Fatigue Properties of Asphalt Materials at Low In-Service Temperatures
Publication: Journal of Materials in Civil Engineering
Volume 25, Issue 9
Abstract
Fatigue damage is one of the most common distresses observed in the asphalt-concrete pavements. Both the initiation and propagation of fatigue cracking are complicated and very difficult to detect because they develop generally within pavement structure. To understand the fatigue performance of asphalt concrete thoroughly, the behaviors of the major components of asphalt concrete under cyclic loading were investigated in this study. A new experimental method was developed to evaluate the performance of asphalt binder, mastic, and fine-aggregates mixture under cyclic tensile loading. The test results showed that fatigue performance of asphalt binder is closely related to the loading magnitude, temperature, and loading frequency. Mastic specimens with varied filler contents were tested. It was found that the mastic specimen with 30% filler content had better fatigue resistance and higher permanent strain. The differences between the test results of mastic and mixture were then compared and analyzed using X-ray tomography imaging. It was indicated that the fatigue resistance is closely related to the air-void content of the specimens. Three-dimensional digital specimens of asphalt binder, mastic, and mixture were developed and tested in the numerical simulation of fatigue tests based on the finite-element method. Both mastic and mixture were modeled as heterogeneous composite materials in which the asphalt binder, filler, and aggregate were described by different mechanical models. Fatigue damage of asphalt concrete was simplified by a damage model, which characterizes the degradation of the elastic modulus of the asphalt binder. It was found that with proper selection of damage parameters, the simulation results agree well with laboratory test results and can be used as a basis for future fatigue research. Finally, the reinforcement effect of basalt fiber was evaluated as an additive to improve the fatigue resistance of asphalt-binding materials. It was found that with proper content, the fatigue resistances of asphalt binder and mastic were significantly improved. The numerical simulation analysis also showed that fibers release the stress concentration in the interface area of two fillers and mitigate the fatigue damage caused by cyclic loading.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (2007). “Standard method of test for determining the fracture properties of asphalt binder in direct tension (DT).”, Washington, DC.
Abdulshafi, A. A., and Majidzadeh, K. (1985). “J-integral and cyclic plasticity approach to fatigue and fracture of asphaltic mixtures.” Transp. Res. Rec., (1034), 112–123.
Aglan, H. A., and Figueroa, J. L. (1993). “Damage-evolution approach to fatigue cracking in pavements.” J. Eng. Mech., 119(6), 1243–1259.
Anderson, D. A., Le Hir, Y. M., Marasteanu, M. O., Planche, J.-P., Martin, D., and Gauthier, G. (2001). “Evaluation of fatigue criteria for asphalt binders.” J. Transp. Res. Rec., 1766, 48–55.
Bay, B., Smith, T., Fyhrie, D., and Saad, M. (1999). “Three-dimensional strain mapping using X-ray tomography.” Exp. Mech., 39(3), 217–226.
Bodin, D., Pijaudier-Cabot, G., De La Roche, C., Piau, J.-M., Chabot, A. (2004). “Continuum damage approach to asphalt concrete fatigue modeling.” J. Eng. Mech., 130(6), 700–709.
Bonnetti, K. S., Nam, K., and Bahia, H. U. (2002). “Measuring and defining fatigue behavior of asphalt binders.” Transp. Res. Rec., 1810(1), 33–43.
Button, J. W., Little, D. N., Kim, Y., and Ahmed, J. (1987). “Mechanistic evaluation of selected asphalt additives.” Proc., Association of Asphalt Paving Technologies, 56, 62–90.
Carpenter, S. H., and Shen, S. (2006). “Dissipated energy approach to study hot-mix asphalt healing in fatigue.” Transp. Res. Rec., 1970(1), 178–185.
Castro, M., and Sanchez, J. A. (2007). “Damage based model for prediction of asphalt concrete fatigue curves.” J. Mater. Civ. Eng., 19(8), 700–702.
Chehab, G. R., Seo, Y., and Kim, Y. R. (2007). “Viscoelastoplastic damage characterization of asphalt-aggregate mixtures using digital image correlation.” Int. J. Geomech., 7(2), 111–118.
Daniel, J. S., and Bisirri, W. M. (2005). “Characterizing fatigue in pavement materials using a dissipated energy parameter.” Proc., Sessions of the Geo-Frontiers 2005 Congress, Austin, TX, ASCE, 199–208.
Darveaux, R. (2000). “Effect of simulation methodology on solder joint crack growth correlation.” Proc., Electronic Components and Technology Conf., IEEE, Las Vegas, 1048–1058.
Deacon, J. A., Harvey, J. T., Tayebali, A., and Monismith, C. L. (1997). “Influence of binder loss modulus on pavement fatigue performance of asphalt concrete pavement.” Assoc. Asphalt Paving Technol., 66, 633–685.
El-Basyouny, M. M., and Witczak, M. (2005). “Calibration of alligator fatigue cracking model for 2002 design guide.” Transp. Res. Rec., 1919(2), 77–86.
Epps, J., and Monismith, C. L. (1969). “Influence of mixture variables on the flexural fatigue properties of asphalt concrete.” Asphalt Pav. Technol., 38, 423–464.
Ghuzlan, K. A., and Carpenter, S. H. (2003). “Traditional fatigue analysis of asphalt concrete mixtures.” Presentation submitted to the 82nd Annual Meeting of the Transportation Research Board, Washington, DC.
Harvey, J., and Tsai, B.-W. (1996). “Effects of asphalt content and air void content on mix fatigue and stiffness.” Transp. Res. Rec., 1543(1), 38–45.
