Design and Operation of a Real-Scale Electromagnetic Shielding Evaluation System for Reinforced Composite Construction Materials
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 8
Abstract
Electromagnetic noise due to undesirable interferences from electronic devices, infrastructures inherent to smart homes, buildings or cities, computer networks, or medical diagnostics has become a serious concern for the construction industry. A straightforward measuring system that allows one to determine the electromagnetic shielding of construction materials has been designed and implemented. Concrete or mortar panels containing reinforcing grids or diverse additives were fabricated and so characterized. The higher electromagnetic shielding values are obtained for panels containing over 15% metallic fibers and those reinforced with grids with a sieve area below . Depending on the type and percentage of additive or reinforcement included, frequency-dependent behaviors have been observed within the measured spectrum, which encompasses the frequency range used in modern communications systems. In addition, in order to demonstrate the capability of characterizing actual materials without any previous adaptation to the measuring technology requirements, commercial boards have been characterized as received.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to thank the “Junta de Comunidades de Castilla-La Mancha” for the financial support through the IDREU grant (PPII-2014-029-P).
References
Ahlbom, A., A. Green, L. Kheifets, D. Savitz, and A. Swerdlow. 2004. “Epidemiology of health effects of radiofrequency exposure.” Environ. Health Perspect. 112 (17): 1741–1754. https://doi.org/10.1289/ehp.7306.
Ameli, A., P. U. Jung, and C. B. Park. 2013. “Electrical properties and electromagnetic interference shielding effectiveness of polypropylene/carbon fiber composite foams.” Carbon 60 (Aug): 379–391. https://doi.org/10.1016/j.carbon.2013.04.050.
Asprone, D., D. Assante, A. Chiariello, G. Manfredi, G. Miano, A. Prota, and G. Rubinacci. 2010. “Assessment of the electromagnetic disturbance of a glass fiber reinforced composite fencing structure.” J. Compos. Constr. 14 (5): 629–635. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000121.
Bantsis, G., S. Mavridou, C. Sikalidis, M. Betsiou, N. Oikonomou, and T. Yioultsis. 2012. “Comparison of low cost shielding-absorbing cement paste building materials in X-band frequency range using a variety of wastes.” Ceram. Int. 38 (5): 3683–3692. https://doi.org/10.1016/j.ceramint.2012.01.010.
Bantsis, G., C. Sikalidis, M. Betsiou, T. Yioultsis, and A. Bourliva. 2011a. “Ceramic building materials for electromagnetic interference shielding using metallurgical slags.” Adv. Appl. Ceram. 110 (4): 233–237. https://doi.org/10.1179/1743676111Y.0000000009.
Bantsis, G., C. Sikalidis, M. Betsiou, T. Yioultsis, and T. Xenos. 2011b. “Electromagnetic absorption, reflection and interference shielding in X-band frequency range of low cost ceramic building bricks and sandwich type ceramic tiles using mill scale waste as an admixture.” Ceram. Int. 37 (8): 3535–3545. https://doi.org/10.1016/j.ceramint.2011.06.010.
Baoyi, L., D. Yuping, and L. Shunhua. 2012. “The electromagnetic characteristics of fly ash and absorbing properties of cement-based composites using fly ash as cement replacement.” Constr. Build. Mater. 27 (1): 184–188. https://doi.org/10.1016/j.conbuildmat.2011.07.062.
Burnett, J., and P. D. Yaping. 2002. “Mitigation of extremely low frequency magnetic fields from electrical installations in high-rise buildings.” Build. Environ. 37 (8–9): 769–775. https://doi.org/10.1016/S0360-1323(02)00043-4.
Cao, J., and D. D. L. Chung. 2003a. “Coke powder as an admixture in cement for electromagnetic interference shielding.” Carbon 41 (12): 2433–2436. https://doi.org/10.1016/S0008-6223(03)00289-6.
Cao, J., and D. D. L. Chung. 2003b. “Colloidal graphite as an admixture in cement and as a coating on cement for electromagnetic interference shielding.” Cem. Concr. Res. 33 (11): 1737–1740. https://doi.org/10.1016/S0008-8846(03)00152-2.
Cao, J. Y., and D. D. L. Chung. 2004. “Use of fly ash as an admixture for electromagnetic interference shielding.” Cem. Concr. Res. 34 (10): 1889–1892. https://doi.org/10.1016/j.cemconres.2004.02.003.
