Load-Transfer Efficiencies of Rigid Airfield Pavement Joints Based on Stresses and Deflections
Publication: Journal of Materials in Civil Engineering
Volume 23, Issue 8
Abstract
Load-transfer efficiency (LTE) of jointed concrete pavement is typically measured by the ratio of unloaded and loaded slab deflection. However, the maximum tensile stress in a slab is one of the critical mechanical responses that influences the performance of the jointed concrete pavement. Therefore, stress-based load-transfer efficiency, defined as stress reduction in the loaded slab because of the presence of an adjacent unloaded slab, is often considered an appropriate way to quantify LTE. Strain gauge data from full-scale tests collected by the Federal Aviation Administration were analyzed to compute the stress-based LTE of joints under moving loads. The effect of static aircraft gear loads and slab size on the LTE of joints was analyzed by using a two-dimensional finite-element program. FEM-calculated stress-based LTE under static aircraft loading on average was 38% lower than that measured under moving loads. LTE values were similar under various gear positions, gear configurations, and different slab sizes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to acknowledge the Federal Aviation Administration because the data used in this study were obtained from full-scale testing carried out at FAA’s National Airport Pavement Test Facility. This work is funded by the Federal Aviation Administration under research grant No. FAA05-G-016.
References
Ahlvin, R. G. (1991). “Origin of developments for structural design of pavements.” Technical Rep. GL-91-26, U.S. Army Corps of Engineers.
Brill, D. R., and Guo, E. H. (2000). “Load transfer in rigid airport pavement joints.” Proc., 26th Int. Air Transportation Conf., San Francisco.
Federal Aviation Administration (FAA). (1995). “Airport pavement design and evaluation.” Advisory Circular 150/5320-6D, Washington, DC.
Federal Aviation Administration (FAA). (2004). “Use of nondestructive testing in the evaluation of airport pavements.” Advisory Circular 150/5370-11A, Washington, DC.
Federal Aviation Administration (FAA). (2009). “FEAFAA—3D finite element based pavement analysis procedure.” 〈http://www.airporttech.tc.faa.gov/pavement/3dfem.asp〉.
Galaxy Scientific. (2004). JSLAB 2004 user’s manual, Federal Highway Administration, Washington, DC.
Guo, E. H. (2001). “Back-estimation of slab curling and joint stiffness.” Proc., 7th Int. Conf. on Concrete Pavements, Orlando, FL, 39–54.
Guo, E. H. (2003). “Proof and comments on extensively used assumption in PCC pavement analysis and evaluation.” J. Transp. Eng., 129(2), 219–220.
Guo, E. H. (2009). “Joint modeling for JPCP: Successes and pending problems.” Proc., Bearing Capacity of Roads, Railways and Airfields Conf., Univ. of Illinois, Urbana-Champaign, IL.
Guo, H., Petch, F., and Ricalde, L. (2010). “Analysis of concrete pavement strain data and behaviour during joint formation.” Int. J. Pavement Eng., 11(3), 173–187.
Guo, E. H., Sherwood, J. A., and Snyder, M. B. (1995). “Component dowel-bar model for load-transfer systems in PCC pavements.” J. Transp. Eng., 121(3), 289.
Hall, K. T., and Mohseni, A. (1991). “Back-calculation of asphalt concrete-overlaid portland cement concrete pavement layer modulii.” Transportation Research Record 1293, Transportation Research Board, Washington, DC, 112–123.
Hammons, M. I. (1998). “Advanced pavement design: Finite element modeling for rigid pavement joints. Report II: Model development.” Publication DOT/FAA/AR-97/7, Federal Aviation Administration, Washington, DC.
Hammons, M. I., and Ioannides, A. M. (1997). “Finite element modeling for rigid pavement joints. Report I: Background investigations.” Publication DOT/FAA/AR-95/85, Federal Aviation Administration, Washington, DC.
Hammons, M. I., Pittman, D. W., and Mathews, D. D. (1995). “Effectiveness of load transfer devices.” Publication DOT/FAA/AR-95/80, Federal Aviation Administration, Washington, DC.
Hayhoe, G. F. (2004). “Traffic testing results from the FAA’s national airport pavement test facility.” 2nd Int. Conf. on Accelerated Pavement Testing, Univ. of Minnesota, Minneapolis.
Huang, Y. H., and Chou, Y. T. (1978). “Discussion on finite element analysis of jointed or cracked pavements.” Transportation Research Record 671, Transportation Research Board, Washington, DC, 17–18.
Huang, Y. H., and Wang, S. T. (1973). “Finite element analysis of concrete slabs and its implications for rigid pavement design.” Highway Research Board No. 446, 55–69.
Ioannides, A. M., and Korovesis, G. T. (1992). “Analysis and design of doweled slab-on-grade pavement systems.” J. Transp. Eng., 118, 745–768.
Kawa, I., Brill, D. R., and Hayhoe, G. F. (2007). “FAARFIELD—New airport thickness design software.” Proc., FAA Worldwide Technology Transfer Conf., Washington, DC.
Kawa, I., Guo, E. H., Hayhoe, G. F., and Brill, D. R. (2002). “Implementation of rigid pavement thickness design for new pavements.” Proc., FAA Technology Transfer Conf., Washington, DC.
Khazanovich, L.,and Gotlif, A. (2005). “Evaluation of PCC joint stiffness using LTPP data.” Proc., 8th Int. Conf. on Concrete Pavements, International Society for Concrete Pavements, Washington, DC, 1120–1137.
Maitra, S. R., Reddy, K. S., and Ramachandra, L. S. (2009). “Load transfer characteristics of dowel bar system in jointed concrete pavement.” J. Transp. Eng., 135(11), 813–821.
Mehta, Y., Cleary, D., Wadkar, A., Zapata, A., Musumeci, L., and Kettleson, W. (2010). “Analysis of model for evaluation of joint load transfer efficiency using NAPTF data.” Quarterly Progress Rep., Federal Aviation Administration, Washington, DC.
National Airport Pavement Test Facility (NAPTF). (2008). 〈http://www.airporttech.tc.faa.gov/naptf〉.
Nishizawa, T., Fukuda, T., and Matsuno, S. (1989). A refined model of doweled joints for concrete pavement using FEM analysis, Purdue Univ., Lafayette, IN, 735–745.
Ricalde, L. (2003). “Portland cement concrete test strip pavement at the FAA National Airport Pavement Test Facility (NAPTF).” Airfield pavements. Challenges and new technologies, Las Vegas, 217–230.
Ricalde, L. (2007). “Analysis of HWD data from CC2 traffic tests at the National Airport Pavement Test Facility.” Proc., FAA Worldwide Technology Transfer Conf., Washington, DC.
Tabatabaie, A. M., and Barenberg, E. J. (1978). “Finite element analysis of jointed or cracked concrete pavements.” Transportation Research Record 671, Transportation Research Board, Washington, DC, 11–19.
Yu, X., Zhou, Y., Peng, J., Tan, Z., and Guo, E. (2010). “Joint load transfer efficiency of rigid pavement considering dynamic effects under a single moving load.” Proc., FAA Worldwide Technology Transfer Conf., Washington, DC.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Apr 19, 2010
Accepted: Feb 3, 2011
Published online: Feb 4, 2011
Published in print: Aug 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.