Stabilization of Demolition Materials for Pavement Base/Subbase Applications Using Fly Ash and Slag Geopolymers: Laboratory Investigation
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 7
Abstract
The use of recycled construction and demolition (C&D) materials in unbound and cement stabilized pavement base/subbase applications has generated growing interest in recent years. C&D materials consisting of crushed brick (CB), recycled crushed aggregate (RCA), and reclaimed asphalt pavement (RAP) have been investigated in unbound and cement stabilized pavement base/subbase applications. However, the high carbon footprint of using cement for pavement base/subbase stabilization has led to this research to seek alternative low-carbon binders. This study evaluates the behavior of C&D materials when stabilized with geopolymers. Fly ash (FA) and ground granulated blast furnace slag (S) were used as pozzolanic binders and a different alkaline activator solution to pozzolanic binder ratio was tested. A maximum of 4% of dry weight of soil was used for geopolymer stabilization of the C&D materials. The binders used were either 4% FA, 2% FA+ 2% S, or 4% S. The geotechnical engineering and strength properties of these geopolymer-stabilized C&D materials were evaluated to ascertain their performance for pavement base/subbase applications. Elastic modulus, compressive strength, and resilient modulus of the blends were tested and analyzed in this research. Both the resilient modulus of the C&D materials and compressive strength were found to increase as a result of geopolymer stabilization. Geopolymer stabilization was found to be most effective for RCA. Higher compressive strength will be achieved by slag-based geopolymer stabilization when compared with fly ash–based geopolymer stabilization. The effect of alkaline activator to pozzolanic binder ratio on the enhancement of geotechnical properties of C&D materials was also analyzed. The performance of the geopolymer-stabilized C&D materials was furthermore compared with that of traditional cement-stabilized C&D materials. Geopolymer-stabilized RCA and RAP were found to be a viable and sustainable option for the stabilization of future pavement bases/subbases.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported under the Australian Research Council’s Linkage Projects funding scheme (Project No. LP120100107).
References
AASHTO. (1994). “Standard test method of tests for resilient modulus of subgrade soils and untreated base/subbase materials.” AASHTO T 294-94, Washington, DC.
AASHTO. (2007). “Standard method of test for determining the resilient modulus of soils and aggregate materials.” AASHTO T307-99, Washington, DC.
Arulrajah, A., Disfani, M. M., Haghighi, H., Mohammadinia, A., and Horpibulsuk, S. (2015). “Modulus of rupture evaluation of cement stabilized recycled glass/recycled concrete aggregate blends.” Constr. Build. Mater., 84, 146–155.
Arulrajah, A., Disfani, M. M., Horpibulsuk, S., Suksiripattanapong, C., and Prongmanee, N. (2014). “Physical properties and shear strength responses of recycled construction and demolition materials in unbound pavement base/subbase applications.” Constr. Build. Mater., 58, 245–257.
Arulrajah, A., Piratheepan, J., Disfani, M. M., and Bo, M. W. (2013). “Geotechnical and geoenvironmental properties of recycled construction and demolition materials in pavement subbase applications.” J. Mater. Civ. Eng., 1077–1088.
ASTM. (2006). “Standard test method for resistance to degradation of small-size coarse aggregate by abrasion and impact in the Los Angeles machine.” ASTM C131, West Conshohocken, PA.
ASTM. (2007a). “Standard test method for particle-size analysis of soils.” ASTM D422-63, West Conshohocken, PA.
ASTM. (2007b). “Standard test methods for compressive strength of molded soil-cement cylinders.” ASTM D1633, West Conshohocken, PA.
ASTM. (2007c). “Standard test methods for moisture, ash, and organic matter of peat and other organic soils.” ASTM D2974-07a, West Conshohocken, PA.
ASTM. (2009). “Standard test method for unconfined compressive strength of compacted soil-lime mixtures.” ASTM D5102, West Conshohocken, PA.
ASTM. (2011). “Standard practice for classification of soils for engineering purposes (unified soil classification system).” ASTM D2487-11, West Conshohocken, PA.
ASTM. (2012). “Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete.” ASTM C618–2012, West Conshohocken, PA.