Chandrasekhar, P., and K. Naishadham. 1999. “Broadband microwave absorption and shielding properties of a poly(aniline).” Synth. Metals 105 (2): 115–120. https://doi.org/10.1016/S0379-6779(99)00085-5.
Chen, H. C., K. C. Lee, J. H. Lin, and M. Koch. 2007. “Comparison of electromagnetic shielding effectiveness properties of diverse conductive textiles via various measurement techniques.” J. Mater. Process. Technol. 192–193 (Oct): 549–554. https://doi.org/10.1016/j.jmatprotec.2007.04.023.
Chen, H. C., J. H. Lin, and K. C. Lee. 2008. “Electromagnetic shielding effectiveness of copper/stainless steel/polyamide fiber co-woven-knitted fabric reinforced polypropylene composites.” J. Reinf. Plast. Compos. 27 (2): 187–204. https://doi.org/10.1177/0731684407082628.
Chen, J., D. Zhao, H. Ge, and J. Wang. 2015. “Graphene oxide-deposited carbon fiber/cement composites for electromagnetic interference shielding application.” Constr. Build. Mater. 84: 66–72. https://doi.org/10.1016/j.conbuildmat.2015.03.050.
Chen, P.-H., and D. D. L. Chung. 2013. “Comparative evaluation of cement-matrix composites with distributed versus networked exfoliated graphite.” Carbon 63 (Nov): 446–453. https://doi.org/10.1016/j.carbon.2013.06.097.
Chiou, J.-M., Q. Zheng, and D. D. L. Chung. 1989. “Electromagnetic interference shielding by carbon fibre reinforced cement.” Composites 20 (4): 379–381. https://doi.org/10.1016/0010-4361(89)90663-0.
Choi, I., J. G. Kim, I. S. Seo, and D. G. Lee. 2012. “Radar absorbing sandwich construction composed of CNT, PMI foam and carbon/epoxy composite.” Compos. Struct. 94 (9): 3002–3008. https://doi.org/10.1016/j.compstruct.2012.04.009.
Choi, I., D. Lee, and D. G. Lee. 2014. “Hybrid composite low-observable radome composed of E-glass/aramid/epoxy composite sandwich construction and frequency selective surface.” Compos. Struct. 117 (Nov): 98–104. https://doi.org/10.1016/j.compstruct.2014.06.031.
Chou, C. K. 2007. “Thirty-five years in bioelectromagnetics research.” Bioelectromagnetics 28 (1): 3–15. https://doi.org/10.1002/bem.20292.
Chung, D. D. L. 2000. “Materials for electromagnetic interference shielding.” J. Mater. Eng Perform. 9 (3): 350–354. https://doi.org/10.1361/105994900770346042.
Chung, D. D. L. 2001a. “Comparison of submicron-diameter carbon filaments and conventional carbon fibers as fillers in composite materials.” Carbon 39 (8): 1119–1125. https://doi.org/10.1016/S0008-6223(00)00314-6.
Chung, D. D. L. 2001b. “Functional properties of cement-matrix composites.” J. Mater. Sci. 36 (6): 1315–1324. https://doi.org/10.1023/A:1017522616006.
Chung, D. D. L. 2012. “Carbon materials for structural self-sensing, electromagnetic shielding and thermal interfacing.” Carbon 50 (9): 3342–3353. https://doi.org/10.1016/j.carbon.2012.01.031.
Cucurachi, S., W. L. M. Tamis, M. G. Vijver, W. J. G. M. Peijnenburg, J. F. B. Bolte, and G. R. de Snoo. 2013. “A review of the ecological effects of radiofrequency electromagnetic fields (RF-EMF).” Environ. Int. 51 (Jan): 116–140. https://doi.org/10.1016/j.envint.2012.10.009.
Dalke, R. A., C. L. Holloway, P. McKenna, M. Johansson, and A. S. Ali. 2000. “Effects of reinforced concrete structures on RF communications.” IEEE Trans. Electromagn. Compat. 42 (4): 486–496. https://doi.org/10.1109/15.902318.
Dhawan, S. K., N. Singh, and S. Venkatachalam. 2002. “Shielding behaviour of conducting polymer-coated fabrics in X-band, W-band and radio frequency range.” Synth. Met. 129 (3): 261–267. https://doi.org/10.1016/S0379-6779(02)00079-6.
