corrosion in mortar by various electrochemical and physical techniques.” Corros. Sci. 75 (Oct): 47–57. https://doi.org/10.1016/j.corsci.2013.05.015.
Dang, V. H., R. François, V. L’Hostis, and D. Meinel. 2015. “Propagation of corrosion in pre-cracked carbonated reinforced mortar.” Mater. Struct. 48 (8): 2575–2595. https://doi.org/10.1617/s11527-014-0338-z.
Darma, I. S., T. Sugiyama, and M. A. B. Promentilla. 2013. “Application of X-ray CT to study diffusivity in cracked concrete through the observation of tracer transport.” J. Adv. Concr. Technol. 11 (10): 266–281. https://doi.org/10.3151/jact.11.266.
Dong, B. Q., G. H. Fang, Y. Q. Liu, P. Dong, J. C. Zhang, F. Xing, and S. X. Hong. 2017. “Monitoring reinforcement corrosion and corrosion-induced cracking by X-ray microcomputed tomography method.” Cem. Concr. Res. 100 (Oct): 311–321. https://doi.org/10.1016/j.cemconres.2017.07.009.
Fukuda, D., Y. Nara, Y. Kobayashi, M. Maruyama, M. Koketsu, D. Hayashi, H. Ogawa, and K. Kaneko. 2012. “Investigation of self-sealing in high-strength and ultra-low-permeability concrete in water using micro-focus X-ray CT.” Cem. Concr. Res. 42 (11): 1494–1500. https://doi.org/10.1016/j.cemconres.2012.08.014.
Gallucci, E., K. Scrivener, A. Groso, M. Stampanoni, and G. Margaritondo. 2007. “3D experimental investigation of the microstructure of cement pastes using synchrotron X-ray microtomography (μCT).” Cem. Concr. Res. 37 (3): 360–368. https://doi.org/10.1016/j.cemconres.2006.10.012.
Gowripalan, N., V. Sirivivatnanon, and C. Lim. 2000. “Chloride diffusivity of concrete cracked in flexure.” Cem. Concr. Res. 30 (5): 725–730. https://doi.org/10.1016/S0008-8846(00)00216-7.
Han, J. D., W. Sun, G. H. Pan, and C. H. Wang. 2013. “Monitoring the evolution of accelerated carbonation of hardened cement pastes by X-ray computed tomography.” J. Mater. Civ. Eng. 25 (3): 347–354. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000610.
Islam, M., B. Bergsma, and C. Hansson. 2013. “Chloride-induced corrosion behavior of stainless steel and carbon steel reinforcing bars in sound and cracked concrete.” Corrosion 69 (3): 303–312. https://doi.org/10.5006/0706E.
Itty, P.-A., M. Serdar, C. Meral, D. Parkinson, A. A. MacDowell, D. Bjegović, and P. J. Monteiro. 2014. “In situ 3D monitoring of corrosion on carbon steel and ferritic stainless steel embedded in cement paste.” Corros. Sci. 83 (Jun): 409–418. https://doi.org/10.1016/j.corsci.2014.03.010.
Jaffer, S. J., and C. M. Hansson. 2008. “The influence of cracks on chloride-induced corrosion of steel in ordinary portland cement and high performance concretes subjected to different loading conditions.” Corros. Sci. 50 (12): 3343–3355. https://doi.org/10.1016/j.corsci.2008.09.018.
Jaffer, S. J., and C. M. Hansson. 2009. “Chloride-induced corrosion products of steel in cracked-concrete subjected to different loading conditions.” Cem. Concr. Res. 39 (2): 116–125. https://doi.org/10.1016/j.cemconres.2008.11.001.
Landis, E. N., and D. T. Keane. 2010. “X-ray microtomography.” Mater. Charact. 61 (12): 1305–1316. https://doi.org/10.1016/j.matchar.2010.09.012.
Lanzón, M., V. Cnudde, T. De Kock, and J. Dewanckele. 2012. “X-ray microtomography (μ-CT) to evaluate microstructure of mortars containing low density additions.” Cem. Concr. Compos. 34 (9): 993–1000. https://doi.org/10.1016/j.cemconcomp.2012.06.011.
Li, C. Q. 2000. “Corrosion initiation of reinforcing steel in concrete under natural salt spray and service loading-results and analysis.” ACI Mater. J. 97 (6): 690–697.
Li, G. P., F. J. Hu, and Y. X. Wu. 2011. “Chloride ion penetration in stressed concrete.” J. Mater. Civ. Eng. 23 (8): 1145–1153. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000281.
