Effect of Formwork Characteristics on SCC Lateral Pressure
Publication: Journal of Materials in Civil Engineering
Volume 29, Issue 5
Abstract
Lateral pressure exerted on vertical formwork by fresh self-consolidating concrete (SCC) controls its design. Several factors, including material properties, placement conditions, and formwork characteristics, can affect formwork pressure. This paper presents the influence of formwork width (0.20–1.0 m), shape (circular versus square), and surface material (PVC, plywood, steel, and polyester filter membrane) of formwork on lateral pressure characteristics. The diameter of the pressure sensor used to evaluate lateral pressure characteristics is also investigated. The results showed that the increase in formwork width can increase the initial lateral pressure and delay the time needed for the formwork removal. Correction factors accounting for the changes in the formwork width on the initial pressure and pressure decay were developed. The formwork surface materials did show significant effect on initial formwork pressure, and different pressure decay responses were observed for each formwork material. The longest time for pressure cancellation was obtained for the steel formwork, and the shortest one for the polyester filter membrane.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge the financial support of the National Ready-Mix Concrete Education Research Foundation and the Strategic Development Council (SDC) of the American Concrete Institute (ACI), and member companies of SDC.
References
ACI (American Concrete Institute). (2007). “Guide to formwork for concrete.” ACI 347R-03, Farmington Hills, MI.
Arslan, M., (2002). “Effects of drainer formworks on concrete lateral pressure.” Const. Build. Mater., 16(5), 253–259.
Arslan, M., Simsek, O., and Subasi, S. (2005). “Effects of formwork surface materials on concrete lateral pressure.” Constr. Build Mater., 19(4), 319–325.
Assaad, J. J., and Khayat, K. H. (2005a). “Effect of coarse aggregate characteristics on lateral pressure exerted by self-consolidating concrete.” ACI Mater. J., 102(3), 145–153.
Assaad, J. J., and Khayat, K. H. (2005b). “Kinetics of formwork pressure drop of self-consolidating concrete containing various types and contents of binder.” Cem. Concr. Res., 35(8), 1522–1530.
Assaad, J. J., and Khayat, K. H. (2006a). “Effect of casting rate and concrete temperature on formwork pressure of self-consolidating concrete.” Mater. Struct., 39(3), 333–341.
Assaad, J. J., and Khayat, K. H. (2006b). “Effect of mixture consistency on formwork pressure exerted by highly flowable concrete.” J. Mater. Civ. Eng., 786–791.
Assaad, J. J., and Khayat, K. H. (2006c). “Effect of viscosity-enhancing admixtures on formwork pressure and thixotropy of self-consolidating concrete.” ACI Mater. J., 103(4), 280–287.
Assaad, J. J., Khayat, K. H., and Mesbah, H. (2003). “Variation of formwork pressure with thixotropy of self-consolidating concrete.” ACI Mater. J., 100(1), 29–37.
Beitzel, M. (2010). “Modeling fresh concrete pressure of normal and self-compacting concrete.” Design, Production and Placement of Self-Consolidating Concrete, Vol. 1, Springer, Netherlands, 243–254.
Billberg, P., Silfwerbrand, J., and Österberg, T. (2005). “Form pressures generated by self-consolidating concrete. casting rate is a dominant factor.” ACI Concr. Int., 27(10), 35–42.
CIRIA (Civil Industries Research and Information Association). (1985). “Concrete pressure on formwork.”, London.
CSA (Canadian Standards Association). (2015). “Concrete materials and methods of concrete construction/test methods and standard practices for concrete.” CSA-A23.1, Canadian Standards Association, Toronto.
Djelal, C. (2001). “Designing and perfecting a tribometer for the study of friction of a concentrated clay-water mixture against a metallic surface.” Mater. and Struct., 34(1), 51–58.
Djelal, C., Vanhove, Y., and Magnin, A. (2004). “Tribological behaviour of self-compacting concrete.” Cem. and Concr. Res., 34(5), 821–828.
Gardner, N. J., and Ho, PT.-J. (1979). “Lateral pressure of fresh concrete.” ACI J., 73(7), 809–820.
Gardner, N. J., Keller, L., Quattrociocchi, R., and Charitou, G. (2012). “Field investigation of formwork pressures using self-consolidating concrete.” ACI Concr. Int., 34(1), 41–48.
Giammatteo, M. M., Gregori, A., and Totani, G., (2007). “In-situ measurement of formwork pressures generated by self-compacting concrete.” Comput. Methods Exp. Meas., 46, 851–860.
