Louisiana’s Experience with WMA Technologies: Mechanistic, Environmental, and Economic Analysis
Publication: Journal of Materials in Civil Engineering
Volume 27, Issue 6
Abstract
Warm mix asphalt (WMA) describes various technologies that allow asphalt mixtures to be produced at lower temperatures as compared to hot mix asphalt (HMA). WMA technologies also offer improvements in workability, cost, and environmental sustainability such as reduced fuel usage, greenhouse gas emissions, and wear and tear at plants, while enhancing worker health and safety conditions. These benefits, as well as the mechanical properties of WMA mixtures, need to be quantified and compared to that of HMA. The primary objective of this study was to evaluate the laboratory performance of plant-produced lab-compacted mixtures utilizing various WMA technologies. The secondary objective of this study was to compare WMA energy consumption cost and emission data to conventional HMA mixtures in terms of fuel/energy savings at the plant and in terms of CO and emissions. Three projects in Louisiana utilizing four different WMA technologies were considered in this study, yielding 11 mixtures total. Each project included a companion HMA mixture section to allow for direct comparison. Loose mixtures were obtained from trucks at the plant and compacted on-site in a mobile asphalt laboratory. Laboratory tests included dynamic modulus (), flow number (FN), loaded wheel tracking (LWT) test, indirect tensile (IDT) test, semicircular bend (SCB) test, thermal stress restrained specimen test (TSRST), and the Lottman moisture susceptibility test. Results indicated that WMA mixtures exhibit similar high and intermediate temperature performances in the laboratory as compared to HMA. On average, $1.61 of energy savings per ton of produced asphalt mixture was observed, along with a considerable reduction in air pollutants at the plant. However, the cost of additives and royalty fees would reduce the total cost savings from using WMA. These benefits were observed without reduction in the mechanistic performance of the mix.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the Louisiana Transportation Research Center in cooperation with the Louisiana Department of Transportation and Development. The contribution of the staff of the asphalt laboratory to this project is acknowledged.
References
Anderson, R. M., Baumgardner, G., May, R., and Reinke, G. (2008). “Engineering properties, emissions, and field performance of warm mix asphalt technologies.”, Transportation Research Board, National Research Council, Washington, DC.
Australian Asphalt Pavement Association. (2001). “Warm mix asphalt—A state of the art review.” Advisory Note 17.
Bonaquist, R. (2009). “Mix design practices for warm mix asphalt.”, Transportation Research Board, Washington, DC.
Bonaquist, R. (2011). “Mix design practices for warm-mix asphalt.”, The National Academies Press, Washington, DC.
Bonaquist, R. F., Christensen, D. W., and Stump, W. (2003). Simple performance tester for superpave mix design: First-article development and evaluation (vol. 513), Transportation Research Board, National Research Council, Washington, DC.
Button, J. W., Wimsatt, A., and Estakhri, C. (2007). “A synthesis of warm-mix asphalt.”, Texas Transportation Institute, College Station, TX.
D’Angelo, J. A., et al. (2008). “Warm-mix asphalt: European practice.”.
Diefenderfer, S., and Hearon, A. (2008). “Laboratory evaluation of a warm asphalt technology for use in Virginia.”.
Goh, S. W., You, Z., and Van Dam, T. J. (2007). “Laboratory evaluation and pavement design for warm mix asphalt.” Proc., Mid-Continent Transportation Research Symp., Iowa state univ., Ames, IA, 1–11.
Hassan, M. (2010). “Evaluation of the environmental and economic impacts of warm-mix asphalt using life-cycle assessment.” Int. J. Constr. Educ. Res., 6(3), 238–250.
Heijungs, R., and Suh, S. (2002). The computational structure of life cycle assessment, Springer.
Hurley, G. C., and Prowell, B. D. (2006a). “Evaluation of Evotherm for use in warm mix asphalt.”.
Hurley, G. C., and Prowell, B. D. (2006b). “Evaluation of potential processes for warm mix asphalt.”, National Center for Asphalt Technology, Auburn Univ., Auburn, AL.
ISO. (1997). “Environmental management—life cycle assessment—Principles and framework.”, International Organization for Standardization.
Kandhal, P. S. (2010). “Warm mix asphalt technologies: An overview.” J. Indian Roads Congr., 71(2), 143–152.
Lecomte, M., Deygout, F., and Menetti, A. (2007). “Emission and occupational exposure at lower asphalt production and laying temperatures.” WAM Environmental Benefits of Reducing Asphalt Production and Laying Temperature, Shell Bitumen, 〈www.static.shell.com/static/bitumen/downloads/wam_field_test_results_italy.Pdf〉.
Lippiat, B. (2007). Building for environmental and economic sustainability (BEES) technical manual and user guide, National Institute of Standards and Technology, Wellington, New Zealand.
Louisiana standard specifications for roads and bridges. (2006). Louisiana Dept. of Transportation and Development, Baton Rouge, LA.
Mohammad, L. N., Huang, B., and Abadie, C. (1998). “Performance evaluation of Louisiana’s superpave implementation projects utilizing the superpave shear tester.”.
Mohammad, L. N., Saadeh, S., Kabir, M., Othman, A. M., and Cooper, S. (2008). “Mechanistic properties of HMA mixtures containing hydrated lime.” Transportation Research Record 2051, Transportation Research Board, National Research Council, Washington, DC, 49–63.
Mohammad, L. N., Wu, Z., and Aglan, M. A. (2004). “Characterization of fracture and fatigue resistance on recycled polymer-modified asphalt pavements.” Proc., 5th Int. RILEM Conf. on Reflective Cracking in Pavements, RILEM publications, 375–382.
Mull, M. A., Othman, A., and Mohammad L. (2006). “Fatigue crack growth analysis of hot-mix asphalt employing the semi-circular notched bend specimen.” Transportation Research Board 85th Annual Meeting CD-ROM, Transportation Research Board (TRB).
Prowell, B. D., Hurley, G. C., and Crews, E. (2007). “Field performance of warm-mix asphalt at national center for asphalt technology test track.” Transp. Res. Rec.: J. Transp. Res. Board, 1998(1), 96–102.
Robinette, C., and Epps, J. (2010). “Energy, emissions, material conservation, and prices associated with construction, rehabilitation, and material alternatives for flexible pavement.” Transportation Research Board 2179, Transportation Research Record, Washington, DC, 10–22.
Russell, M., Uhlmeyer, J., Weston, J., Roseburg, J., Moomaw, T., and DeVol, J. (2009). “Evaluation of warm mix asphalt.”.
Wasiuddin, N. M., Selvamohan, S., Zaman, M. M., and Guegan, M. L. T. A. (2007). “Comparative laboratory study of sasobit and aspha-min additives in warm-mix asphalt.” Transp. Res. Rec.: J. Transp. Res. Board, 1998(1), 82–88.
Witczak, M. W., Kaloush, K., Pellinen, T., El-Basyouny, M., and Von Quintus, H. (2002). “Simple performance test for superpave mix design.”, National Research Council, Washington, DC.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jan 23, 2014
Accepted: Jun 9, 2014
Published online: Aug 13, 2014
Discussion open until: Jan 13, 2015
Published in print: Jun 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.