Channel Flow Measurement Using Portable Conical Central Baffle
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Irrigation and Drainage Engineering
Volume 145, Issue 11
Abstract
An analytically derived discharge prediction model for a conical mobile flume, referred to as a conical central baffle (CCB), is presented. The flume is suitable for use in small rectangular channels in agricultural fields or wastewater channels. The flume consists of a cone-shaped object positioned axially in a nearly horizontal prismatic open rectangular channel to produce a venturi effect. The conical obstruction has good stability against the water current owing to its lower center of gravity and can measure a wider range of flows due to its similarity to a V-notch weir. The presence of a conical obstruction alters the cross-section of a rectangular channel at different locations, which requires development of parameters related to the geometry of the cone and channel. A model was proposed to predict flow rates in the channel using the energy concept. The proposed model was tested and modified using different laboratory flumes for various flow rates. The flow rate values obtained using the proposed approach produced an error within 9% when compared with the actual flow rates. The experimental results thus validated the developed model. This flume can be used as a mobile measuring device for temporary flow measurements in small rectangular open channels with the presented approach.
Get full access to this article
View all available purchase options and get full access to this article.
References
Badar, A. M., and A. D. Ghare. 2012. “Development of discharge prediction model for trapezoidal canals using simple portable flume.” Int. J. Hydraul. Eng. 1 (5): 37–42. https://doi.org/10.5923/j.ijhe.20120105.02.
Cornish, G., B. Bosworth, C. Perry, and J. Burke. 2004. Water charging in irrigated agriculture. An analysis of international experience. Rome: Food and Agriculture Organization.
Ferro, V. 2002. “Discussion of ‘Simple flume for flow measurement in open channel’ by Zohrab Samani and Henry Magallanez.” J. Irrig. Drain. Eng. 128 (2): 129–131. https://doi.org/10.1061/(ASCE)0733-9437(2002)128:2(129).
Ferro, V. 2016. “Simple flume with a central baffle.” Flow Meas. Instrum. 52 (Dec): 53–56. https://doi.org/10.1016/j.flowmeasinst.2016.09.006.
Ghare, A. D., and A. M. Badar. 2014. “Experimental studies on the use of mobile cylinders for measurement of flow through rectangular channels.” Int. J. Civ. Eng. 12 (4): 504–511.
Hager, W. H. 1985. “Modified venturi channel.” J. Irrig. Drain. Eng. 111 (1): 19–35. https://doi.org/10.1061/(ASCE)0733-9437(1985)111:1(19).
Hager, W. H. 1986. “Modified trapezoidal venturi channel.” J. Irrig. Drain. Eng. 112 (3): 225–241. https://doi.org/10.1061/(ASCE)0733-9437(1986)112:3(225).
Hager, W. H. 1988. “Mobile flume for circular channel.” J. Irrig. Drain. Eng. 114 (3): 520–534. https://doi.org/10.1061/(ASCE)0733-9437(1988)114:3(520).
Healy, L. H., and R. L. Ontkean. 2015. “Impact of non-level operation of a circular flume on discharge measurement.” In Proc., CSBE/SCGAB 2015 Annual Conf., Canadian Society of Bioengineering, Winnipeg, Manitoba: Canadian Society of Bioengineering.
Kolavani, F. L., M. Bijankhan, C. Di Stefano, V. Ferro, and A. M. Mazdeh. 2018. “Flow measurement using circular portable flume.” Flow Meas. Inst. 62 (2018): 76–83. https://doi.org/10.1016/j.flowmeasinst.2018.05.008.
Kolavani, F. L., M. Bijankhan, C. Di Stefano, V. Ferro, and A. M. Mazdeh. 2019. “Experimental study of central baffle flume.” J. Irrig. Drain. Eng. 145 (3): 62. https://doi.org/10.1061/(ASCE)IR.1943-4774.0001370.
Matter, H. A., M. Khadr, and I. M. H. Rashwan. 2017. “Mobile flume for inverted semicircular open channel.” Mansoura Eng. J. 42 (4): 1–8.
Parshall, R. L. 1926. “The improved venturi flume.” Trans. ASCE 89 (Mar): 841–880.
Peruginelli, A., and F. Bonacci. 1997. “Mobile prisms for flow measurement in rectangular channels.” J. Irrig. Drain. Eng. 123 (3): 170–174. https://doi.org/10.1061/(ASCE)0733-9437(1997)123:3(170).
Replogle, J. A. 1975. “Critical flow flumes with complex cross section.” Proc., ASCE Irrigation and Drainage Division Special Conf., Reston, VA: ASCE.
Robinson, A. R., and A. R. Chamberlain. 1960. “Trapezoidal flumes for open channel flow measurement.” Trans. Am. Soc. Agric. Eng. 3 (2): 120–128. https://doi.org/10.13031/2013.41138.
Samani, Z. 2017. “Three simple flumes for flow measurement in open channels.” J. Irrig. Drain. Eng. 143 (6): 04017010. https://doi.org/10.1061/(ASCE)IR.1943-4774.0001168.
Samani, Z., S. Jorat, and M. Yousaf. 1991. “Hydraulic characteristics of a circular flume.” J. Irrig. Drain. Eng. 117 (4): 558–566. https://doi.org/10.1061/(ASCE)0733-9437(1991)117:4(558).
Samani, Z., and H. Magallanez. 1993. “Measuring water in trapezoidal canals.” J. Irrig. Drain. Eng. 119 (1): 181–186. https://doi.org/10.1061/(ASCE)0733-9437(1993)119:1(181).
Samani, Z., and H. Magallanez. 2000. “Simple flume for flow measurement in open channel.” J. Irrig. Drain. Eng. 126 (2): 127–129. https://doi.org/10.1061/(ASCE)0733-9437(2000)126:2(127).
Skogerboe, G. V., and M. L. Hyatt. 1967. “Rectangular cut throat flumes.” J. Irrig. Drain. Eng. Div. 98 (4): 569–583.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jul 27, 2018
Accepted: Jul 15, 2019
Published online: Sep 10, 2019
Published in print: Nov 1, 2019
Discussion open until: Feb 10, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.