Hurd, M. K., (2005). “Formwork for concrete.” American Concrete Institute, Farmington Hills, MI.
Hurd, M. K. (2007). “Lateral pressures for formwork design.” ACI Concr Int., 29(6), 31–33.
Khayat, K. H., and Assaad, J. (2006). “Effect of w/cm and high-range water-reducing admixture on formwork pressure and thixotropy of self-consolidating concrete.” ACI Mater. J., 103(3), 186–193.
Khayat, K. H., and Assaad, J. (2008). “Use of thixotropy-enhancing agent to reduce formwork pressure exerted by self-consolidating concrete.” ACI Mater. J., 105(1), 88–96.
Khayat, K. H., Assaad, J., Mesbah, H., and Lessard, M. (2005). “Effect of section width and casting rate on variations of formwork pressure of self-consolidating concrete.” Mater. Struct., 38(1), 73–78.
Khayat, K. H., and Omran, A. F. (2009). “State-of-the-art review of form pressure exerted by self-consolidating concrete.” ⟨http://www.concretesdc.org/projects/SCCreport.htm⟩ (Nov. 4, 2016).
Leemann, A., and Hoffmann, C. (2003). “Pressure of self-compacting concrete on the formwork.” Int. RILEM Symp. on Self-Compacting Concrete, O. Wallevik and I. Nielsson, eds., RILEM Publications SARL, 288–295.
Leemann, A., Hoffmann, C., and Winnefeld, F. (2006). “Pressure of self-compacting concrete on formwork.” ACI Concr. Int., 28(2), 27–31.
McCarthy, M. J., Dhir, R. K., Caliskan, S., and Ashraf, M. K., (2012). “Influence of self-compacting concrete on the lateral pressure on formwork.” Proc. ICE—Struct. Build., 165(3), 127–138.
Omran, A. F., Elaguab, Y. M., and Khayat, K. H. (2014). “Effect of placement characteristics on SCC lateral pressure variations.” J. Constr. Build. Mater., 66(15), 507–514.
Omran, A. F., Khayat, K. H., and Elaguab, Y. M. (2010). “Effect of SCC mixture composition on thixotropy and formwork pressure.” J. Mater. Civ. Eng., 876–888.
Omran, A. F., Naji, S., and Khayat, K. H. (2011). “Portable vane test to assess structural build-up at rest of self-consolidating concrete.” ACI Mater J., 108(6), 628–637.
Palanca, M. J. (1982). “Presión del hormigón fresco.”, Instituto Eduardo Torroja de Ciencias de la Construcción, Madrid, Spain.
Perrot, A., Amziane, S., Ovarlez, G., and Roussel, N. (2009). “SCC formwork pressure: Influence of steel rebars.” Cem Concr Res., 39(6), 524–528.
Proske, T., and Graubner, C. (2002). “Self-compacting concrete—Pressure on formwork and ability to deaerate.” Darmstadt Concrete, 17, 1–15.
Ritchie, A. G. B. (1962). “Pressures developed by concrete on formwork.” Civil Eng. Public Works Rev., 57(672), 885–888.
Rodin, S., (1952). “Pressure of concrete on formwork.” Proc., Inst. Civil Eng., 1(6), 709–746.
Santilli, A., Puente, I., and Tanco, M., (2011). “A factorial design study to determine the significant parameters of fresh concrete lateral pressure and initial rate of pressure decay.” Const. and Build. Mater., 25(4), 1946–1955.
Tejeda-Dominguez, F., and Lange, D. A. (2005). “Effect of formwork material on laboratory measurements of SCC formwork pressure.” Proc., 2nd North American Conf. on Design and Use of Self-Consolidating Concrete (SCC 2005) and 4th Int. RILEM Symp. on Self-Compacting Concrete, Shah, S. P., ed., Evanston, IL, 525–532.
Tejeda-Dominguez, F., Lange, D. A., and D’Ambrosia, M. D. (2006). “Formwork pressure of self-consolidating concrete in tall wall field applications.” J. Transp. Res. Board, 1–7.
Vanhove, Y., Djelal, C., and Magnin, A. (2000). “Friction behaviour of a fluid concrete against a metallic surface.” Int. Conf. on Advances in Mechanical Behaviour, Plasticity and Damage, Elsevier Science, Oxford, U.K., 679–684.
Information & Authors
Information
Published In
Copyright
©2016 American Society of Civil Engineers.
History
Received: Mar 21, 2016
Accepted: Sep 20, 2016
Published online: Nov 28, 2016
Discussion open until: Apr 28, 2017
Published in print: May 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.