Corrosion Degree Effect on Nominal and Effective Strengths of Naturally Corroded Reinforcement
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 10
Abstract
This paper presents the corrosion degree effect on yield and ultimate strengths (nominal and effective) of protruding reinforcing steel that remained buried for 60 years; thus, the natural corrosion process during this period was analyzed. Tensile tests were performed on specimens taken from this protruding reinforcing steel. A characterization of the local soil where the reinforcement remained buried as an aggressive medium was performed, and micrographs were obtained in order to observe the presence of pits. The results were in agreement with studies of accelerated corrosion in a laboratory. As the corrosion degree increases, the greater is the difference between the nominal and effective strengths. Specimens with a corrosion degree of about 25% had an effective strength similar to specimens with lower corrosion degrees. Thus, care must be taken in interpreting the effective strengths for predicting the capabilities of structural elements degraded by corrosion.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors thank the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES), the Technological Institute of Aeronautics (ITA) for providing the necessary infrastructure, and Professor Ph.D. Marcelo De Julio in memoriam.
References
Almusallan, A. A. (2001). “Effect of degree of corrosion on the properties of reinforcing.” Constr. Build. Mater., 15(8), 361–368.
Apostolopoulos, C. A. (2009). “The influence of corrosion and cross section diameter on the mechanical properties of B500c steel.” J. Mater. Eng. Perform., 18(2), 190–195.
Apostolopoulos, C. A., Demis, S., and Papadakis, V. G. (2013). “Chloride-induced corrosion of steel reinforcement—Mechanical performance and pit depth analysis.” Constr. Build. Mater., 38, 139–146.
Apostolopoulos, C. A., Michalopoulos, D., and Koutsoukos, P. (2008). “The corrosion effects on the structural integrity of reinforcing steel.” J. Mater. Eng. Perform., 17(4), 506–516.
Apostolopoulos, C. A., and Papadakis, V. G. (2008). “Consequences of steel corrosion on the ductility properties of reinforcement bar.” Constr. Build. Mater., 22(12), 2316–2324.
Apostolopoulos, C. A., Papadopoulos, M. P., and Pantelakis, S. P. G. (2006). “Tensile behavior of corroded reinforcing steel bars BSt 500s.” Constr. Build. Mater., 20(9), 782–789.
ASTM. (2003). “Standard practice for preparing, cleaning, and evaluating corrosion test specimens.” ASTM G1, West Conshohocken, PA.
Balestra, C. E. T. (2013). “Corrosion degree influence on tensile strength of reinforcement—Case study of the ancient ITA Zero Wing foundations.” M.S. dissertation, Technological Institute of Aeronautics–ITA, São Jose dos Campos, Brazil (in Portuguese).
CEMCO. (2001). “Concrete durability and assessment of corroded structures.” Institute of Construction Science Eduardo Torroja, Madrid, Spain (in Spanish).
CEPAGRI. (2015). “Köppen climate classification for São Paulo state.” 〈http://www.cpa.unicamp.br/outras-informacoes/clima-dos-municipios-paulistas.html〉 (Nov. 17, 2015).
DIN. (1984). “Reinforcing steel (Betonsthal).” DIN 488-3, German Institute for Standardization, Ausgabe, Germany.
EB-3. (1939). “Common steel bars for concrete reinforced.” EB-3/39, Brazilian Association of Technical Standards, Rio de Janeiro, Brazil.
François, R., Khan, I., and Dang, V. H. (2013). “Impact of corrosion on mechanical properties of steel embedded in 27-year-old corroded reinforced concrete beams.” Mater. Struct., 46(6), 889–910.
Han, S. J., Lee, D. H., Kim, K. S., Seo, S. Y., and Moon, J. (2013). “Degradation of flexural strength in reinforced concrete members caused by steel corrosion.” Constr. Build. Mater., 54, 572–583.
Ji, J., Zhang, C., Kodikara, J., and Yang, S. Q. (2015). “Prediction of stress concentration factor of corrosion pits on buried pipes by least squares support vector machine.” Eng. Fail. Anal., 55, 131–138.
Jin, L., and Zhang, R. (2015). “Investigation on the cracking behavior of concrete cover induced by corner located rebar corrosion.” Eng. Fail. Anal., 52, 129–143.
