Relationship between Slipperiness and Other Characteristics of Stones used as Flooring Slabs
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 8
Abstract
Slip resistance is an essential parameter when dimension stones are used as inner and outer floorings. Declaration of performances of stones and their surface finishes (sawn, honed, polished, hammered, flamed, sandblasted, or brushed) in relation to conditions (wet or dry) in Conformité Européenne (CE) marking is essential for pedestrian safety. In this study, 130 samples taken from 81 stone types belonging to 13 types of petrographic families were tested according to the EN 14231 Standard, taking different finishes into consideration, during a ten-year period in the Marble Laboratory of Politecnico di Torino (Italy). A high number of pendulum friction tests (1,560) were conducted on 780 samples, and more than 7,000 readings were taken. On the basis of the obtained results, significant relations were found between the tested petrographic families and the types of finishes. A high correlation between open porosity, quartz content, and slipperiness of the stones with honed surface finishes was found. Moreover, the importance of the petrographic characterization of the stone, in relation to the declared surface finish, emerged as each petrographic family responded differently (according to its composition) to the action of the finishing abrasive.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to thank the Editor and the Reviewers for their valuable contributions and the time they spent improving the manuscript.
References
ANSI/NFSI (Accredited Standard Developer/National Floor Safety Institute). (2012). “Test method for measuring wet DCoF of common hard-surface floor materials (including action and limit thresholds for the suitable assessment of the measured values).”, Southlake.
AS/NZS (Australian and New Zealand Standard). (1993). “Slip resistance of pedestrian surfaces.”, Sidney, Australia and Wellington, New Zealand.
AS/NZS (Australian and New Zealand Standard). (2013). “Slip resistance classification of new pedestrian surface materials.”, Sidney, Australia and Wellington, New Zealand.
ASTM. (2013). “Standard test method for measuring surface frictional properties using the british pendulum tester.” ASTM E303, West Conshohocken, PA.
BSI (British Standard). (2013a). “Method of calibration—Specifications.”, London.
BSI (British Standard). (2013b). “Pendulum testers—Specifications.”, London.
Carpenter, J., Lazarus, D., and Perkins, C. (2006). “Safer surface to walking on—Reducing the risk of slipping.”, London.
CEN (European Committee for Standardization). (2003). “Natural stone test methods—Determination of the slip resistance by means of the pendulum tester.”, Brussels.
CEN (European Committee for Standardization). (2012a). “Determination of slip resistance of pedestrian surfaces—Methods of evaluation.”, Brussels.
CEN (European Committee for Standardization). (2012b). “Setts of natural stone for external paving—Requirements and test methods.”, Brussels.
CEN (European Committee for Standardization). (2012c). “Slabs of natural stone for external paving—Requirements and test methods.”, Brussels.
DIN (German Institute for Standardization). (1992). “Testing of floor coverings—Determination of the anti-slip properties—Wet-loaded barefoot areas—Walking method—Ramp test.”, Berlin.
DIN (German Institute for Standardization). (2004). “Testing of floor coverings—Determination of the anti-slip property—Workrooms and fields of activities with slip danger, walking method—Ramp test.”, Berlin.
Englander, F., Hodson, T. J., and Terregrossa, R. A. (1996). “Economic dimensions of slip and fall injuries.” J. Forensic. Sci., 41(5), 733–746.
Garcia del Cura, M. A., Benavente, D., Bernabéu, A., and Martinez Martinez, J. (2008). “The effects of surface finishes on outdoor granite and limestone pavers.” Materiales de Costrucción, 58(289–290), 65–79.
Gronqvist, R., Hirvonen, M., and Tohv, A. (2000). “Evaluation of three portable floor slipperiness testers.” Int. J. Ind. Ergon., 25(1), 85–95.
HSE (Health and Safety Executive). (2015). “Slips and trips—Hazard spotting checklist.” 〈http://www.hse.gov.uk/slips/flooring.htm〉 (Apr. 21, 2015).
Hunter, R. B. (1929). “Method of measuring frictional coefficient of walkway materials.” Bureau Stand. J. Res., 5(2), 329–347.
Kanafi, M. M., Kuosmanen, A., Pellinen, T. K., and Tuononen, A. J. (2014). “Macro- and micro-texture evolution of road pavements and correlation with friction.” Int. J. Pavement Eng., 16(2), 168–179.
Karaca, Z. (2012). “Relationship between the mechanical properties and the surface roughness of marble.” Int. J. Mater. Res., 103(5), 633–637.
Karaca, Z., Gürcan, S., Gökçe, M. V., and Sivrikaya, O. (2013). “Assessment of the results of the pendulum friction tester (EN 14231) for natural building stones used as floor-coverings.” Constr. Build. Mater., 47, 1182–1187.
Karaca, Z., Öztank, N., Gökçe, M. V., and Elçi, H. (2011). “Effects of surface-finishing forms and cement-filling on porous dimension limestone deterioration in cold regions.” Cold Reg. Sci. Technol., 68(3), 124–129.
Li, K. W., and Horng, J. H. (2009). “A comparison of friction measurements results using two slipmeters.” Proc., Conf. on Industrial Engineering and Engineering Management, IEEE, Hong Kong, 2159–2163.
Loo-Morrey, M. (2006). “Ramp testing natural and man made stone floors.”, Grown, Buxton, U.K.
Marradi, A., Secchiari, L., and Lezzerini, M. (2008). “The qualification of stone materials for their application in road stone pavements.” 2nd Int. Congress Dimension Stone, Internazionale Marmi e Macchine, Carrara, Italy, 225–235.
Ministerial Decree. (1989). “Prescrizioni tecniche necessarie a garantire l’accessibilità, l’adattabilità e la visitabilità degli edifici privati e di edilizia residenziale pubblica sovvenzionata e agevolata, ai fini del superamento e dell’eliminazione delle barriere architettoniche [Technical requirements necessary to ensure accessibility, adaptability and visitability of private buildings and public housing subsidized and facilitated, for the purpose of overcoming and removal of architectural barriers].”, BRCA, Rome (in Italian).
Redfern, M. S., and Bidanda, B. (1994). “Slip resistance of the shoe-floor interface under biomechanically-relevant conditions.” Ergonomics, 37(3), 511–524.
Ricotti, R., Delucchi, M., and Cerisola, G. (2009). “A comparison of results from portable and laboratory floor slipperiness testers.” J. Ergon., 39(2), 353–357.
Standards Australia Handbook. (1999). “An introductory guide to the slip resistance of pedestrian surface materials.”, Sydney, NSW, Australia.
Tassone, R., and Signori, G. (2008). “Evaluation of slipperiness on wet surfaces: A study comparing the response of ramp and pendulum test methods.” 2nd Int. Congress Dimension Stone, Internazionale Marmi e Macchine, Carrara, Italy, 251–255.
Yates, T. J. S., and Richardson, D. (2000). “Flooring, paving and sets: Requirements for safety in use.”, British Research Establishment, Garston, U.K.
Zhang, L., Ong, G. P., and Fwa, T. F. (2013). “A numerical study on the influence of aggregate size on skid resistance performance of porous pavements.” Asian Transp. Stud., 3(3), 284–297.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 28 • Issue 8 • August 2016
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Dec 10, 2014
Accepted: Nov 25, 2015
Published online: Feb 23, 2016
Discussion open until: Jul 23, 2016
Published in print: Aug 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.