British Standard Institution. (2000). “Method for determination of particle shape: Flakiness index.” BS 812-105.1, London.
Cetin, B., Aydilek, A. H., and Li, L. (2012). “Experimental and numerical analysis of metal leaching from fly ash-amended highway bases.” Waste Manage., 32(5), 965–978.
Ceylan, H., Gopalakrishnan, K., and Kim, S. (2010). “Soil stabilization with bioenergy coproduct.” Transportation Research Record, 2186, 130–137.
Cosentino, P. J., et al. (2012). “Improving the properties of reclaimed asphalt pavement for roadway base applications.” Final Rep., Florida Dept. of Transportation, Tallahassee, FL.
Criado, M., Palomo, A., and Fernández-Jiménez, A. (2005). “Alkali activation of fly ashes. Part 1: Effect of curing conditions on the carbonation of the reaction products.” Fuel, 84(16), 2048–2054.
Crispim, F. A., et al. (2011). “The influence of laboratory compaction methods on soil structure: Mechanical and micromorphological analyses.” Soils Rocks, 34(1), 91–98.
Disfani, M. M., Arulrajah, A., Bo, M. W., and Sivakugan, N. (2012). “Environmental risks of using recycled crushed glass in road applications.” J. Cleaner Prod., 20(1), 170–179.
Disfani, M. M., Arulrajah, A., Haghighi, H., Mohammadinia, A., and Horpibulsuk, S. (2014). “Flexural beam fatigue strength evaluation of crushed brick as a supplementary material in cement stabilized recycled concrete aggregates.” Constr. Build. Mater., 68, 667–676.
Du, Y., Li, S., and Hayashi, S. (1999). “Swelling-shrinkage properties and soil improvement of compacted expansive soil, Ning-Liang Highway, China.” Eng. Geol., 53(3), 351–358.
Du, Y.-J., Jiang, N.-J., Liu, S.-Y., Jin, F., Singh, D. N., and Puppala, A. J. (2013a). “Engineering properties and microstructural characteristics of cement-stabilized zinc-contaminated kaolin.” Can. Geotech. J., 51(3), 289–302.
Du, Y.-J., Wei, M. L., Jin, F., and Liu, Z. B. (2013b). “Stress-strain relation and strength characteristics of cement treated zinc-contaminated clay.” Eng. Geol., 167, 20–26.
Fernández-Jiménez, A., and Palomo, A. (2005). “Composition and microstructure of alkali activated fly ash binder: Effect of the activator.” Cem. Concr. Res., 35(10), 1984–1992.
Hewlett, P. (2003). Lea’s chemistry of cement and concrete, Elsevier, Oxford, U.K.
Horpibulsuk, S., Phetchuay, C., Chinkulkijniwat, A., and Cholaphatsorn, A. (2013). “Strength development in silty clay stabilized with calcium carbide residue and fly ash.” Soils Found., 53(4), 477–486.
Hoyos, L. R., Puppala, A. J., and Ordonez, C. A. (2011). “Characterization of cement fiber-treated reclaimed asphalt pavement aggregates: Preliminary investigation.” J. Mater. Civ. Eng., 977–989.
Kong, D. L., and Sanjayan, J. G. (2010). “Effect of elevated temperatures on geopolymer paste, mortar and concrete.” Cem. Concr. Res., 40(2), 334–339.
Li, L., Benson, C. H., Edil, T. B., and Hatipoglu, B. (2008). “Sustainable construction case history: Fly ash stabilization of recycled asphalt pavement material.” Geotech. Geol. Eng., 26(2), 177–187.
Li, L., Edil, T., and Benson, C. (2009). “Mechanical performance of pavement geomaterials stabilized with fly ash in field applications.” Jackson State Univ., Jackson, MS.
Mohammadinia, A., Arulrajah, A., Sanjayan, J., Disfani, M., Bo, M., and Darmawan, S. (2014). “Laboratory evaluation of the use of cement-treated construction and demolition materials in pavement base and subbase applications.” J. Mater. Civ. Eng., 04014186.