Huang, C., Najjar, Y. M., and Romanoschi, S. (2007). “Predicting the asphalt concrete fatigue life using artificial neural network approach.” 82nd Annual Meeting of the Transportation Research Board, Washington, DC.
Kim, Y.-R., Little, D., and Song, I. (2003). “Effect of mineral fillers on fatigue resistance and fundamental material characteristics: Mechanistic evaluation.” Transp. Res. Rec., 1832(1), 1–8.
Lee, H.-J., Daniel, J. S., and Kim, Y. R. (2000). “Continuum damage mechanics-based fatigue model of asphalt concrete.” J. Mater. Civ. Eng., 12(2), 105–112.
Lemaitre, J., and Chaboche, J. L. (1990). Mechanics of solid materials, Cambridge University Press, Cambridge.
Ludovico, M. D., Prota, A., and Manfredi, G. (2010). “Structural upgrade using basalt fibers for concrete confinement.” J. Compos. Constr., 14(5), 541–552.
Majidzadeh, K., Kauffman, E. M., and Saraf, C. L. (1972). “Analysis of fatigue of paving mixtures from fracture mechanics viewpoint.”, ASTM, West Conshohocken, PA, 67–83.
Monismith, C. L., Epps, J. A., Kasianchuk, D. A., and Mclean, D. B. (1971). “Asphalt mixture behavior in repeated flexure.”, Univ. of California, Berkeley, CA.
Mull, M. A., Stuart, K., and Yehia, A. (2002). “Fracture resistance characterization of chemically modified crumb rubber asphalt pavement.” J. Mater. Sci., 37(3), 557–566.
Ramakrishnan, V., Tolmare, N. S., and Brik, V. B. (1998). “Performance evaluation of 3-D basalt fiber reinforced concrete & basalt rod reinforced concrete.”.
Ramsamooj, D. V. (1999). “Prediction of fatigue performance of asphalt concrete mixes.” J. Test. Eval., 27(5), 3343–3348.
Rodrigues, R. M. (2000). “A model for fatigue cracking prediction of asphalt pavements based on mixture bonding energy.” Int. J. Pav. Eng., 1(2), 133–149.
Shenoy, A. (2002). “Fatigue testing and evaluation of asphalt binders using the dynamic shear rheometer.” J. Test. Eval., 30(4), 303–312.
Si, Z., Little, D. N., and Lytton, R. L. (2002). “Characterization of microdamage and healing of asphalt concrete mixtures.” J. Mater. Civ. Eng., 14(6), 461–470.
Sim, J., Park, C., and Moon, D. Y. (2005). “Characteristics of basalt fiber as a strengthening material for concrete structures.” Compos. Part B, 36(6–7), 504–512.
Simulia, Inc. (2011). ABAQUS analysis users’ manual, Asphalt Material Lab of Virginia Tech Transportation Institute.
Smith, B., and Hesp, S. (2000). “Crack pinning in asphalt mastic and concrete: Regular fatigue studies.” Transp. Res. Rec., 1728(1), 75–81.
Sousa, J. B., Pais, J. C., Prates, M., Barros, R., Langlois, P., and Leclerc, A.-M. (2007). “Effect of aggregate gradation on fatigue life of asphalt concrete mixes.” Transp. Res. Rec., 1630(1998), 62–68.
Sousa, J. B., Tayebali, A. A., Harvey, J. T., Hendricks, P., and Monismith, C. L. (1993). “Sensitivity of SHRP-A003A testing equipment to mix design parameters for permanent deformation and fatigue.” Annual Meeting of the Transportation Research Board, Washington, DC.
Sulaiman, S. J., and Stock, A. F. (1995). “The use of fracture mechanics for the evaluation of asphalt mixes.” Assoc. Asphalt Pav. Technol., 64, 500–533.
Suo, Z., and Wong, W. G. (2009). “Analysis of fatigue crack growth behavior in asphalt concrete material in wearing course.” Constr. Build. Mater., 23(1), 462–468.
Tayebali, A. A. (1994). “Fatigue reponse of asphalt-aggregate mixtures.”, Strategic Highway Research Program, National Research Council, Washington, DC.
Tigdemir, M., Karasahin, M., and Sen, Z. (2001). “Investigation of fatigue behaviour of asphalt concrete pavements with fuzzy-logic approach.” Int. J. Fatigue, 24(8), 903–910.
Wang, D. (2011). “A micro-scale method to associate the fatigue properties of asphalt binder, mastic and mixture.” Ph.D. dissertation, Virginia Tech, Blacksburg, VA.
Wang, L., Frost, J. D., and Shashidhar, N. (2001). “Microstructure study of wes track mixes from X-ray tomography images.” Transp. Res. Rec., 1767(1), 85–94.
Wang, L., Frost, J. D., Voyiadjis, G., and Harman, T. P. (2003). “Quantification of damage parameters using X ray tomography images.” J. Mech. Mater., 35(8), 777–790.
Wang, L., Paul, H. S., Harman, T., and Anglo, J. D. (2004). “Characterization of aggregate and asphalt concrete using X ray tomography.” Assoc. Asphalt Pav. Technol., 73, 467–500.
Wen, H., and Bahia, H. (2009). “Characterizing fatigue of asphalt binders with viscoelastic continuum damage mechanics.” Transp. Res. Rec., 2126(1), 55–62.
You, Z., Adhikari, S., and Kutay, M. E. (2009). “Dynamic modulus simulation of the asphalt concrete using the X-ray computed tomography images.” Mater. Struct. (Dordrecht, Neth.), 42(5), 617–630.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Mar 6, 2012
Accepted: Sep 19, 2012
Published online: Sep 22, 2012
Discussion open until: Feb 22, 2013
Published in print: Sep 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.