Use of Surface Free Energy Method to Evaluate Effect of Hydrate Lime on Moisture Damage in Hot-Mix Asphalt
Publication: Journal of Materials in Civil Engineering
Volume 25, Issue 8
Abstract
One of the convenient approaches to decreasing moisture sensitivity in hot-mix asphalt (HMA) is coating the aggregate surface with a suitable agent. Hydrate lime (HL) is the most common antistrip additive used to treat aggregate properties in hot-mix asphalt. In this study, the effect of HL-treated aggregate on moisture sensitivity of HMA was evaluated by applying thermodynamic concepts and surface free energy (SFE) method. The SFE components of aggregates and asphalt binders were evaluated by using a universal sorption device (USD) and dynamic Wilhelmy plate method (DWPM), respectively. The results showed that the use of HL reduced the acid SFE and increased the base SFE of the two types of aggregates used in this study. These changes promote adhesion between asphalt binder and aggregate with and without water, particularly in the mixtures containing acidic aggregates prone to moisture damage. Covering the aggregate with HL decreased the total SFE of aggregate, leading to the increase in wetability of asphalt binder over the aggregate. Moreover, HL decreased the difference between surface free energies of asphalt-aggregate and water-aggregate, decreasing the detachment tendency of asphalt binder over the aggregates. Finally, the treatment of aggregate surface with HL reduced the difference between the free energy of adhesion of aggregate-asphalt binder in dry and wet conditions, decreasing the rate of moisture damage.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (2004). “Standard method of test for resistance of compacted hot mix asphalt (HMA) to moisture-induced damage.” T283, Washington, DC.
Arabani, M., and Hamedi, Gh. H. (2011). “Using the surface free energy method to evaluate the effects of polymeric aggregate treatment on moisture damage in hot mix asphalt.” J. Mater. Civ. Eng., 23(6), 802–811.
ASTM. (1976). “Standard test method for density of semi-solid bituminous materials (pycnometer method).” D70-76, West Conshohocken, PA.
ASTM. (1978a). “Standard test method for penetration of bituminous materials.” D5-73, West Conshohocken, PA.
ASTM. (1978b). “Flash and fire points by cleveland open cup.” D92-78, West Conshohocken, PA.
ASTM. (1978c). “Standard test method for effect of heat and air on asphaltic materials (thin-film oven test).” D1754-78, West Conshohocken, PA.
ASTM. (1981a). “Standard test method for solubility of asphalt materials in trichloroethylene.” D2042-76, West Conshohocken, PA.
ASTM. (1981b). “Standard test method for softening point of bitumen (ring-and-ball apparatus).” D36-76, West Conshohocken, PA.
ASTM. (1989). “Test method for resistance of plastic flow of bituminous mixtures using Marshall apparatus.” ASTM standards, D1559, West Conshohocken, PA.
ASTM. (2005). “Standard test method for soundness of aggregates by use of sodium sulfate or magnesium sulfate.” C88, West Conshohocken, PA.
ASTM. (2006a). “Standard test method for resistance to degradation of small-size coarse aggregate by abrasion and impact in the Los Angeles machine.” C131, West Conshohocken, PA.
ASTM. (2006b). “Standard test methods for uncompacted void content of fine aggregate (as influenced by particle shape, surface texture, and grading).” C1252, West Conshohocken, PA.
ASTM. (2007). “Standard test method for ductility of bituminous materials.” D113-07, West Conshohocken, PA.
ASTM. (2010a). “Standard test methods for specific gravity of soil solids by water pycnometer.” C854, West Conshohocken, PA.
ASTM. (2010b). “Standard test method for flat particles, elongated particles, or flat and elongated particles in coarse aggregate.” D4791, West Conshohocken, PA.
ASTM. (2012a). “Standard test method for density, relative density (specific gravity), and absorption of coarse aggregate.” C127, West Conshohocken, PA.
