Bond Stress-Slip Behavior: Case of GFRP Bars in Geopolymer Concrete
Publication: Journal of Materials in Civil Engineering
Volume 27, Issue 1
Abstract
The use of geopolymer concrete reinforced with fiber-reinforced polymer (FRP) bars is anticipated to address the concerns on the usage of traditional reinforced concrete structures, such as the corrosion of internal steel reinforcement, costly repair and rehabilitation, and development of sustainable infrastructures. To gain wide acceptance in the construction market, the bond between geopolymer concrete and the FRP bar should be investigated first because it is a critical factor that influences the behavior of structures, specifically its strength and long-term durability. In this study, the bond performance of sand-coated glass fiber-reinforced polymer (GFRP) bars into geopolymer concrete with a compressive strength of 33 MPa was investigated under a direct pullout test. The effects of parameters such as bar diameter (12.7, 15.9, and 19.0 mm) and embedment length (5, 10, and 15 , where is the bar diameter) were evaluated. The results showed that the maximum average bond stress obtained is around 23 MPa. As GFRP bar diameter increases, the average bond stress decreases. Similarly, the average bond stress decreases as the bond length becomes longer. The specimens with shorter embedment length failed because of pullout of the bars, whereas those with longer embedment lengths failed because the concrete split. The results further revealed that the geopolymer concrete reinforced with GFRP bars have a bond strength similar to that of steel-reinforced geopolymer concrete. Finally, bond-slip models for the ascending branch up to maximum bond stress of the bond-slip curves for GFRP bars and geopolymer concrete were proposed.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge V-Rod Australia for the materials and technical support they had given in the conduct of this research undertaking.
References
Achillides, A., and Pilakoutas, K. (2004). “Bond behaviour of fiber reinforced polymer bars under direct pullout conditions.” J. Compos. Constr., 173–181.
Aldred, J., and Day, J. (2012). “Is geopolymer concrete a sustainable alternative to traditional concrete?” 37th Conf. on Our World in Concrete & Structures, CI-Premier Pte, Singapore, 1–14.
American Concrete Institute (ACI). (2004). “Guide test methods for FRPs for reinforcing or strengthening concrete structures.”, Farmington Hills, MI, 10–13.
American Concrete Institute (ACI). (2006). “Guide for the design and construction of concrete reinforced with FRP bars.”, Farmington Hills, MI, 44.
Arias, J. P. M., Vasquez, A., and Escobar, M. M. (2012). “Use of sand coating to improve bonding between GFRP bars and concrete.” J. Compos. Mater., 46(18), 2271–2278.
Baena, M., Torres, L., Turon, A., and Barris, C. (2009). “Experimental study of bond behaviour between concrete and FRP bars using a pull-out test.” Compos. Part B, 40(8), 784–797.
Bakis, C. E., Uppuluri, V. S., Nanni, A., and Boothby, T. E. (1998). “Analysis of bonding mechanisms of smooth and lugged FRP rods embedded in concrete.” Compos. Sci. Technol., 58(8), 1307–1319.
Canadian Standards Association (CSA). (2010). “Specification for fibre-reinforced polymers.”, Rexdale, ON, Canada.
Chaallal, O., and Benmokrane, B. (1993). “Pullout and bond of glass-fibre rods embedded in concrete and cement grout.” Mater. Struct., 26(3), 167–175.
Cosenza, E., Manfredi, G., and Realfonzo, R. (1997). “Behavior and modeling of bond of FRP rebars to concrete.” J. Compos. Constr., 40–51.
Davidovits, J. (1988). “Geopolymer chemistry and applications.” Proc., Geopolymer ’88, 1st European Conf. on Soft Mineralurgy, The Geopolymer Institute, Compiegne, France, 25–48.
Duxson, P., Fernandez-Jimenez, A., Provis, L., Lukey, G. C., Palomo, A., and van Deventer, J. S. J. (2007). “Geolpolymer technology: The current state of the art.” J. Mater. Sci., 42(9), 2917–2933.
Fico, R. (2008). “Limit states design of concrete structures reinforced with FRP bars.” Ph.D. thesis, Univ. of Naples Federico II, Naples, Italy.
Gangarao, H. V. S., Taly, N., and Vijay, P. V. (2007). Reinforced concrete design with FRP composites, CRC Press, Taylor & Francis Group, Boca Raton, FL.
Lloyd, N. A., and Rangan, B. V. (2010). “Geopolymer concrete: A review of development and opportunities.” 35th Conf. on Our World in Concrete & Structures, CI-Premier Pte, Singapore, 1–8.
Malvar, L. J. (1994). “Bond stress-slip characteristics of FRP rebars.”, Naval Facilities Engineering Service Center, Port Hueneme, CA.
Mazaheripour, H., Barros, J. A. O., Sena-Cruz, J. M., Pepe, M., and Martinelli, E. (2013). “Experimental study on the bond performance of GFRP bars in self-compacting steel fiber reinforced concrete.” Compos. Struct., 95, 202–212.
McCaffrey, R. (2002). “Climate change and the cement industry.” Global Cem. Lime Mag., 15–19.
McLellan, B. C., Williams, R. P., Lay, J., Riessen, A., and Corder, G. D. (2011). “Costs and carbon emissions for geopolymer pastes in comparison to ordinary portland cement.” J. Cleaner Prod., 19(9–10), 1080–1090.
Okelo, R., and Yuan, R. L. (2005). “Bond strength of fiber reinforced polymer rebars in normal strength concrete.” J. Compos. Constr., 203–213.
Sarker, P. K. (2011). “Bond strength of reinforcing steel embedded in fly ash-based geopolymer concrete.” Mater. Struct., 44(5), 1021–1030.
Selby, D. R. (2011). “An investigation into the bond of steel reinforcement in geopolymer and ordinary Portland cement concrete.” Bachelor thesis, School of Civil Engineering, Univ. College, Univ. of New South Wales–ADFA, Canberra, Australia.
Sofi, M., van Deventer, J. S. J., and Mendis, P. A. (2007). “Bond performance of reinforcing bars in inorganic polymer concrete (IPC).” J. Mater. Sci., 42(9), 3107–3116.
Tang, W. C., Lo, T. Y., and Balendran, R. V. (2008). “Bond performance of polystyrene aggregate concrete (PAC) reinforced with glass-fibre-reinforced polymer (GFRP) bars.” Build. Environ., 43(1), 98–107.
Tao, S., Ehsani, M. R., and Saadatmanesh, H. (1992). “Bond strength of straight GFRP rebars.” Material Performance and Prevention of Deficiencies and Failures, in Proc., Materials Engineering Congress, ASCE, Reston, VA, 598–605.
Tastani, S. P., and Pantazopulou, S. J. (2006). “Bond of GFRP bars in concrete: Experimental study and analytical interpretation.” J. Compos. Constr., 381–391.
Tastani, S. P., and Pantazopulou, S. J. (2010). “Direct tension pullout bond test: Experimental results.” J. Struct. Eng., 731–743.
Tighiouart, B., Benmokrane, B., and Gao, D. (1998). “Investigation of bond in concrete members with fibre reinforced polymer (FRP) bars.” Constr. Build. Mater., 12(8), 453–462.
Zhang, B., and Benmokrane, B. (2002). “Pullout bond properties of fiber-reinforced polymer tendons to grout.” J. Mater. Civ. Eng., 399–408.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Dec 3, 2013
Accepted: Jan 30, 2014
Published online: Jan 31, 2014
Discussion open until: Dec 11, 2014
Published in print: Jan 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.