Experimental Study of Flow past a Warped Transition
Publication: Journal of Irrigation and Drainage Engineering
Volume 143, Issue 8
Abstract
Irrigation networks use a warped transition to connect a narrow rectangular channel section with a relatively wide trapezoidal earth-channel section. The flow through the transition often separates from its sidewalls. This can cause significant head losses and increase the risk of eroding the downstream channel, which is undesirable. This paper experimentally investigates the use of a single vane and three vanes located in the warped transition to reduce flow separation. Laser Doppler anemometry measurements of flow velocity were obtained and used for the determination of three-dimensional flow parameters, including the longitudinal flow profile, energy loss in the transition, and maximum velocity in the transition exit flow. The details of flow separation, turbulence intensity, and secondary flow characteristics were studied. The experimental results indicated that the three-vane system was the most efficient transition case, producing such desirable characteristics as flow uniformity, the reduction of secondary flow intensity, and the reduction of maximum velocity in a short reach of the downstream channel. The improvements of the flow characteristics in vane systems are attributed to the effective reduction of flow separation and hence the energy loss. The findings from this experimental study have a direct application to the design of efficient irrigation channels.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study received financial support from the National Sciences and Engineering Research Council of Canada through separate discovery grants held by A. S. Ramamurthy and S. S. Li, respectively.
References
Abbott, D. E., and Kline, S. J. (1962). “Experimental investigation of subsonic turbulent flow over single and double backward facing steps.” J. Basic Eng., 84(3), 317–325.
Alauddin, M., and Basak, B. C. (2006). “Development of an expansion transition in open channel subcritical flow.” J. Civ. Eng., 34(2), 91–101.
Asnaashari, A., Akhtari, A. A., Dehghani, A. A., and Bonakdari, H. (2016). “Experimental and numerical investigation of the flow field in the gradual transition of rectangular to trapezoidal open channels.” Eng. Appl. Comput. Fluid Mech., 10(1), 272–282.
Basak, B. C., and Alauddin, M. (2010). “Efficiency of an expansive transition in an open channel subcritical flow.” DUET J., 1(1), 27–32.
Chaturvedi, R. S. (1963). “Expansive subcritical flow in open channel transitions.” J. Inst. Eng., 43, 447–487.
Chow, V. T. (1959). Open channel hydraulics, McGraw-Hill, New York.
DOT. (1983). “Hydraulic design of energy dissipaters for culverts and channels.”, Washington, DC.
Han, S. S., Ramamurthy, A. S., and Biron, P. M. (2011). “Characteristics of flow around open channel 90° bends with vanes.” J. Irrig. Drain. Eng., 668–676.
Haque, A. (2008). “Some characteristics of open channel transition flow.” Master’s thesis, Dept. of Building, Civil and Environmental Engineering, Concordia Univ., Montréal.
Henderson, F. M. (1966). Open channel flow, Prentice-Hall, Upper Saddle River, NJ.
Hinds, J. (1928). “The hydraulic design of flume and siphon transitions.” Trans. Am. Soc. Civ. Eng., 92(1), 1423–1459.
Ippen, A. T. (1949). “Channel transitions and controls.” Proc., 4th Hydraulics Conf. of Iowa Institute of Hydraulic Research: Engineering hydraulics, Wiley, New York, 496–588.
Isbash, S. V., and Lebedev, I. V. (1961). “Change of natural streams during construction of hydraulic structures.” Proc., 9th Congress of IAHR, Yugoslav Association for Hydraulic Research, Belgrade, Yugoslavia, 1114–1121.
Mitra, A. C. (1940). “Report on the model experiments of fluming of bridges on Purva branch.”, United Provinces Irrigation Research Institute, Roorkee, India, 94–98.
Morris, H. M., and Wiggert, J. M. (1972). Applied hydraulics in engineering, 2nd Ed., Ronald, New York.
Najafi-Nejad-Nasser, A., and Li, S. S. (2015). “Reduction of flow separation and energy head losses in expansions using a hump.” J. Irrig. Drain. Eng., 04014057.
Ramamurthy, A. S., Basak, S., and Rao, P. R. (1970). “Open channel expansions fitted with local hump.” J. Hydraul. Div., 96(HY5), 1105–1113.
Roshko, A. (1953). “On the drag and shedding frequency of two-dimensional bluff bodies.”, National Advisory Committee on Aeronautics, Washington, DC.
Scobey, F. C. (1933). “The flow of waters in flumes.”, USDA, Washington, DC.
Swamee, P. K., and Basak, B. C. (1991). “Design of rectangular open-channel expansion transitions.” J. Irrig. Drain. Eng., 827–838.
Swamee, P. K., and Basak, B. C. (1992). “Design of trapezoidal expansive transitions.” J. Irrig. Drain. Eng., 61–73.
Swamee, P. K., and Basak, B. C. (1993). “Comprehensive open-channel expansion transition design.” J. Irrig. Drain. Eng., 1–17.
Vittal, N., and Chiranjeevi, V. V. (1983). “Open channel transitions: Rational method of design.” J. Hydraul. Eng., 99–115.
Information & Authors
Information
Published In
Journal of Irrigation and Drainage Engineering
Volume 143 • Issue 8 • August 2017
Copyright
©2017 American Society of Civil Engineers.
History
Received: Nov 8, 2016
Accepted: Feb 13, 2017
Published online: May 10, 2017
Published in print: Aug 1, 2017
Discussion open until: Oct 10, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.