ASTM. (2012b). “Standard test method for density, relative density (specific gravity), and absorption of fine aggregate.” C128, West Conshohocken, PA.
Bhasin, A. (2006). “Development of method to quantify bitumen-aggregate adhesion and loss of adhesion due to water.” Ph.D. dissertation, Texas A&M Univ., College Station, TX.
Bhasin, A., Little, D., Vasconcelus, K. L., and Masad, E. (2007). “Surface free energy to identify moisture sensitivity of materials for asphalt mixes.”, Transportation Research Board, Washington, DC, 37–45.
Button, J. W., and Epps, J. A. (1983). “Evaluation of methods of mixing lime in asphalt pavement mixtures.”, Texas Transportation Institute, Texas A&M Univ., College Station, TX.
Cheng, D. (2002). “Surface free energy of asphalt-aggregate system and performance analysis of asphalt concrete.” Ph.D. dissertation, Texas A&M Univ., College Station, TX.
Collins, R. (1988). “Status report on the use of hydrated lime in asphaltic concrete mixtures in Georgia.” Materials and Research Rep., Georgia Dept. of Transportation, Atlanta.
Epps, M. A., et al. (2003). “Topic 7: Field experience.” Moisture sensitivity of asphalt pavements: A national seminar, Transportation Research Board, Washington, DC.
Good, R. J., and Van Oss, C. J. (1971). “The modern theory of contact angle and the hydrogen bond components of surface energies.” Modern approach to wettability, Plenum, New York.
Hefer, A. W., Bhasin, A., and Little, D. N. (2006). “Bitumen surface energy characterization using a contact angle approach.” J. Mater. Civ. Eng., 18(6), 759–767.
Kim, Y. R., Lutif, J. S., Bhasin, A., and Little, N. D. (2008). “Evaluation of moisture damage mechanisms and effects of hydrated lime in asphalt mixtures through measurements of mixture component properties and performance testing.” J. Mater. Civ. Eng., 20(10), 659–667.
Kumar, P., and Anand, P. (2012). “Laboratory study on moisture susceptibility of dense graded mixes.” J. Transp. Eng., 138(1), 105–113.
Little, D. N., and Epps, J. A. (2001). “The benefits of hydrated lime in hot-mix asphalt.” Final Rep. for National Lime Association, National Lime Association, Arlington, VA.
Little, D. N., and Peterson, J. C. (2005). “Unique effects of hydrated lime filler on the performance-related properties of asphalt cements: Physical and chemical interactions revisited.” J. Mater. Civ. Eng., 17(2), 207–218.
McCann, M., and Sebaaly, P. E. (2003). “Evaluation of moisture sensitivity and performance of lime in hot-mix asphalt—Resilient modulus, tensile strength, and simple shear tests.”, Transportation Research Board, Washington, DC, 9–16.
Mercado, A. E. (2007). “Influence of fundamental material properties and air void structure on moisture damage of asphalt mixes.” Ph.D. dissertation, Texas A&M Univ., College Station, TX.
Peltonen, P. V. (1992). “Road aggregate choice based on silicate quality and bitumen adhesion.” J. Transp. Eng., 118(1), 50–61.
Tarefder, R. A., and Zaman, A. M. (2010). “Nanoscale evaluation of moisture damage in polymer modified asphalts.” J. Mater. Civ. Eng., 22(7), 714–725.
Xiao, F., Zhao, W., and Amirkhanian, S. N. (2010). “Influence of antistripping additives on moisture susceptibility of warm mix asphalt mixtures.” J. Mater. Civ. Eng., 22(10), 1047–1055.
Zollinger, C. (2005). “Application of surface energy measurements to evaluation moisture susceptibility of asphalt and aggregates.” M.S. thesis, Texas A&M Univ., College Station, TX.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jan 7, 2012
Accepted: Aug 9, 2012
Published online: Aug 27, 2012
Discussion open until: Jan 27, 2013
Published in print: Aug 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.