Dou, Z., G. Wu, X. Huang, D. Sun, and L. Jiang. 2007. “Electromagnetic shielding effectiveness of aluminum alloy-fly ash composites.” Composites Part A 38 (1): 186–191. https://doi.org/10.1016/j.compositesa.2006.01.015.
Drinovsky, J., and Z. Kejik. 2009. “Electromagnetic shielding efficiency measurement of composite materials.” Meas. Sci. Rev. 9 (4): 109–112.
Fu, X., and D. D. L. Chung. 1996. “Submicron carbon filament cement-matrix composites for electromagnetic interference shielding.” Cem. Concr. Res. 26 (10): 1467–1472. https://doi.org/10.1016/0008-8846(96)00146-9.
Fu, X., and D. D. L. Chung. 1998a. “Radio-wave-reflecting concrete for lateral guidance in automatic highways.” Cem. Concr. Res. 28 (6): 795–801. https://doi.org/10.1016/S0008-8846(98)00057-X.
Fu, X. L., and D. D. L. Chung. 1998b. “Submicron-diameter-carbon-filament cement-matrix composites.” Carbon 36 (4): 459–462. https://doi.org/10.1016/S0008-6223(98)90017-3.
Geetha, S., K. K. S. Kumar, C. R. K. Rao, M. Vijayan, and D. C. Trivedi. 2009. “EMI shielding: Methods and materials—A review.” J. Appl. Polym. Sci. 112 (4): 2073–2086. https://doi.org/10.1002/app.29812.
Gregory, R., and D. von Winterfeldt. 1996. “The effects of electromagnetic fields from transmission lines on public fears and property values.” J. Environ. Manage. 48 (3): 201–214. https://doi.org/10.1006/jema.1996.0073.
Guan, H., S. Liu, and Y. Duan. 2007. “Expanded polystyrene as an admixture in cement-based composites for electromagnetic absorbing.” J. Mater. Eng. Perform. 16 (1): 68–72. https://doi.org/10.1007/s11665-006-9010-2.
Guan, H. T., S. H. Liu, Y. P. Duan, and J. Cheng. 2006. “Cement based electromagnetic shielding and absorbing building materials.” Cem. Concr. Compos. 28 (5): 468–474. https://doi.org/10.1016/j.cemconcomp.2005.12.004.
Haddad, R. H., and I. L. Al-Qadi. 1998. “Characterization of portland cement concrete using electromagnetic waves over the microwave frequencies.” Cem. Concr. Res. 28 (10): 1379–1391. https://doi.org/10.1016/S0008-8846(98)00076-3.
Hakansson, E., A. Amiet, and A. Kaynak. 2006. “Electromagnetic shielding properties of polypyrrole/polyester composites in the 1-18 GHz frequency range.” Synth. Met. 156 (14–15): 917–925.
Hutagalung, S. D., N. H. Sahrol, Z. A. Ahmad, M. F. Ain, and M. Othman. 2012. “Effect of additive on the dielectric and electromagnetic interference shielding properties of sintered cement-based ceramics.” Ceram. Int. 38 (1): 671–678. https://doi.org/10.1016/j.ceramint.2011.07.055.
Hyun, S.-Y., J.-K. Du, H.-J. Lee, K.-W. Lee, J.-H. Lee, C. Jung, E.-J. Kim, W. Kim, and J.-G. Yook. 2014. “Analysis of shielding effectiveness of reinforced concrete against high-altitude electromagnetic pulse.” IEEE Trans. Electromagn. Compat. 56 (6): 1488–1496. https://doi.org/10.1109/TEMC.2014.2322911.
Hyun, S.-Y., K.-W. Lee, and J.-G. Yook. 2012. “Modeling of shielding effectiveness of reinforced concrete walls for electromagnetic pulse.” In 2012 9th European Radar Conf. (EuRAD), 453–456. New York: IEEE.
Irigaray, P., J. A. Newby, R. Clapp, L. Hardell, V. Howard, L. Montagnier, S. Epstein, and D. Belpomme. 2007. “Lifestyle-related factors and environmental agents causing cancer: An overview.” Biomed. Pharmacother. 61 (10): 640–658. https://doi.org/10.1016/j.biopha.2007.10.006.
