Developing Low-Cost Activators for Alkali-Activated Phosphorus Slag-Based Binders
Publication: Journal of Materials in Civil Engineering
Volume 29, Issue 6
Abstract
Making use of low-cost alkali activators to produce suitable binders can play a key role in replacing portland cement by alkali-activated binders. The most effective and common activators are often based on sodium hydroxide and/or sodium silicate, which are relatively high in cost. In this study, attempts were made to develop suitable activators incorporating low-cost alkali and alkali earth metal-bearing salts for phosphorus slag. To fulfill this purpose, plain NaOH as a control activator as well as combinations of the control activator with and also a combination of and at different proportions were used to activate ground phosphorus slag. To evaluate the cementing property and soundness of the resulting mixes, compressive strength and efflorescence severity data were employed, respectively. Two suitable cement mixes were then selected and their chemical bond structure and the rate of adiabatic heat release were characterized by means of Fourier transform infrared spectroscopy (FTIR) and adiabatic calorimetry data, respectively. Finally, cost assessment done on the corresponding low-cost activators of the selected cement mixes revealed significantly lower cost-to-compressive strength ratios compared to the conventional control activators.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abdollahnejad, Z., Pacheco-Torgal, F., Félix, T., Tahri, W., and Barroso Aguiar, J. (2015). “Mix design, properties and cost analysis of fly ash-based geopolymer foam.” Constr. Build. Mater., 80(1), 18–30.
Allahverdi, A., and Kani, E. N. (2013). “Use of construction and demolition waste (CDW) for alkali-activated or geopolymer cements.” Handbook of recycled concrete and demolition waste, F. Pacheco-Torgal, V. W. Y. Tam, J. A. Labrincha, Y. Ding, and J. de Brito, eds., Woodhead Publishing, Cambridge, U.K., 439–475.
Alonso, S., and Palomo, A. (2001). “Alkaline activation of metakaolin and calcium hydroxide mixtures: Influence of temperature, activator concentration and solids ratio.” Mater. Lett., 47(1–2), 55–62.
ASTM. (2013a). “Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens).” ASTM C109/C109M-13, West Conshohocken, PA.
ASTM. (2013b). “Standard test methods for sampling and testing fly ash or natural pozzolans for use in portland-cement concrete.” ASTM C311/C311M-13, West Conshohocken, PA.
ASTM. (2014). “Standard specification for flow table for use in tests of hydraulic cement.” ASTM C230/C230M-14, West Conshohocken, PA.
ASTM. (2015a). “Standard test method for heat of hydration of hydraulic cement.” ASTM C186-15a, West Conshohocken, PA.
ASTM. (2015b). “Standard test methods for chemical analysis of hydraulic cement.” ASTM C114-15, West Conshohocken, PA.
Atiş, C. D., Bilim, C., Çelik, Ö., and Karahan, O. (2009). “Influence of activator on the strength and drying shrinkage of alkali-activated slag mortar.” Constr. Build. Mater., 23(1), 548–555.
Bakharev, T., Sanjayan, J. G., and Cheng, Y. B. (2000). “Effect of admixtures on properties of alkali-activated slag concrete.” Cem. Concr. Res., 30(9), 1367–1374.
Chen, W., and Brouwers, H. J. H. (2007). “The hydration of slag. Part 1: Reaction models for alkali-activated slag.” JMatS, 42(2), 428–443.
Clayden, N. J., Esposito, S., Aronne, A., and Pernice, P. (1999). “Solid state 27Al NMR and FTIR study of lanthanum aluminosilicate glasses.” J. Non-Cryst. Solids, 258(1–3), 11–19.
Collins, F., and Sanjayan, J. G. (2000). “Cracking tendency of alkali-activated slag concrete subjected to restrained shrinkage.” Cem. Concr. Res., 30(5), 791–798.
Duxson, P., Fernández-Jiménez, A., Provis, J. L., Lukey, G. C., Palomo, A., and Deventer, J. S. J. (2007). “Geopolymer technology: The current state of the art.” JMatS, 42(9), 2917–2933.
Ebbing, D. D. (1990). General chemistry, Houghton Mifflin Company, Boston.
GCIP (General Chemical Industrial Products). (2003). Soda ash, Parsippany, NJ.
Haha, M. B., Saout, G. L., Winnefeld, F., and Lothenbach, B. (2011). “Influence of activator type on hydration kinetics, hydrate assemblage and microstructural development of alkali activated blast-furnace slags.” Cem. Concr. Res., 41(3), 301–310.
Hindman, J. C. (1943). Properties of the system in sea water and sodium chloride solutions, Univ. of California, Los Angeles.
