Shear Behavior of SCC Beams with Different Coarse-to-Fine Aggregate Ratios and Coarse Aggregate Types
Publication: Journal of Materials in Civil Engineering
Volume 27, Issue 11
Abstract
The effect of mixture composition and coarse aggregate density on the shear strength and cracking behavior of self-consolidating concrete (SCC) beams are presented in this study. The experimental test parameters included coarse/fine () aggregate ratio (ranging from 0.7 to 1.2), coarse aggregate size (10 and 20 mm), coarse aggregate type/density (slag, expanded slate, and crushed stone), and varying compressive strengths (26–72 MPa). The density of the tested mixtures varied from 1,848 to . The study investigates the fresh properties of all tested mixtures and the shear strength and cracking behavior of 16 full-scale concrete beams. Based on some selected design codes, the ultimate shear strength of the tested beams is also predicted. The results showed that SCC mixtures with a higher ratio or bigger normal-weight aggregate had better flowability and less high range water reducer admixtures (HRWRA) demand. Although all tested beams showed comparable normalized shear strength, beams with a high ratio or bigger normal-weight aggregate had higher postdiagonal cracking resistance. The results also showed that the expanded slate and slag lightweight aggregates were found to be relatively strong (compared to most common lightweight aggregates) as they did not entirely break along the diagonal crack. Increasing the volume of these lightweight aggregates in SCC mixtures not only reduced the mixture density but also enhanced the postdiagonal cracking resistance.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (2007). “AASHTO LRFD bridge design specifications and commentary.”, Washington, DC.
ACI (American Concrete Institute). (2008). “Building code requirements for structural concrete (ACI 318-08) and commentary (ACI 318 R-08).”, Farmington Hills, MI.
ASTM. (2001). “Standard test method for compressive strength of cylindrical concrete specimens.”, West Conshohocken, PA.
ASTM. (2011). “Standard test method for slump flow of self-consolidating concrete.”, West Conshohocken, PA.
ASTM. (2012a). “Standard specification for coal fly ash and raw or calcined natural Pozzolan for use in concrete.”, West Conshohocken, PA.
ASTM. (2012b). “Standard specification for portland cement.”, West Conshohocken, PA.
ASTM. (2013). “Standard specification for chemical admixtures for concrete.”, West Conshohocken, PA.
Chia, K. S., and Zhang, M. H. (2004). “Effect of chemical admixtures on rheological parameters and stability of fresh lightweight aggregate concrete.” Mag. Concr. Res., 56(8), 465–473.
CSA (Canadian Standards Association). (2004). “Design of concrete structures.”, Committee A23.3, Rexdale, ON, Canada.
Cyr, M., and Mouret, M. (2003). “Rheological characterization of superplasticized cement pastes containing mineral admixtures: Consequences on self-compacting concrete design.”, 241–256.
Dymond, B. Z. (2007). “Shear strength of APcbt-53 girder fabricated with lightweight, self-consolidating concrete.” Master’s thesis, Virginia Tech, Blacksburg, VA.
EFNARC (European Federation for Specialist Construction Chemicals, and Concrete Systems). (2005). The European guidelines for self-compacting concrete specification, production and use, English Ed., Norfolk, U.K.
Eurocode 2. (2005). “Design of concrete structures. Part 1: General rules and rules for buildings.”, Thomas Telford, London.
Fujiwara, H., Nagataki, S., Otsuki, N., and Endo, E. (1996). “Study on reducing unit powder content of high-fluidity concrete by controlling powder particle size distribution.” Concr. Lib. Jpn. Soc. Civ. Eng., 28, 117–128.
Hassan, A. A. A., Lachemi, M., and Hossain, K. M. A. (2010). “Effect of metakaolin on the rheology of self-consolidating concrete.” Design, production and placement of self-consolidating concrete, RILEM book series 1, Springer, 103–112.
Hu, J., and Wang, K. (2011). “Effect of coarse aggregate characteristics on concrete rheology.” Constr. Build. Mater., 25(3), 1196–1204.
