Influence of Dispersion Methods on Sulfate Resistance of Nanosilica-Contained Mortars
Publication: Journal of Materials in Civil Engineering
Volume 29, Issue 7
Abstract
This study evaluates the influence of various dispersion methods on the sulfate attack resistance of nanosilica (nS)-contained mortars. Multiple mechanical or ultrasonic dispersion methods, high-range water-reducing admixtures (HRWRA) dosing procedures, and both dry and aqueous solution forms of nS were used to prepare a series of mortars with 0, 3, and 6% replacement of portland cement with nS. Mortars were subjected to 6 months of exposure in a 5% sodium sulfate solution. Expansion, compressive strength, water absorption, rapid sulfate ion permeability, and porosity were measured. Results indicated that use of the aqueous form of nS results in a more sulfate resistant and impermeable mortar than all other tested methods of dry form nS. High-range water-reducing admixtures dosage proved most effective when added directly to the mixer after all water, binders, and fine aggregate were combined. Excessive ultrasonic dispersion of dry nS in the mixing water may cause further agglomeration of the nS that proved deleterious to permeability and sulfate resistance. In terms of compressive strength, mortars with 3% nS content performed similarly to those with double the nS content. Increasing the nS content seemed to have the least influence on the compressive strength of the better dispersed aqueous nS mixtures.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASTM. (2012). “Standard test method for electrical indication of concrete’s ability to resist chloride ion penetration.” ASTM C1202/C1202M-12, ASTM International, West Conshohocken, PA.
ASTM. (2013). “Standard test method for density, absorption, and voids in hardened concrete.” ASTM C642-13, ASTM International, West Conshohocken, PA.
ASTM. (2014a). “Standard practice for mechanical mixing of hydraulic cement pastes and mortars of plastic consistency.” ASTM C305-14, ASTM International, West Conshohocken, PA.
ASTM. (2014b). “Standard specification for flow table for use in tests of hydraulic cement.” ASTM C230/C230M-14, ASTM International, West Conshohocken, PA.
ASTM. (2015a). “Standard test method for flow of hydraulic cement mortar.” ASTM C1437-15, ASTM International, West Conshohocken, PA.
ASTM. (2015b). “Standard test method for length change of hydraulic-cement mortars exposed to a sulfate solution.” ASTM C1012/C1012M-15, ASTM International, West Conshohocken, PA.
ASTM. (2016a). “Standard practice for making and curing concrete test specimens in the laboratory.” ASTM C192/C192M-16a, ASTM International, West Conshohocken, PA.
ASTM. (2016b). “Standard specification for concrete aggregates.” ASTM C33/C33M-16e1, ASTM International, West Conshohocken, PA.
ASTM. (2016c). “Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens).” ASTM C109/C109M-16a, ASTM International, West Conshohocken, PA.
Berra, M., Carassiti, F., Mangialardi, T., Paolini, A. E., and Sebastiani, M. (2012). “Effects of nanosilica addition on workability and compressive strength of portland cement pastes.” Constr. Build. Mater., 35(10), 666–675.
Campillo, I., Dolado, J. S., and Porro, A. (2004). “High-performance nanoestructured materials for construction.” Nanotechnology in construction, W. Z. Peter, J. M. Bartos, J. J. Hughes, and P. Trtik, eds., Royal Society of Chemistry, London, 215–225.
CCAA (Cement Concrete & Aggregates Australia). (2011). “Technical note: Sulfate-resisting concrete.” Australia.
Choolaei, M., Rashidi, A. M., Ardjmand, M., Yadegari, A., and Soltanian, H. (2012). “The effect of nanosilica on the physical properties of oil well cement.” Mater. Sci. Eng.: A, 538(3), 288–294.
Dolado, J. S., et al. (2007). “Effect of nanosilica additions on belite cement pastes held in sulfate solutions.” J. Am. Ceram. Soc., 90(12), 3973–3976.
Du, H., Du, S., and Liu, X. (2014). “Durability performances of concrete with nano-silica.” Constr. Build. Mater., 73(12), 705–712.
Ghafoori, N., Batilov, I. B., and Najimi, M. (2016). “Sulfate resistance of nanosilica and microsilica contained mortars.” ACI Mater. J., 113(4), 459–469.
Hou, P., Kawashima, S., Kong, D., Corr, D. J., Qian, J., and Shah, S. P. (2013a). “Modification effects of colloidal nanoSiO2 on cement hydration and its gel property.” Compos. Part B: Eng., 45(1), 440–448.
Hou, P., Kawashima, S., Wang, K., Corr, D. J., Qian, J., and Shah, S. P. (2013b). “Effects of colloidal nanosilica on rheological and mechanical properties of fly ash-cement mortar.” Cem. Concr. Compos., 35(1), 12–22.
Jiang, J., Oberdörster, G., and Biswas, P. (2009). “Characterization of size, surface charge, and agglomeration state of nanoparticle dispersions for toxicological studies.” J. Nanoparticle Res., 11(1), 77–89.
Jo, B.-W., Kim, C.-H., Tae, G., and Park, J.-B. (2007). “Characteristics of cement mortar with nano-SiO2 particles.” Constr. Build. Mater., 21(6), 1351–1355.
Kawashima, S., Hou, P., Corr, D. J., and Shah, S. P. (2013). “Modification of cement-based materials with nanoparticles.” Cem. Concr. Compos., 36(1), 8–15.
Khanzadi, M., Tadayon, M., Sepehri, H., and Sepehri, M. (2010). “Influence of nano-silica particles on mechanical properties and permeability of concrete.” 2nd Int. Conf. on Sustainable Construction Materials and Technologies, J. Zachar, P. Claisse, T. R. Naik, and E. Ganjian, eds., Coventry Univ., Coventry, U.K.
