Analysis of Rutting Prediction Criteria Using a Nonlinear Viscoelastic Model
Publication: Journal of Materials in Civil Engineering
Volume 27, Issue 3
Abstract
Several prediction criteria have been proposed to rank asphalt binders based on their rutting performance, and each one has been shown to be able to predict rutting behavior observed in either accelerated loading field tests or under highway traffic with some level of success. In this study, an analysis of these rutting prediction criteria was conducted in order to identify the virtues and shortcomings of each. Asphalt binders that were used in the accelerated loading facility (ALF) study conducted by the Federal Highway Administration (FHWA) were obtained and studied. The experimental data obtained on these binders were fit with a nonlinear viscoelastic model so that it can be used to predict their response under different loading conditions. By comparing predicted behavior based on the nonlinear viscoelastic model and the various rutting prediction criteria, the part of the complex nonlinear mechanical behavior of these binders that each criterion addresses was determined. Results show that each criterion represents the resistance offered by asphalt binders to permanent strain over a specific range of stresses. Results also show that a simple viscosity test might be sufficient to characterize the rutting performance of asphalt binders accurately.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors thank Dr. Nelson Gibson and the FHWA for materials and information, and Dr. Eyad Masad for his comments on a previous draft.
References
Anderson, R., D’Angelo, J., and Bukowski, J. (2011). “Evaluation of the MSCR test for Canadian asphalt binders.” 56th Annual Conf. Canadian Technical Asphalt Association, Tranportation Association of Canada, Ottawa, ON, Canada.
Bahia, H., Hanson, D., Zeng, M., Zhai, H., Khatri, M., and Anderson, R. (2001a). “Characterization of modified asphalt binders in Superpave mix design.”, National Cooperative Highway Research Program, Washington, DC.
Bahia, H., Zhai, H., Zeng, M., Hu, Y., and Turner, P. (2001b). “Development of binder specification parameters based on characterization of damage behavior.” J. Assoc. Asphalt Paving Technol., 70, 442–470.
Barksdale, R. (1971). “Compressive stress pulse times in flexible pavements for use in dynamic testing.” Highway Res. Rec., 345, 32–44.
Bouldin, M., Dongré, R., and D’Angelo, J. (2001). “Proposed refinement of Superpave high-temperature specification parameter for performance-graded binders.” Transp. Res. Rec.: J. Transp. Res. Board, 1766, 40–47.
D’Angelo, J., Kluttz, R., Dongre, R., Stephens, K., and Zanzotto, L. (2007). “Revision of the Superpave high-temperature binder specification: The multiple stress creep recovery test.” J. Assoc. Asphalt Paving Technol., 76, 123–162.
D’Angelo, J. A. (2009). “The relationship of the MSCR test to rutting.” Road Mater. Pavement Des., 10(1), 61–80.
Delgadillo, R., Cho, D., and Bahia, H. (2006). “Nonlinearity of repeated creep and recovery binder test and relationship with mixture permanent deformation.” Transp. Res. Rec.: J. Transp. Res. Board, 1962, 3–11.
Dongré, R., Button, J., Kluttz, R., and Anderson, D. (1997). “Evaluation of Superpave binder specification with performance of polymer-modified asphalt pavements.” ASTM Special Technical Publication, Vol. 1322, American Technical Publisher, Orland Park, IL, 80–100.
Dongré, R., and D’Angelo, J. (2003). “Refinement of Superpave high-temperature binder specification based on pavement performance in the accelerated loading facility.” Transp. Res. Rec.: J. Transp. Res. Board, 1829, 39–46.
Gibson, N., et al. (2012). “Full-scale accelerated performance testing for superpave and structural validation.”, Federal Highway Administration, Washington, DC.
Golalipour, A. (2011). “Modification of multiple stress creep and recovery test procedure and usage in specification.” M.S. thesis, Univ. of Wisconsin, Madison, WI.
Masad, E., Huang, C., D’Angelo, J., and Little, D. (2009). “Characterization of asphalt binder resistance to permanent deformation based on nonlinear viscoelastic analysis of multiple stress creep recovery (MSCR) test.” J. Assoc. Asphalt Paving Technol., 78, 535–566.
Merusi, F., and Giuliani, F. (2011). “Intrinsic resistance to nonreversible deformation in modified asphalt binders and its relation with specification criteria.” Constr. Build. Mater., 25(8), 3356–3366.
Motamed, A., and Bahia, H. U. (2011). “Influence of test geometry, temperature, stress level, and loading duration on binder properties measured using DSR.” J. Mater. Civ. Eng., 1422–1432.
Narayan, S. P. A., Little, D. N., and Rajagopal, K. R. (2013). “A nonlinear viscoelastic model for describing the response of asphalt binders within the context of a Gibbs-potential based thermodynamic framework.” J. Eng. Mech., 04014116.
Phillips, M., and Robertus, C. (1996). “Binder rheology and asphaltic pavement permanent deformation: The zero-shear-viscosity.” Eurasphalt Eurobitume Cong., European Asphalt Pavement Association, Brussels, Belgium.
Rowe, G., D’Angelo, J., and Sharrock, M. (2002). “Use of zero shear viscosity as a parameter for the high-temperature binder specification parameter.” J. Appl. Asphalt Binder Technol., 2(2).
Shenoy, A. (2001). “Refinement of the Superpave specification parameter for performance grading of asphalt.” J. Transp. Eng., 357–362.
Shenoy, A. (2004a). “A comprehensive treatise of the high-temperature specification parameter—/(1-(1/tan d sin d)) for performance grading of asphalts.” Appl. Rheol., 14(6), 303–314.
Shenoy, A. (2004b). “High temperature performance grading of asphalts through a specification criterion that could capture field performance.” J. Transp. Eng., 130(1), 132–137.
Stuart, K., Mogawer, W., and Romero, P. (1999). “Validation of asphalt binder and mixture tests that measure rutting susceptibility using the accelerated loading facility.”, Federal Highway Administration, Washington, DC.
Sybilski, D. (1996). “Zero-shear viscosity of bituminous binder and its relation to bituminous mixture’s rutting resistance.” Transp. Res. Rec.: J. Transp. Res. Board, 1535, 15–21.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Nov 5, 2013
Accepted: Mar 5, 2014
Published online: Jul 21, 2014
Discussion open until: Dec 21, 2014
Published in print: Mar 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.