Ishii, N., M. Miyakawa, and K. Sakai. 2005. “A method for achieving electromagnetic wave absorption by low-loss stratified construction materials.” IEEE Trans. Electromagn. Compat. 47 (1): 105–111. https://doi.org/10.1109/TEMC.2004.842105.
Ishikawa, R., F. Amemiya, N. Nakashio, T. Nishimura, and N. Kuwabara. 2006. “Method of evaluating shielding effect for electronic equipment case using wire grid model and radiation source from 1 GHz to 3 GHz.” In 2006 IEEE Int. Symp. on Electromagnetic Compatibility, 2006. EMC 2006. New York: IEEE.
Jou, W. S., H. Z. Cheng, and C. F. Hsu. 2007. “The electromagnetic shielding effectiveness of carbon nanotubes polymer composites.” J. Alloys Compd. 434–435 (May): 641–645. https://doi.org/10.1016/j.jallcom.2006.08.203.
Khushnood, R. A., S. Ahmad, P. Savi, J. M. Tulliani, M. Giorcelli, and G. A. Ferro. 2015. “Improvement in electromagnetic interference shielding effectiveness of cement composites using carbonaceous nano/micro inerts.” Constr. Build. Mater. 85 (Jun): 208–216. https://doi.org/10.1016/j.conbuildmat.2015.03.069.
Kim, P. C., and D. G. Lee. 2009. “Composite sandwich constructions for absorbing the electromagnetic waves.” Compos. Struct. 87 (2): 161–167. https://doi.org/10.1016/j.compstruct.2008.05.015.
Kim, S. W., Y. W. Yoon, S. J. Lee, G. Y. Kim, Y. B. Kim, Y. Y. Chun, and K. S. Lee. 2007. “Electromagnetic shielding properties of soft magnetic powder-polymer composite films for the application to suppress noise in the radio frequency range.” J. Magn. Magn. Mater. 316 (2): 472–474. https://doi.org/10.1016/j.jmmm.2007.03.133.
Krewski, D., C. V. Byus, B. W. Glickman, W. G. Lotz, R. Mandeville, M. L. McBride, F. S. Prato, and D. F. Weaver. 2001. “Potential health risks of radiofrequency fields from wireless telecommunication devices.” J. Toxicol. Environ. Health Part B 4 (1): 1–143. https://doi.org/10.1080/109374001459458.
Metwally, I. A., W. J. Zischank, and F. H. Heidler. 2004. “Measurement of magnetic fields inside single- and double-layer reinforced concrete buildings during simulated lightning currents.” IEEE Trans. Electromagn. Compat. 46 (2): 208–221. https://doi.org/10.1109/TEMC.2004.826894.
Micheli, D., A. Delfini, F. Santoni, F. Volpini, and M. Marchetti. 2015. “Measurement of electromagnetic field attenuation by building walls in the mobile phone and satellite navigation frequency bands.” IEEE Antennas Wirel. Propag. Lett. 14: 698–702. https://doi.org/10.1109/LAWP.2014.2376811.
Micheli, D., R. Pastore, A. Vricella, R. B. Morles, M. Marchetti, A. Delfini, F. Moglie, and V. M. Primiani. 2014. “Electromagnetic characterization and shielding effectiveness of concrete composite reinforced with carbon nanotubes in the mobile phones frequency band.” Mater. Sci. Eng. B 188 (Oct): 119–129. https://doi.org/10.1016/j.mseb.2014.07.001.
Min, L., J. L. Drewniak, S. Radu, J. Nuebel, T. H. Hubing, R. E. DuBroff, and T. P. Van Doren. 2001. “An EMI estimate for shielding-enclosure evaluation.” IEEE Trans. Electromagn. Compat. 43 (3): 295–304. https://doi.org/10.1109/15.942602.
Muthusamy, S., and D. D. L. Chung. 2010. “Carbon-fiber cement-based materials for electromagnetic shielding.” ACI Mater. J. 107 (6): 602–610.
Nam, I. W., H. K. Kim, and H. K. Lee. 2012. “Influence of silica fume additions on electromagnetic interference shielding effectiveness of multi-walled carbon nanotube/cement composites.” Constr. Build. Mater. 30 (May): 480–487. https://doi.org/10.1016/j.conbuildmat.2011.11.025.