IME. (2015). “Iran mercantile exchange.” ⟨http://www.ime.co.ir/ime/en/page/Spot%20Market-IPOs.html⟩ (Nov. 23, 2016).
Khale, D., and Chaudhary, R. (2007). “Mechanism of geopolymerization and factors influencing its development: A review.” JMatS, 42(3), 729–746.
Kim, M. S., Jun, Y., Lee, C., and Oh, J. E. (2013). “Use of CaO as an activator for producing a price-competitive non-cement structural binder using ground granulated blast furnace slag.” Cem. Concr. Res., 54, 208–214.
Krivenko, P. V. (1994). “Alkaline cements.” Proc., Alkaline Cements and Concretes, VIPOL Stock Company, Kiev, Ukraine, 11–129.
Lecomte, I., Henrista, C., Liégeoisa, M., Maserib, F., Rulmonta, A., and Clootsa, R. (2006). “(Micro)-structural comparison between geopolymers, alkali-activated slag cement and portland cement.” J. Eur. Ceram. Soc., 26(16), 3789–3797.
Lee, T. C., and Li, Z. S. (2010). “Conditioned MSWI ash-slag-mix as a replacement for cement in cement mortar.” Constr. Build. Mater., 24(6), 970–979.
Li, D., Shen, J., Mao, L., and Wu, X. (2000). “The influence of admixtures on the properties of phosphorous slag cement.” Cem. Concr. Res., 30(7), 1169–1173.
Li, J., Yu, Q., and Wei, J. (2011). “Structural characteristics and hydration kinetics of modified steel slag.” Cem. Concr. Res., 41(3), 324–329.
Maghsoodloorad, H., and Allahverdi, A. (2015). “Alkali-activation kinetics of phosphorus slag cement using compressive strength data.” Ceram. Silik., 59(3), 250–260.
Maghsoodloorad, H., and Allahverdi, A. (2016). “Efflorescence formation and control in alkali-activated phosphorus slag cement.” Int. J. Civ. Eng., 14(6), 425–438.
Maghsoodloorad, H., Khaliliamiri, H., Allahverdi, A., Lachemi, M., and Hossain, K. M. A. (2014). “Recycling phosphorus slag as a precursor for alkali-activated binder: Impact of type and dosage of activator.” Ceram. Silik., 58(3), 227–236.
Najafikani, E., Allahverdi, A., and Provis, J. L. (2012). “Efflorescence control in geopolymer binders based on natural pozzolan.” Cem. Concr. Compos., 34(1), 25–33.
Oh, J. E., Monteiro, P. J. M., Jun, S. S., Choi, S., and Clark, S. M. (2010). “The evolution of strength and crystalline phases for alkali-activated ground blast furnace slag and fly ash-based geopolymers.” Cem. Concr. Res., 40(2), 189–196.
Ouellet-Plamondon, C., and Habert, G. (2014). “Life cycle analysis (LCA) of alkali-activated cements and concretes.” Handbook of alkali-activated cements, mortars and concretes, F. Pacheco-Torgal, J. Labrincha, A. Palomo, C. Leonelli, and P. Chindaprasirt, eds., WoodHead Publishing, Cambridge, U.K., 663–686.
Pallagi, A., et al. (2012). “The solubility of in extremely concentrated NaOH solutions at 25°C.” Cent. Eur. J. Chem., 10(2), 332–337.
Palomo, A., Grutzek, M. W., and Blanco, M. T. (1999). “Alkali-activated fly ashes: A cement for the future.” Cem. Concr. Res., 29(8), 1323–1329.
Puertas, F., Palacios, M., Manzano, H., Dolado, J. S., Rico, A., and Rodríguez, J. (2011). “A model for the C─A─S─H gel formed in alkali-activated slag cements.” J. Eur. Ceram. Soc., 31(12), 2043–2056.
RILEM. (1997). “Recommendations of TC 119-TCE: Avoidance of thermal cracking in concrete at early ages.” Mater. Struct., 30(202), 451–464.
Sakulich, A. R., Anderson, E., Schauer, C., and Barsoum, M. W. (2009). “Mechanical and microstructural characterization of an alkali-activated slag/limestone fine aggregate concrete.” Constr. Build. Mater., 23(8), 2951–2957.
Sakulich, A. R., Anderson, E., Schauer, C. L., and Barsoum, M. W. (2010a). “Influence of Si:Al ratio on the microstructural and mechanical properties of a fine-limestone aggregate alkali-activated slag concrete.” Mater. Struct., 43(7), 1025–1035.