Li, L., and A. A. Sagüés. 2004. “Chloride corrosion threshold of reinforcing steel in alkaline solutions—Effect of specimen size.” Corrosion 60 (2): 195–202. https://doi.org/10.5006/1.3287721.
Masad, E., V. Jandhyala, N. Dasgupta, N. Somadevan, and N. Shashidhar. 2002. “Characterization of air void distribution in asphalt mixes using X-ray computed tomography.” J. Mater. Civ. Eng. 14 (2): 122–129. https://doi.org/10.1061/(ASCE)0899-1561(2002)14:2(122).
Michel, A., B. J. Pease, A. Peterová, M. R. Geiker, H. Stang, and A. E. A. Thybo. 2014. “Penetration of corrosion products and corrosion-induced cracking in reinforced cementitious materials: Experimental investigations and numerical simulations.” Cem. Concr. Compos. 47 (Mar): 75–86. https://doi.org/10.1016/j.cemconcomp.2013.04.011.
Michel, A., A. O. S. Solgaard, B. J. Pease, M. R. Geiker, H. Stang, and J. F. Olesen. 2013. “Experimental investigation of the relation between damage at the concrete-steel interface and initiation of reinforcement corrosion in plain and fibre reinforced concrete.” Corros. Sci. 77 (Dec): 308–321. https://doi.org/10.1016/j.corsci.2013.08.019.
Mien, T. V., B. Stitmannaithum, and T. Nawa. 2009. “Simulation of chloride penetration into concrete structures subjected to both cyclic flexural loads and tidal effects.” Comput. Concr. 6 (5): 421–435. https://doi.org/10.12989/cac.2009.6.5.421.
Montemor, M., M. Cunha, M. Ferreira, and A. Simoes. 2002. “Corrosion behaviour of rebars in fly ash mortar exposed to carbon dioxide and chlorides.” Cem. Concr. Compos. 24 (1): 45–53. https://doi.org/10.1016/S0958-9465(01)00025-7.
Montemor, M., A. Simoes, and M. Salta. 2000. “Effect of fly ash on concrete reinforcement corrosion studied by EIS.” Cem. Concr. Compos. 22 (3): 175–185. https://doi.org/10.1016/S0958-9465(00)00003-2.
Neff, D., J. Harnisch, M. Beck, V. L’Hostis, J. Goebbels, and D. Meinel. 2011. “Morphology of corrosion products of steel in concrete under macro-cell and self-corrosion conditions.” Mater. Corros. 62 (9): 861–871. https://doi.org/10.1002/maco.201005861.
Nóvoa, X. 2016. “Electrochemical aspects of the steel-concrete system: A review.” J. Solid State Electrochem. 20 (8): 2113–2125. https://doi.org/10.1007/s10008-016-3238-z.
Otieno, M., M. Alexander, and H.-D. Beushausen. 2010. “Corrosion in cracked and uncracked concrete-influence of crack width, concrete quality and crack reopening.” Mag. Concr. Res. 62 (6): 393–404. https://doi.org/10.1680/macr.2010.62.6.393.
Provis, J. L., R. J. Myers, C. E. White, V. Rose, and J. S. van Deventer. 2012. “X-ray microtomography shows pore structure and tortuosity in alkali-activated binders.” Cem. Concr. Res. 42 (6): 855–864. https://doi.org/10.1016/j.cemconres.2012.03.004.
Sangoju, B., R. G. Pillai, R. Gettu, B. Bharatkumar, and N. R. Iyer. 2015. “Use of portland pozzolana cement to enhance the service life of reinforced concrete exposed to chloride attack.” J. Mater. Civ. Eng. 27 (11): 04015031. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001293.
Šavija, B., M. Luković, S. A. S. Hosseini, J. Pacheco, and E. Schlangen. 2014. “Corrosion induced cover cracking studied by X-ray computed tomography, nanoindentation, and energy dispersive X-ray spectrometry (EDS).” Mater. Struct. 48 (7): 2043–2062. https://doi.org/10.1617/s11527-014-0292-9.
Scott, A., and M. Alexander. 2007. “The influence of binder type, cracking and cover on corrosion rates of steel in chloride-contaminated concrete.” Mag. Concr. Res. 59 (7): 495–505. https://doi.org/10.1680/macr.2007.59.7.495.
Shi, J. J., and G. Q. Geng. 2017. “Electrochemical behavior of fine-grained steel in alkaline solutions in the presence of chlorides.” J. Mater. Civ. Eng. 29 (7): 04017039. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001878.