Ogunsola, A., U. Reggiani, and L. Sandrolini. 2005. “Shielding effectiveness of concrete buildings.” In IEEE 6th Int. Symp. on Electromagnetic Compatibility and Electromagnetic Ecology, 65–68. New York: IEEE.
Ogunsola, A., U. Reggiani, and L. Sandrolini. 2006. “Modelling shielding properties of concrete.” In 17th Int. Zurich Symp. on Electromagnetic Compatibility, 2006. EMC-Zurich 2006. New York: IEEE.
Park, K. Y., S. E. Lee, C. G. Kim, and J. H. Han. 2006. “Fabrication and electromagnetic characteristics of electromagnetic wave absorbing sandwich structures.” Compos. Sci. Technol. 66 (3–4): 576–584. https://doi.org/10.1016/j.compscitech.2005.05.034.
Park, K.-Y., S.-E. Lee, C.-G. Kim, and J.-H. Han. 2007. “Application of MWNT-added glass fabric/epoxy composites to electromagnetic wave shielding enclosures.” Compos. Struct. 81 (3): 401–406. https://doi.org/10.1016/j.compstruct.2006.08.029.
Pastor, J. M., L. D. García, S. Quintana, and J. Peña. 2014. “Glass reinforced concrete panels containing recycled tyres: Evaluation of the acoustic properties of for their use as sound barriers.” Constr. Build. Mater. 54 (Jun): 541–549. https://doi.org/10.1016/j.conbuildmat.2013.12.040.
Pastore, R., D. Micheli, A. Vricella, R. B. Morles, M. Marchetti, F. Moglie, and V. M. Primiani. 2015. “Advanced concrete materials for EMI reduction in protected environment and IEMI threats suppression.” In 2015 IEEE 15th Int. Conf. on Environment and Electrical Engineering (EEEIC), 2011–2016. New York: IEEE.
Pozar, D. M. 1997. Microwave engineering. 2nd ed. New York: Wiley.
Razavi, S. M. J., and M. Khalaj-Amirhosseini. 2010. “Optimum design of electromagnetic shielding rooms with minimum usage of absorbing materials.” Int. J. RF Microwave Comput. Aided Eng. 20 (1): 22–32.
Rodrigues, F. A., and I. Joekes. 2011. “Cement industry: Sustainability, challenges and perspectives.” Environ. Chem. Lett. 9 (2): 151–166. https://doi.org/10.1007/s10311-010-0302-2.
Röösli, M. 2008. “Radiofrequency electromagnetic field exposure and non-specific symptoms of ill health: A systematic review.” Environ. Res. 107 (2): 277–287. https://doi.org/10.1016/j.envres.2008.02.003.
Ropiak, C. A., M. McQuage, and W. Padilla-Vargas. 2009. Electromagnetic field distribution as a function of building materials—Revisiting the standard definition of shielding effectiveness. New York: IEEE.
Rothman, K. J. 2000. “Epidemiological evidence on health risks of cellular telephones.” Lancet 356 (9244): 1837–1840. https://doi.org/10.1016/S0140-6736(00)03244-X.
Sandrolini, L., U. Reggiani, and A. Ogunsola. 2007. “Modelling the electrical properties of concrete for shielding effectiveness prediction.” J. Phys. D Appl. Phys. 40 (17): 5366–5372. https://doi.org/10.1088/0022-3727/40/17/053.
Sato, H., H. Domae, M. Takahashi, and M. Abe. 2000. “Reflection and transmission control of electromagnetic wave for concrete walls.” Electron. Commun. Japan Part I-Electron. 83 (11): 12–21. https://doi.org/10.1002/1520-6432(200011)83:11%3C12::AID-ECJB2%3E3.0.CO;2-E.
Sato, H., M. Takahashi, and M. Abe. 2002. “Absorption of electromagnetic waves by dome-shaped concrete walls.” Electron. Commun. Japan Part I-Commun. 85 (10): 33–43. https://doi.org/10.1002/ecja.1129.
Savage, E. B., J. L. Gilbert, W. A. Radasky, and M. J. Madrid. 2010. “An alternative EM shielding effectiveness measurement method for buildings.” In 2010 Asia-Pacific Symp. on Electromagnetic Compatibility (APEMC), 138–141. New York: IEEE.
Sedlacik, M., M. Mrlik, V. Babayan, and V. Pavlinek. 2016. “Magnetorheological elastomers with efficient electromagnetic shielding.” Compos. Struct. 135 (Jan): 199–204. https://doi.org/10.1016/j.compstruct.2015.09.037.