Sakulich, A. R., Miller, S., and Barsoum, M. W. (2010b). “Chemical and microstructural characterization of 20-month-old alkali-activated slag cements.” J. Am. Ceram. Soc., 93(6), 1741–1748.
Shi, C., Jiménez, A. F., and Palomo, A. (2011). “New cements for the 21st century: The pursuit of an alternative to portland cement.” Cem. Concr. Res., 41(7), 750–763.
Shi, C., Krivenko, P. V., and Roy, D. M. (2006). Alkali-activated cements and concretes, Taylor & Francis, New York.
Shi, C., and Li, Y. (1989). “Investigation on some factors affecting the characteristics of alkali-phosphorus slag cement.” Cem. Concr. Res., 19(4), 527–533.
Shi, C., Wu, X., and Tang, M. (1991). “Hydration of alkali-slag cements at 150°C.” Cem. Concr. Res., 21(1), 91–100.
Simlote, P. K. (1992). “Kinetics of limestone dissolution: Effect of limestone composition and temperature.” M.S. thesis, Syracuse Univ., Syracuse, NY.
Škvára, F., Kopecký, L., Myšková, L., Šmilauer, V., Alberovská, L., and Vinšová, L. (2009a). “Aluminosilicate polymers-influence of elevated temperatures, efflorescence.” Ceram. Silik., 53(4), 276–282.
Škvára, F., Kopecký, L., Šmilauer, V., and Bittnarb, Z. (2009b). “Material and structural characterization of alkali activated low-calcium brown coal fly ash.” J. Hazard. Mater., 168(2–3), 711–720.
Škvára, F., Šmilauer, V., Hlaváček, P., Kopecký, L., and Cílová, Z. (2012). “A weak alkali bond in (N, K)-A-S-H Gels: Evidence from leaching and modeling.” Ceram. Silik., 56(4), 374–382.
Somna, K., Jaturapitakkul, C., Kajitvichyanukul, P., and Chindaprasirt, P. (2011). “NaOH-activated ground fly ash geopolymer cured at ambient temperature.” Fuel, 90(6), 2118–2124.
Song, S., and Jennings, H. M. (1999). “Pore solution chemistry of alkali-activated ground granulated blast-furnace slag.” Cem. Concr. Res., 29(2), 159–170.
Taher, M. A. (2007). “Influence of thermally treated phosphogypsum on the properties of portland slag cement.” Conserv. Recycl., 52(1), 28–38.
Talling, B., and Brandstetr, J. (1989). “Present state and future of alkali-activated slag concretes.” 3rd Int. Conf. on Fly-ash, Silica Fume, Slag and Natural Pozzalans, Concrete, American Concrete Institute, Farmington Hills, MI, 1519–1546.
Thomas, R. J., Hailong, Y., Radlinska, A., and Peethamparan, S. (2016). “Alkali-activated slag cement concrete.” Concr. Int., 38(1), 33–38.
Torgal, F. P., Castro-Gomes, J., and Jalali, S. (2008a). “Alkali-activated binders: A review. Part 1: Historical background, terminology, reaction mechanisms and hydration products.” Constr. Build. Mater., 22(7), 1305–1314.
Torgal, F. P., Castro-Gomes, J. O., and Jalali, S. (2008b). “Alkali-activated binders: A review. Part 2: About materials and binders manufacture.” Constr. Build. Mater., 22(7), 1315–1322.
Vaughan, K. B. (1998). A quantitative analysis of interstitial fluid chemistry and limestone dissolution rates within the clastic sediment of a Karst aquifer conduit, Mammoth cave, Kentucky, Western Kentucky Univ., Bowling Green, KY.
Wang, K., Shah, S. P., and Mishulovich, A. (2004). “Effects of curing temperature and NaOH addition on hydration and strength development of clinker-free CKD-fly ash binders.” Cem. Concr. Res., 34(2), 299–309.
Wolhuter, C. W., Turkstra, J., and Morris, R. M. (1980). “Influence du chlorure de calcium sur la contraction volumique, la teneur en eau non-évaporable et la teneur en chlorure fixe du ciment portland et du laitier de haut fourneau hydrates [Effect of calcium chloride on the volume contraction, non-evaporable water content and bound chloride content of hydrated portland cement and blast-furnace slag].” Cem. Concr. Res., 10(4), 535–543.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 29 • Issue 6 • June 2017
Copyright
©2017 American Society of Civil Engineers.
History
Received: Feb 3, 2016
Accepted: Sep 1, 2016
Published online: Jan 24, 2017
Published in print: Jun 1, 2017
Discussion open until: Jun 24, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.