High-Strength Lightweight SCC Matrix with Partial Normal-Weight Coarse-Aggregate Replacement: Strength and Durability Evaluations
Publication: Journal of Materials in Civil Engineering
Volume 26, Issue 11
Abstract
Lightweight coarse aggregate from five sources found in the United Arab Emirates (UAE) were previously evaluated. The evaluation focused on influence of the physical properties of the aggregates on strength development. Target unit weight less than , compressive strength of 40 MPa or higher, and achieving the flowability requirements for self-consolidating concrete (SCC) were the evaluation criteria considered during the development. Aggregate from three sources met the evaluation criteria; however, one of the sources was no longer available in UAE. Therefore, an extensive investigation was conducted to evaluate properties of the other two sources, especially durability related properties. In this paper, results of the compressive, flexure, splitting tensile strength, and modulus of elasticity are presented and discussed. In addition, scanning electron microscope (SEM) scans and rapid chloride permeability tests (RCPT) were conducted. Results showed that both sources met the requirements for structural applications. However, one source showed better performance in all tests, which was supported by the examination of the microstructure of the hardened concrete.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research effort is a part of the American University of Sharjah’s Provost’s Challenge Grant, 2011 and faculty research grant (FRG10-27). The financial support provided by the Office of Research and Graduate Studies at the American University of Sharjah is greatly appreciated.
References
Akcay, B., and Tasdemir, M. A. (2009). “Optimisation of using lightweight aggregates in mitigating autogenous deformation of concrete.” Constr. Build. Mater., 23(1), 353–363.
Akcay, B., and Tasdemir, M. A. (2010). “Effects of distribution of lightweight aggregates on internal curing of concrete.” Cem. Concr. Compos., 32(8), 611–616.
American Concrete Institute (ACI). (2007). “Self-consolidating concrete.” ACI 237, Farmington Hills, MI.
American Concrete Institute (ACI). (2011). “Building code requirements for structural concrete and commentary.” ACI 318, Farmington Hills, MI.
ASTM. (2006). “Standard test method for resistance to degradation of small-size coarse aggregate by abrasion and impact in the los angeles machine.” ASTM C131, West Conshohocken, PA.
ASTM. (2009a). “Standard specifications for lightweight aggregates for structural applications.” ASTM C330/330M, West Conshohocken, PA.
ASTM. (2009b). “Standard test method for bulk density (“Unit Weight”) and voids in aggregate.” ASTM C29/C29M, West Conshohocken, PA.
ASTM. (2010a). “Standard test method for flexural strength of concrete (using simple beam with third-point loading).” ASTM C78/C78M—10e1, West Conshohocken, PA.
ASTM. (2010b). “Standard test method for static modulus of elasticity and Poisson’s ratio of concrete in compression.” ASTM C469/C469M, West Conshohocken, PA.
ASTM. (2011a). “Standard test method for determining density of structural lightweight concrete.” ASTM C567/C567M, West Conshohocken, PA.
ASTM. (2011b). “Standard test method for splitting tensile strength of cylindrical concrete specimens.” ASTM C496/C496M, West Conshohocken, PA.
ASTM. (2012a). “Standard test method for density, relative density (specific gravity), and absorption of coarse aggregate.” ASTM C127, West Conshohocken, PA.
ASTM. (2012b). “Standard test method for electrical indication of concrete’s ability to resist chloride ion penetration.” ASTM C1202, West Conshohocken, PA.
ASTM. (2013). “Standard specification for concrete aggregates.” ASTM C33/C33M, West Conshohocken, PA.
British Standards Institute. (2010). “Tests for mechanical and physical properties of aggregates: Methods for the determination of resistance to fragmentation.” BSI EN 1097-2, London.
British Standards Institute. (2009). “Compressive strength of test specimens.” BSI EN 12390-3, London.
Browning, J., Darwin, D., Reynolds, D., and Pendergrass, B. (2011). “Lightweight aggregate as internal curing agent to limit concrete shrinkage.” ACI Mater. J., 108(6), 638–644.
Chen, B., and Liu, J. (2008). “Experimental application of mineral admixtures in lightweight concrete with high strength and workability.” Constr. Build. Mater., 22(6), 1108–1113.
Cui, H., Lo, T. Y., and Xing, F. (2010). “The effect of slag on durability of lightweight concrete.” Paper presented at the RILEM-2nd Int. Symp. on Service Life Design for Infrastructures, RILEM Publications, France, 741–747.
Cui, H. Z., Lo, T. Y., Memon, S. A., and Xu, W. (2012). “Effect of lightweight aggregates on the mechanical properties and brittleness of lightweight aggregate concrete.” Constr. Build. Mater., 35(9), 149–158.
Gesoğlu, M., Özturan, T., and Güneyisi, E. (2006). “Effects of cold-bonded fly ash aggregate properties on the shrinkage cracking of lightweight concretes.” Cem. Concr. Compos., 28(7), 598–605.
Guneyisi, E., Gesoglu, M., and Mermerdas, K. (2008). “Improving strength, drying shrinkage, and pore structure of concrete using metakaolin.” Mater. Struct., 41(5), 937–949.
Haque, M. N., Al-Khaiat, H., and Kayali, O. (2004). “Strength and durability of lightweight concrete.” Cem. Concr. Compos., 26(4), 307–314.
Henkensiefken, R., Bentz, D., Nantung, T., and Weiss, J. (2009). “Volume change and cracking in internally cured mixtures made with saturated lightweight aggregate under sealed and unsealed conditions.” Cem. Concr. Compos., 31(7), 427–437.
