Mechanical Properties of Southern Pine Cross-Laminated Timber
Publication: Journal of Materials in Civil Engineering
Volume 27, Issue 9
Abstract
Cross-laminated timber (CLT) is a novel wood building material suitable for floor, roof, and wall assemblies in low- and mid-rise construction as an alternative to concrete and steel. CLTs are considered to provide good seismic resistance, fast erection times, carbon sequestration, and a significant reduction in greenhouse gas emissions over other construction materials. Southern pine is an abundant forest resource; yet it has not been commercially used for CLT manufacturing. The purpose of this paper was to measure the bending and shear properties of CLT material fabricated using southern pine lumber compared to product standards. Bending strength, bending stiffness, shear strength, resistance to shear by compression loading strength, and resistance to delamination were measured according to product standards, and test results were compared with values given in the standards. Bending tests were conducted on jointed beams due to test length requirements. Bending strength, bending stiffness, and wood failure in resistance to shear by compression loading tests exceeded the published values for the published values, while resistance to delamination did not meet the established criteria. The resistance to delamination results may have been affected by the uncontrolled moisture content of the lumber during fabrication of the CLTs. The application of glued laminated lumber standards to CLT products requires clarification in the orientation of loading directions for the resistance to shear by a compression loading test and the measurement of all four sides of the resistance to delamination specimens. Increased scrutiny of moisture content quality control is highly encouraged for the production of CLTs.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Funding for this project was provided by a grant from the Virginia Center for Innovative Technology. Special thanks go to David Kenealy, Director, and Travis Buchanan, former Project Manager, of the Research and Design Center for Advanced Manufacturing & Energy Efficiency (R&D CAMEE), a division of the Southern Virginia Higher Education Center (SVHEC). The authors wish to acknowledge the contributions of Dr. David DeVallance, Assistant Professor and Program Coordinator of the Wood Science and Technology Program at West Virginia University’s Division of Forestry and Natural Resources, and to his graduate students for providing access to their testing facilities and for help in the autoclave testing.
References
American Institute of Timber Construction (AITC). (2004). “Standard specifications for structural glued laminated timber of softwood species.” AITC 117, Centennial, OH.
American Institute of Timber Construction (AITC). (2005). “Standard for adhesives for use in structural glued laminated timber.” AITC 405, Centennial, OH.
American Institute of Timber Construction (AITC). (2007a). “Cyclic delamination test.” AITC T110, Centennial, OH.
American Institute of Timber Construction (AITC). (2007b). “Shear test.” AITC T107, Centennial, OH.
American National Standards Institute/American Institute of Timber Construction (ANSI/AITC). (2007). “Standard for wood products—Structural glued laminated timber.” A190.1-2007, AITC, Centennial, CO.
American National Standards Institute/APA—The Engineered Wood Association (ANSI/APA). (2012). “Standard for performance-rated cross-laminated timber.” PRG 320, APA, Tacoma, WA.
ASTM. (2013a). “Standard practice for sampling and data-analysis for structural wood and wood-based products.” D2915-10, West Conshohocken, PA.
ASTM. (2013b). “Standard test methods for direct moisture content measurement of wood and wood-base materials.” D4442-07, West Conshohocken, PA.
ASTM. (2013c). “Standard test methods for small clear specimens of timber.” D143-09, West Conshohocken, PA.
ASTM. (2013d). “Standard test methods for specific gravity of wood and wood-based materials.” D2395-07, West Conshohocken, PA.
ASTM. (2013e). “Standard test methods of static testing of lumber in structural sizes.” D198-09, West Conshohocken, PA.
AWC (American Wood Council). (2012). “National design specification for wood construction.” Washington, DC.
Ceccotti, A., and Follesa, M. (2006). “Seismic behaviour of multi-storey XLam buildings.” International Workshop on Earthquake Engineering on Timber Structures, Coimbra, Portugal, 〈http://www.timberengineering.it/Pubblicazioni/img/Articoli_scientifici/2006_cost-e29_Seismic%20Behaviour.pdf〉 (Feb. 18, 2014).
Crespell, P., and Gagnon, S. (2010). Cross laminated timber: A primer, FPInnovations, Pointe-Claire, QC, Canada.
FPInnovations and Binational Softwood Lumber Council. (2013). CLT handbook: Cross-laminated timber, Karacabeyli, E. and Douglas, B., eds., Pointe-Claire, QC, Canada.
Kim, H., Oh, J., Jeong, G., Yeo, H., and Lee, J. (2013). “Shear performance of PUR adhesive in cross laminating of red pine.” J. Korean Wood Sci. Technol., 41(2), 158–163.
Koch, P. (1972). Utilization of the southern pines, U.S. Dept. of Agriculture Forest Service, Washington, DC.
MGB Architecture and Design, Equilibrium Consulting, LMDG Limited, and BTY Group. (2012). “The case for tall wood buildings.” 〈http://wecbc.smallboxcms.com/database/rte/files/Tall%20Wood.pdf〉 (Jan. 7, 2014).
Morrison, C. (2010). “Green, clean technology to build touted in asheville-based partnership.” Asheville Citizen-Times, 〈http://www.citizen-times.com/article/20100523/NEWS/305230041/Green-clean-technology-build-touted-Asheville-based-partnership〉 (Jan. 7, 2014).
NIST. (2009). “Voluntary product standard PS 1-09 structural plywood.” National Institute of Standards and Technology, U.S. Dept. of Commerce, Gaithersburg, MD.
OpenEI. (2010). “Montana sustainable building systems.” Open EI Wiki, 〈http://en.openei.org/wiki/Montana_Sustainable_Building_Systems〉 (Jan. 7, 2014).
Robertson, A. (2007). “A comparative life cycle assessment of mid-rise office building construction alternatives: Laminated timber or reinforced concrete.” Master’s thesis, Univ. of Toronto, Toronto, ON, Canada.
Rose, A. K. (2012). “2010 forest inventory and analysis fact sheet.”, U.S. Dept. of Agriculture Forest Service, Asheville, NC.
Skidmore, Owings, and Merrill. (2013). “Timber Tower Research Project.” 〈http://www.som.com/ideas/research/timber_tower_research_project〉 (Jan. 18, 2014).
Southern Forest Products Association. (2013). Southern pine use guide, Kenner, LA, 〈http://www.culpeperwood.com/images/uploads/Southern_Pine_Use_Guide.pdf〉 (Jan. 23, 2014).
Ward, R. (2009). “Going to new heights—Building the world’s tallest mixed-use wood structure.” Structure, 〈http://www.structuremag.org/wp-content/uploads/2014/08/F-NewHeights-Ward-Aug091.pdf〉 (Jan. 7, 2014).
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Mar 3, 2014
Accepted: Sep 23, 2014
Published online: Nov 26, 2014
Discussion open until: Apr 26, 2015
Published in print: Sep 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.