Khan, I., François, R., and Castel, A. (2014). “Prediction of reinforcement corrosion using corrosion induced cracks width in corroded reinforced concrete beams.” Constr. Build. Mater., 56, 84–96.
Medeiros-Junior, R. A., Lima, M. G., Brito, P. C., and Medeiros, M. H. F. (2015a). “Chloride penetration into concrete in an offshore platform-analysis of exposure conditions.” Ocean Eng., 103, 78–87.
Medeiros-Junior, R. A., Lima, M. G., and Medeiros, M. H. F. (2015b). “Service life of concrete structures considering the effects of temperature and relative humidity on chloride transport.” Environ. Dev. Sustainability, 17(5), 1103–1119.
NACE International Institute. (2014). “Soil corrosion.” 〈http://www.nace.org/StarterApps/Wiki/Wiki.aspx?wiki=141〉 (May 17, 2014).
NBR. (2002). “Metallic materials—Tensile test at room temperature.” NBR 6892/02, Brazilian Association of Technical Standards, Rio de Janeiro, Brazil.
NBR. (2007). “Steel for reinforcing the reinforced concrete structures.” NBR 7480/07, Brazilian Association of Technical Standards, Rio de Janeiro, Brazil.
NBR. (2014). “Concrete structures design—Procedure.” NBR 6118/14, Brazilian Association of Technical Standards, Rio de Janeiro, Brazil.
Palssom, R., and Mirza, M. S. (2002). “Mechanical response of corroded steel reinforcement of abandoned concrete bridge.” ACI Struct. J., 99(2), 157–162.
Papadopoulos, M. P., Apostolopoulos, C. A., Zervaki, A. D., and Haidemenopoulos, G. N. (2011). “Corrosion of exposed rebars associated mechanical degradation and correlation with accelerated corrosion test.” Constr. Build. Mater., 25(8), 3367–3374.
Pape, T. M., and Melchers, R. E. (2012). “Performance of 45-year-old corroded prestressed concrete beams.” Struct. Build., 166(10), 547–559.
Rehman, S., and Al-Hadhrami, L. M. (2013). “Web-based national corrosion cost inventory system for Saudi Arabia.” Anti-Corros. Methods Mater., 61(2), 77–92.
RILEM TC 178-TCM. (2002). “Analysis of total chloride content in concrete.” Mater. Struct., 35, 583–585.
Shekhter, A., Crawford, B. R., Loader, C., and Hu, W. (2015). “The effect of pitting corrosion on the safe-life prediction of the Royal Australian Air Force P-3C Orion aircraft.” Eng. Fail. Anal., 55, 193–207.
Silva, A. R. (2010). “Protruding reinforcing steel corrosion buried for 60 years—Case study of ITA Zero Wing foundations.” M.S. dissertation, Technological Institute of Aeronautics–ITA, São Jose dos Campos, Brazil (in Portuguese).
Uller, L., and Trocónis, O. (1997). “Manual of inspection, assessment and diagnosis of corroded reinforced concrete structures.” Instituto de Ciencias de la Construcción Eduardo Torroja, Rio de Janeiro, Brazil (in Spanish).
Zhang, W., Song, X., Gu, X., and Li, S. (2012). “Tensile and fatigue behavior of corroded rebars.” Constr. Build. Mater., 34, 409–417.
Zhang, W. P., Dai, H. C., Gu, X. L., and Wu, S. N. (2010). “Effects of corrosion pits on mechanical properties of corroded steel bars.” Earth and space 2010: Engineering, science, construction, and operations in challenging environments, G. Song and R. B. Malla, eds., ASCE, Reston, VA, 3504–3511.
Zhu, W., and François, R. (2014). “Experimental investigation of the relationship between residual cross section shapes and the ductility of corroded bars.” Constr. Build. Mater., 69, 335–345.
Zhu, W., François, R., Coronelli, D., and Cleland, D. (2013). “Effect of corrosion of reinforcement on the mechanical behaviour of highly corroded RC beams.” Constr. Build. Mater., 56, 544–554.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Oct 2, 2015
Accepted: Jan 20, 2016
Published online: May 5, 2016
Published in print: Oct 1, 2016
Discussion open until: Oct 5, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.