Hossain, K. M. A., and Ahmed, S. (2011). “Lightweight concrete incorporating volcanic ash-based blended cement and pumice aggregate.” J. Mater. Civ. Eng., 493.
Hossain, K. M. A., and Lachemi, M. (2007). “Mixture design, strength, durability, and fire resistance of lightweight pumice concrete.” ACI Mater. J., 104(5), 449–457.
Hwang, C. L., and Hung, M. F. (2005). “Durability design and performance of self-consolidating lightweight concrete.” Constr. Build. Mater., 19(8), 619–626.
Kabay, N., and Aköz, F. (2012). “Effect of prewetting methods on some fresh and hardened properties of concrete with pumice aggregate.” Cem. Concr. Compos., 34(4), 503–507.
Karahan, O., Hossain, K. M. A., Ozbay, E., Lachemi, M., and Sancak, E. (2012). “Effect of metakaolin content on the properties self-consolidating lightweight concrete.” Constr. Build. Mater., 31(6), 320–325.
Katkhuda, H., Hanayneh, B., and Shatarat, N. (2009). “Influence of silica fume on high strength lightweight concrete.” World Acad. Sci. Eng. Technol., 3(10), 767–774.
Kim, H. K., Jeon, J. H., and Lee, H. K. (2012). “Workability, and mechanical, acoustic and thermal properties of lightweight aggregate concrete with a high volume of entrained air.” Constr. Build. Mater., 29(4), 193–200.
Kılıç, A., Atiş, C. D., Yaşar, E., and Özcan, F. (2003). “High-strength lightweight concrete made with scoria aggregate containing mineral admixtures.” Cem. Concr. Res., 33(10), 1595–1599.
Kockal, N. U., and Ozturan, T. (2010). “Effects of lightweight fly ash aggregate properties on the behavior of lightweight concretes.” J. Hazard. Mater., 179(1–3), 954–965.
Kockal, N. U., and Ozturan, T. (2011). “Durability of lightweight concretes with lightweight fly ash aggregates.” Constr. Build. Mater., 25(3), 1430–1438.
Kok-Seng, C., Chen-Chung, K., and Min-Hong, Z. (2005). “Stability of fresh lightweight aggregate concrete under vibration.” ACI Mater. J., 102(5), 347.
Kucharczyková, B., Keršner, Z., Pospíchal, O., Misák, P., Daněk, P., and Schmid, P. (2012). “The porous aggregate pre-soaking in relation to the freeze–thaw resistance of lightweight aggregate concrete.” Constr. Build. Mater., 30(5), 761–766.
Lindgård, J., Andiç-Çakır, Ö., Fernandes, I., Rønning, T. F., and Thomas, M. D. A. (2012). “Alkali–silica reactions (ASR): Literature review on parameters influencing laboratory performance testing.” Cem. Concr. Res., 42(2), 223–243.
Lo, T. Y., and Cui, H. Z. (2004). “Effect of porous lightweight aggregate on strength of concrete.” Mater. Lett., 58(6), 916–919.
Lo, T. Y., Cui, H. Z., Tang, W. C., and Leung, W. M. (2008). “The effect of aggregate absorption on pore area at interfacial zone of lightweight concrete.” Constr. Build. Mater., 22(4), 623–628.
Mirza, F. (2009). “Effect of sand replacement and silica fume addition on chloride ion permeability of lightweight concrete.” JKAU Eng. Sci., 20(1), 61–73.
Mladenovič, A., Šuput, J. S., Ducman, V., and Škapin, A. S. (2004). “Alkali–silica reactivity of some frequently used lightweight aggregates.” Cem. Concr. Res., 34(10), 1809–1816.
Neville, A. M. (1996). Properties of concrete, 4th Ed., Wiley, New York, NY.
Ozyildirim, C. (2008). “Durability of structural lightweight concrete.” Paper presented at the Concrete Bridge Conf., ESCSI, Chicago.
Polat, R., Demirboğa, R., and Karakoç, M. B., and Türkmen, İ. (2010). “The influence of lightweight aggregate on the physico-mechanical properties of concrete exposed to freeze–thaw cycles.” Cold Reg. Sci. Technol., 60(1), 51–56.
Shannag, M. J. (2011). “Characteristics of lightweight concrete containing mineral admixtures.” Constr. Build. Mater., 25(2), 658–662.
Topcu, I., and Uygunoğlu, T. (2010). “Effect of aggregate type on properties of hardened self-consolidating lightweight concrete (SCLC).” Constr. Build. Mater., 24(7), 1286–1295.
Wang, H. Y. (2007). “Study on durability of densified high-performance lightweight aggregate concrete.” Comput. Concr., 4(6), 499–510.
Wang, H. Y. (2009). “Durability of self-consolidating lightweight aggregate concrete using dredged silt.” Constr. Build. Mater., 23(6), 2332–2337.
Yasar, E., Atis, C. D., Kilic, A., and Gulsen, H. (2003). “Strength properties of lightweight concrete made with basaltic pumice and fly ash.” Mater. Lett., 57(15), 2267–2270.
Yehia, S., Abudayyeh, O., Bhusan, B., Maurovich, M., and Zalt, A. (2009). “Self-consolidating concrete mixture with local materials: Proportioning and evaluation.” Mater. Sci. Res. J., 3(1–2), 41–64.
Zhou, F. P., Barr, B. I. G., and Lydon, F. D. (1995). “Effect of coarse aggregate on elastic modulus and compressive strength of high performance concrete.” Cem. Concr. Res., 25(1), 177–186.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jun 5, 2013
Accepted: Nov 25, 2013
Published online: Jun 16, 2014
Published in print: Nov 1, 2014
Discussion open until: Nov 16, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.