Nondestructive Assessment of Axial Load–Deflection Behavior of Drilled Shafts for a Suspension Bridge
Publication: Journal of Infrastructure Systems
Volume 18, Issue 1
Abstract
The new Río Cuarto Bridge, currently under construction in the Province of Córdoba, Argentina, consists of a 110-m long, cable-stayed main span with a prestressed concrete deck, steel pylons, and two 50-m–long side spans founded on groups of drilled shafts. The construction method, structural configuration of the superstructure, and post-tensioning sequence of the cables required a detailed characterization of the axial load behavior of the drilled shafts, both for the temporary support shafts and the foundation piers. Small-strain and working load level predictions were made during design, on the basis of conventional site investigation information and in situ geophysical testing. A series of nondestructive evaluations, coupled with nonlinear extrapolations calibrated to represent the measured small-strain range, were carried out in lieu of conventional verification of design predictions by means of more cumbersome large-strain testing. The testing program consisted on monitoring accelerations generated at the top of the shaft as a result of a small amplitude dynamic load measured by means of a dynamic force transducer. A nonlinear numerical model was then calibrated so as to reproduce the initial stiffness measured during the small-strain testing program to extrapolate the load-deflection curve into the service load range and thus define load-deflection curves of the shafts at each pier location up to service load levels. To obtain an experimental validation of the approach at the site, a conventional static load test, carried up to the service load level, was performed on a main pier shaft. Results showed a reasonable agreement between the nondestructive evaluation with nonlinear extrapolation, large-strain measurements, and design predictions for the main pier shafts, whereas some differences were observed between the design predictions and small-strain measurements at other locations, primarily as a result of as-built conditions unforeseen in the original design. Thus, the nondestructive testing program was instrumental in the verification of the as-built behavior of the shafts and allowed the development of load-deflection curves for the drilled shafts that accurately represented the behavior up to the service load level.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (2008). AASHTO LRFD bridge design specifications, customary U.S. units, 4th Ed., Washington, DC.
ASTM. (1996). “Standard test method for piles under static axial compression load.” D1143-81, West Conshohocken, PA.
Caballero, C. R. (2006). “Evaluación numérico experimental del comportamiento bajo carga axial de pilotes.” Doctoral dissertation, Univ. Nacional de Córdoba, Córdoba, Argentina.
Caballero, C. R., Pinto, F., and Prato, C. A. (2003). “Load-deflection curve of drilled shafts by small strain dynamic tests coupled with nonlinear numerical model.” Proc., 12th Pan-American Conf. on Soil Mechanics and Geotechnical Engineering/Soil and Rock America 2003, Verlag Gluckauf, Essen, Germany, 1809–1816.
Chin, F. K. (1970). “Estimation of the ultimate load of piles from tests not carried to failure.” Proc., 2nd Southeast Asian Conf. on Soil Engineering, Southeast Asian Society of Soil Engineering, Singapore.
Paquet, J., and Briard, M. (1976). “Controle non detructif des pieux en beton.” Ann. Inst. Tech. Batim. Trav. Publics, 337, 50–80.
Pinto, F., and Prato, C. A. (2006). “Three dimensional indirect boundary element method formulation for dynamic analysis of frames buried in semi-infinite elastic media.” J. Eng. Mech., 132(9), 967–978.
Randolph, M. F., and Wroth, C. P. (1978). “Analysis of deformation of vertically loaded piles.” J. Geotech. Engrg. Div., 104(12), 1465–1488.
Reese, L. C., and O’Neill, M. W. (1988). “Drilled shafts: Construction procedures and design methods.” U.S. Dept. of Transportation, FHWA-HI-88-042, Dallas, USA.
Stokoe, K. H., Wright, S. G., Bay, J. A., and Roesset, J. M. (1994). “Characterization of geotechnical sites by SASW method.” Technical review: Geophysical characterization of sites, ISSMFE technical committee 10, R. D. Woods, ed., Oxford Publishers, New Delhi, India.
Information & Authors
Information
Published In
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Jan 12, 2010
Accepted: Apr 7, 2011
Published online: Feb 15, 2012
Published in print: Mar 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.