Shi, J. J., J. Ming, W. Sun, and Y. M. Zhang. 2017. “Corrosion performance of reinforcing steel in concrete under simultaneous flexural load and chlorides attack.” Constr. Build. Mater. 149 (Sep): 315–326. https://doi.org/10.1016/j.conbuildmat.2017.05.092.
Shi, J. J., and W. Sun. 2010. “Evaluation of steel corrosion in concrete under simultaneous flexural load and chloride attacks.” [In Chinese.] J. Chin. Ceram. Soc. 38 (7): 1201–1208.
Subramaniam, K. V., and M. Bi. 2010. “Investigation of steel corrosion in cracked concrete: Evaluation of macrocell and microcell rates using Tafel polarization response.” Corros. Sci. 52 (8): 2725–2735. https://doi.org/10.1016/j.corsci.2010.04.030.
Sugiyama, T., M. Promentilla, T. Hitomi, and N. Takeda. 2010. “Application of synchrotron microtomography for pore structure characterization of deteriorated cementitious materials due to leaching.” Cem. Concr. Res. 40 (8): 1265–1270. https://doi.org/10.1016/j.cemconres.2009.10.009.
Sun, H. F., D. D. Zhao, Y. Gu, S. A. Memon, Z. L. Ren, B. Liu, X. G. Zhang, F. Xing, and D. W. Li. 2017. “Three-dimensional characterization of steel corrosion embedded in cement paste.” Constr. Build. Mater. 143 (Jul): 24–32. https://doi.org/10.1016/j.conbuildmat.2017.03.106.
Tang, F. J., X. M. Cheng, G. D. Chen, R. K. Brow, J. S. Volz, and M. L. Koenigstein. 2013. “Electrochemical behavior of enamel-coated carbon steel in simulated concrete pore water solution with various chloride concentrations.” Electrochim. Acta 92 (Mar): 36–46. https://doi.org/10.1016/j.electacta.2012.12.125.
Trejo, D., and R. G. Pillai. 2003. “Accelerated chloride threshold testing. I: ASTM A 615 and A 706 reinforcement.” ACI Mater. J. 100 (6): 519–527.
Vedalakshmi, R., and N. Palaniswamy. 2010. “Analysis of the electrochemical phenomenon at the rebar-concrete interface using the electrochemical impedance spectroscopic technique.” Mag. Concr. Res. 62 (3): 177–189. https://doi.org/10.1680/macr.2010.62.3.177.
Vidal, T., A. Castel, and R. François. 2007. “Corrosion process and structural performance of a 17 year old reinforced concrete beam stored in chloride environment.” Cem. Concr. Res. 37 (11): 1551–1561. https://doi.org/10.1016/j.cemconres.2007.08.004.
Wan, K. S., Q. Xu, Y. D. Wang, and G. H. Pan. 2014. “3D spatial distribution of the calcium carbonate caused by carbonation of cement paste.” Cem. Concr. Compos. 45 (Jan): 255–263. https://doi.org/10.1016/j.cemconcomp.2013.10.011.
Wan, K. S., and X. B. Xue. 2013. “In situ compressive damage of cement paste characterized by lab source X-ray computer tomography.” Mater. Charact. 82 (Aug): 32–40. https://doi.org/10.1016/j.matchar.2013.05.004.
Wang, J. Y., J. Dewanckele, V. Cnudde, S. Van Vlierberghe, W. Verstraete, and N. De Belie. 2014. “X-ray computed tomography proof of bacterial-based self-healing in concrete.” Cem. Concr. Compos. 53 (Oct): 289–304. https://doi.org/10.1016/j.cemconcomp.2014.07.014.
Wong, H. S., Y. X. Zhao, A. R. Karimi, N. R. Buenfeld, and W. L. Jin. 2010. “On the penetration of corrosion products from reinforcing steel into concrete due to chloride-induced corrosion.” Corros. Sci. 52 (7): 2469–2480. https://doi.org/10.1016/j.corsci.2010.03.025.
Yu, L. W., R. François, V. H. Dang, V. L’Hostis, and R. Gagné. 2015. “Development of chloride-induced corrosion in pre-cracked RC beams under sustained loading: Effect of load-induced cracks, concrete cover, and exposure conditions.” Cem. Concr. Res. 67 (Jan): 246–258. https://doi.org/10.1016/j.cemconres.2014.10.007.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: May 18, 2017
Accepted: Jan 12, 2018
Published online: Apr 27, 2018
Published in print: Jul 1, 2018
Discussion open until: Sep 27, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.