Shi, Z. Q., and D. D. L. Chung. 1995. “Concrete for magnetic shielding (Vol 25 (5), PG 939-944, 1995).” Cement Concr. Res. 25 (6): 1380.
Singh, A. P., B. K. Gupta, M. Mishra, A. Chandra, R. B. Mathur, and S. K. Dhawan. 2013. “Multiwalled carbon nanotube/cement composites with exceptional electromagnetic interference shielding properties.” Carbon 56 (May): 86–96. https://doi.org/10.1016/j.carbon.2012.12.081.
Singh, A. P., M. Mishra, A. Chandra, and S. K. Dhawan. 2011. “Graphene oxide/ferrofluid/cement composites for electromagnetic interference shielding application.” Nanotechnology 22 (46): 465701. https://doi.org/10.1088/0957-4484/22/46/465701.
Thomassin, J.-M., C. Jérⓞme, T. Pardoen, C. Bailly, I. Huynen, and C. Detrembleur. 2013. “Polymer/carbon based composites as electromagnetic interference (EMI) shielding materials.” Mater. Sci. Eng. R Rep. 74 (7): 211–232. https://doi.org/10.1016/j.mser.2013.06.001.
von Klemperer, C. J., and D. Maharaj. 2009. “Composite electromagnetic interference shielding materials for aerospace applications.” Compos. Struct. 91 (4): 467–472. https://doi.org/10.1016/j.compstruct.2009.04.013.
Wang, B., Z. Guo, Y. Han, and T. Zhang. 2013. “Electromagnetic wave absorbing properties of multi-walled carbon nanotube/cement composites.” Constr. Build. Mater. 46 (Sep): 98–103. https://doi.org/10.1016/j.conbuildmat.2013.04.006.
Wang, L. B., K. Y. See, Y. Ling, and W. J. Koh. 2012. “Study of metal foams for architectural electromagnetic shielding.” J. Mater. Civ. Eng. 24 (4): 488–493. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000403.
Wang, L.-L., B.-K. Tay, K.-Y. See, Z. Sun, L.-K. Tan, and D. Lua. 2009. “Electromagnetic interference shielding effectiveness of carbon-based materials prepared by screen printing.” Carbon 47 (8): 1905–1910. https://doi.org/10.1016/j.carbon.2009.03.033.
Wang, Z.-J., K.-Z. Li, and Wang, C. 2014. “Freezing-thawing effects on electromagnetic wave reflectivity of carbon fiber cement based composites.” Constr. Build. Mater. 64 (Aug): 288–292. https://doi.org/10.1016/j.conbuildmat.2014.04.091.
Wen, S. H., and D. D. L. Chung. 2004. “Electromagnetic interference shielding reaching 70 dB in steel fiber cement.” Cem. Concr. Res. 34 (2): 329–332. https://doi.org/10.1016/j.cemconres.2003.08.014.
Zhang, X., and W. Sun. 2010. “Microwave absorbing properties of double-layer cementitious composites containing Mn-Zn ferrite.” Cem. Concr. Compos. 32 (9): 726–730. https://doi.org/10.1016/j.cemconcomp.2010.07.013.
Zhao, Z. B., X. Cui, L. Li, and C. Z. Gao. 2008. “Analysis of shielding performance of reinforced concrete structures using the method of moments.” IEEE Trans. Magn. 44 (6): 1474–1477. https://doi.org/10.1109/TMAG.2007.916243.
Zhou, B., C. Gao, B. Chen, and Z. Chen. 2000. “Experimental investigation of EMP shielding effectiveness of reinforced-concrete cell model.” In Proc., Asia-Pacific Conf. on Environmental Electromagnetics, 2000. CEEM 2000, 296–300. New York: IEEE.
Zornoza, E., G. Catala, F. Jimenez, L. G. Andion, and P. Garces. 2010. “Electromagnetic interference shielding with portland cement paste containing carbon materials and processed fly ash.” Materiales De Construccion 60 (300): 21–32. https://doi.org/10.3989/mc.2010.51009.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Sep 28, 2017
Accepted: Jan 9, 2018
Published online: May 24, 2018
Published in print: Aug 1, 2018
Discussion open until: Oct 24, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.