Hubertova, M., and Hela, R. (2007). “The effect of metakaolin and silica fume on the properties of lightweight self-consolidating concrete.”, American Concrete Institute, Detroit, 35–48.
Joseph, D. (2010). “Influence of aggregate on fracture properties of concrete.” M.S. thesis, College of Engineering, Trivandrum, India.
Justice, J. M., and Kurtis, K. E. (2007). “Influence of metakaolin surface area on properties of cement-based materials.” J. Mater. Civ. Eng., 19(9), 899–1561.
Kani, G. N. J., Huggins, M. W., and Wittkopp, R. R. (1979). Shear in reinforced concrete, Univ. of Toronto Press, Toronto, Canada, 225.
Khayat, K. H. (2000). “Optimisation and performance of air-entrained, self-consolidating concrete.” ACI Mater. J., 97(5), 526–535.
Khayat, K. H., Manai, K., and Trudel, A. (1997). “In situ mechanical properties of wall elements using self-consolidating concrete.” ACI Mater. J., 94(6), 491–500.
Khayat, K. H., Paultre, P., and Tremblay, S. (2001). “Structural performance and in-place properties of self-consolidating concrete used for casting highly reinforced columns.” ACI Mater. J., 98(5), 371–378.
Kim, Y. H., Hueste, M. B. D., Trejo, D., and Cline, D. B. H. (2010). “Shear characteristics and design for high-strength self-consolidating concrete.” J. Struct. Eng., 989–1000.
Kwasny, J., Sonebi, M., Taylor, S., Bai, Y., Owens, K., and Doherty, W. (2012). “Influence of the type of coarse lightweight aggregate on properties of semilightweight self-consolidating concrete.” J. Mater. Civ. Eng., 1474–1483.
Lachemi, M., Hossain, K. M. A., and Lambros, V. (2005). “Shear resistance of self-consolidating concrete beams—Experimental investigation.” Can. J. Civ. Eng., 32(6), 1103–1113.
Lachemi, M., Hossain, K. M. A., Lambros, V., and Bouzoubaâ, N. (2003). “Development of cost-effective self-compacting concrete incorporating fly ash, slag cement, or viscosity-modifying admixtures.” ACI Mater. J., 100(5), 419–425.
Larbi, J. (1993). “Microstructure of the interfacial zone around aggregate particles in concrete.” HERON, 38(1), 1–69.
Madandoust, R., and Mousavi, S. Y. (2012). “Fresh and hardened properties of self-compacting concrete containing metakaolin.” Constr. Build. Mater., 35, 752–760.
Mechtcherine, V., Lieboldt, M., and Butler, M. (2010). “Application of textile reinforced concrete (TRC) in prefabrication.” Proc., ACI Spring Convention, Chicago.
Neville, A. M. (1995). Properties of concrete, 4th Ed., Longman, Harlow, U.K.
NRMCA (National Ready Mixed Concrete Association). (2003). “Structural lightweight concrete.” MD.
Okamura, H. (2003). “Self-compacting concrete.” J. Adv. Concr. Technol., 1(1), 5–15.
Rao, S. V., Rao, S. M. V., Ramaseshu, D., and Kumar, R. P. (2012). “Durability performance of self compacting concrete.” Mag. Concr. Res., 64(11), 1005–1013.
Safiuddin, M., Salam, M. A., and Jumaat, M. Z. (2012). “Flowing ability of self-consolidating concrete and its binder paste phase including palm oil fuel ash.” Mag. Concr. Res., 64(10), 931–944.
Sonebi, M. (2004). “Medium strength self-compacting concrete containing fly ash: Modelling using factorial experimental plan.” Cem. Concr. Res., 34(7), 1199–1208.
Taylor, H. P. J. (1974). “The fundamental behavior of reinforced concrete beams in bending and shear.”, Detroit, 43–77.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: May 24, 2014
Accepted: Jan 14, 2015
Published online: Mar 6, 2015
Discussion open until: Aug 6, 2015
Published in print: Nov 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.