Nematollahi, B., and Sanjayan, J. (2014). “Effect of different superplasticizers and activator combinations on workability and strength of fly ash based geopolymer.” Mater. Des., 57, 667–672.
Nematollahi, B., Sanjayan, J., and Shaikh, F. U. A. (2014). “Comparative deflection hardening behavior of short fiber reinforced geopolymer composites.” Constr. Build. Mater., 70, 54–64.
Phetchuay, C., Horpibulsuk, S., Suksiripattanapong, C., Chinkulkijniwat, A., Arulrajah, A., and Disfani, M. M. (2014). “Calcium carbide residue: Alkaline activator for clay-fly ash geopolymer.” Constr. Build. Mater., 69, 285–294.
Puppala, A. J., Hoyos, L. R., and Potturi, A. K. (2011). “Resilient moduli response of moderately cement-treated reclaimed asphalt pavement aggregates.” J. Mater. Civ. Eng., 990–998.
Rahman, M. A., Imteaz, M. A., Arulrajah, A., and Disfani, M. M. (2014). “Suitability of recycled construction and demolition aggregates as alternative pipe backfilling materials.” J. Cleaner Prod., 66, 75–84.
Rahman, M. A., Imteaz, M. A., Arulrajah, A., Piratheepan, J., and Disfani, M. M. (2015). “Recycled construction and demolition materials in permeable pavement systems: Geotechnical and hydraulic characteristics.” Cleaner Prod., 90, 183–194.
Senadheera, S., Nash, P., and Rana, A. (1995). Characterization of the behavior of granular road material containing glass cullet, Dept. of Civil Engineering, Texas Tech Univ., Lubbock, TX.
Snellings, R., Mertens, G., and Elsen, J. (2012). “Supplementary cementitious materials.” Rev. Mineral. Geochem., 74(1), 211–278.
Standards Australia. (1997). “Soil chemical tests—Determination of the pH value of a soil—Electrometric method.” AS 1289.4.3.1, Sydney, Australia.
Standards Australia. (2000a). “Particle density and water absorption of coarse aggregate—weighing-in-water method.” AS 1141.6.1, Sydney, Australia.
Standards Australia. (2000b). “Particle density and water absorption of fine aggregate.” AS 1141.5.1, Sydney, Australia.
Standards Australia. (2003). “Soil compaction and density tests—Determination of the dry density/moisture content relation of a soil using modified compactive effort.” AS 1289.5.2.1, Sydney, Australia.
Stewart, D. (2008). “Lignin as a base material for materials applications: Chemistry, application and economics.” Ind. Crops Prod., 27(2), 202–207.
Sukmak, P., Horpibulsuk, S., and Shen, S.-L. (2013). “Strength development in clay-fly ash geopolymer.” Constr. Build. Mater., 40, 566–574.
Sustainability Victoria. (2010). Recycling industry annual survey 2008–2009, Melbourne, Australia.
Texas Department of Transportation. (2010). Cement treatment (plant-mixed) 276, Austin, TX.
Texas Department of Transportation. (2013). “Test procedure for soil-cement testing.”, Austin, TX.
Thakur, J. K., and Han, J. (2015). “Recent development of recycled asphalt pavement (RAP) bases treated for roadway applications.” Transp. Infrastruct. Geotechnol., 2(2), 68–86.
Uzan, J. (1985). “Characterization of granular material.” Transp. Res. Rec., 1022, 52–59.
VicRoads. (2011). 812 Crushed rock for pavement base and subbase, VIC, Australia.
Wen, H., Warner, J., Edil, T., and Wang, G. (2010). “Laboratory comparison of crushed aggregate and recycled pavement material with and without high carbon fly ash.” Geotech. Geol. Eng., 28(4), 405–411.
Zhang, J., Provis, J. L., Feng, D., and van Deventer, J. S. J. (2008). “Geopolymers for immobilization of Cr6+, Cd2+, and Pb2+.” J. Hazard. Mater., 157(2–3), 587–598.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 28 • Issue 7 • July 2016
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Dec 18, 2014
Accepted: Nov 4, 2015
Published online: Feb 2, 2016
Published in print: Jul 1, 2016
Discussion open until: Jul 2, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.