Koohdaragh, M., and Mohamadi, H. H. (2011). “Comparison of mechanical of the concrete samples containing micro-silica and nano-silica.” Aust. J. Basic Appl. Sci., 5(10), 560–563.
Kosmatka, S. H., Kerkhoff, B., and Panarese, W. C. (2002). Design and control of concrete mixtures, Portland Cement Association, Skokie, IL.
Li, H., Xiao, H., Yuan, J., and Ou, J. (2004). “Microstructure of cement mortar with nano-particles.” Compos. Part B: Eng., 35(2), 185–189.
Mann. (2006). “Report on nanotechnology and construction.” Institute of Nanotechnology, U.K.
Mehta, P. K. (1975). “Evaluation of sulfate-resisting cements by a new test method.” J. Proc., 72(10), 573–575.
Mehta, P. K., and Mehta, P. K. (1993). “Sulfate attack on concrete—A critical review.” Materials science of concrete III, J., Skalny, ed., American Ceramic Society, Westerville, OH, 105–127.
Mindess, S., Young, F. J., and Darwin, D. (2003). Concrete, 2nd Ed., Pearson Education, Inc., Upper Saddle River, NJ.
Mondal, P., Shah, S., Marks, L., and Gaitero, J. (2010). “Comparative study of the effects of microsilica and nanosilica in concrete.” Transp. Res. Rec., 2141(2141), 6–9.
Nili, M., Ehsani, A., and Shabani, K. (2010). “Influence of nano-SiO 2 and microsilica on concrete performance.” Proc., 2nd Int. Conf. on Sustainable Construction Materials and Technologies, J. Zachar, P. Claisse, T. R. Naik, and E. Ganjian, eds., Coventry Univ., Coventry, U.K.
Park, C. K., Noh, M. H., and Park, T. H. (2005). “Rheological properties of cementitious materials containing mineral admixtures.” Cem. Concr. Res., 35(5), 842–849.
Richardson, M. G. (2002). Fundamentals of durable reinforced concrete, Spon Press, New York.
Rundong, G., Qingbin, L., Shunbo, Z., and Xiaoming, Y. (2010). “Deterioration mechanisms of sulfate attack on concrete under alternate action.” J. Wuhan Univ. Technol. Mater. Sci. Ed., 25(2), 355–359.
Sahin, R., and Oltulu, M. (2008). “New materials for concrete technology: Nano powders.” 33rd Conf. on Our World in Concrete and Structures, Singapore Concrete Institute, Singapore.
Said, A. M., Zeidan, M. S., Bassuoni, M. T., and Tian, Y. (2012). “Properties of concrete incorporating nano-silica.” Constr. Build. Mater., 36(11), 838–844.
Sanchez, F., and Sobolev, K. (2010). “Nanotechnology in concrete—A review.” Constr. Build. Mater., 24(11), 2060–2071.
Senff, L., Hotza, D., Repette, W. L., Ferreira, V. M., and Labrincha, J. A. (2010a). “Effect of nanosilica and microsilica on microstructure and hardened properties of cement pastes and mortars.” Adv. Appl. Ceram., 109(2), 104–110.
Senff, L., Hotza, D., Repette, W. L., Ferreira, V. M., and Labrincha, J. A. (2010b). “Mortars with nano-SiO2 and micro-SiO2 investigated by experimental design.” Constr. Build. Mater., 24(8), 1432–1437.
Singh, L. P., Karade, S. R., Bhattacharyya, S. K., Yousuf, M. M., and Ahalawat, S. (2013). “Beneficial role of nanosilica in cement based materials—A review.” Constr. Build. Mater., 47(10), 1069–1077.
Taurozzi, J. S., Hackley, V. A., and Wiesner, M. R. (2011). “Ultrasonic dispersion of nanoparticles for environmental, health and safety assessment—Issues and recommendations.” Nanotoxicology, 5(4), 711–729.
Tobón, J. I., Payá, J., and Restrepo, O. J. (2015). “Study of durability of Portland cement mortars blended with silica nanoparticles.” Constr. Build. Mater., 80(4), 92–97.
Tobón, J. I., Restrepo, O. J., and Payá, J. (2010). “Comparative analysis of performance of portland cement blended with nanosilica and silica fume.” Dyna (Medellin, Colombia), 77(163), 37–46.
Vasylkiv, O., and Sakka, Y. (2001). “Synthesis and colloidal processing of zirconia nanopowder.” J. Am. Ceram. Soc., 84(11), 2489–2494.
Winter, N. B. (2012). “Understanding cement.” WHD Microanalysis Consultants Ltd., Woodridge, U.K.
Zaki, S. I., and Ragab, K. S. (2009). “How nanotechnology can change concrete.” 1st Int. Conf. on Sustainable Built Environment Infrastructures in Developing Countries, ENSET, Oran, Algeria, 407–414.
Zapata, L. E., Portela, G., Suárez, O. M., and Carrasquillo, O. (2013). “Rheological performance and compressive strength of superplasticized cementitious mixtures with micro/nano-SiO2 additions.” Constr. Build. Mater., 41(4), 708–716.
Zhang, M.-H., Islam, J., and Peethamparan, S. (2012). “Use of nano-silica to increase early strength and reduce setting time of concretes with high volumes of slag.” Cem. Concr. Compos., 34(5), 650–662.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 29 • Issue 7 • July 2017
Copyright
©2017 American Society of Civil Engineers.
History
Received: Apr 12, 2016
Accepted: Nov 3, 2016
Published ahead of print: Mar 26, 2017
Published online: Mar 27, 2017
Published in print: Jul 1, 2017
Discussion open until: Aug 27, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.