Discussion of “Accuracy of Global Microirrigation Distribution Uniformity Estimates” by Stuart W. Styles, Charles M. Burt, Franklin Gaudi, and Sierra Orvis
This article is a reply.
VIEW THE ORIGINAL ARTICLEPublication: Journal of Irrigation and Drainage Engineering
Volume 136, Issue 4
Get full access to this article
View all available purchase options and get full access to this article.
References
Bralts, V. F., Wu, I. P., and Gitlin, H. M. (1981). “Manufacturing variation and drip uniformity.” Trans. ASAE, 24, 113–119.
Burt, C. M. (2004). “Rapid field evaluation of drip and microspray distribution uniformity.” Irrig. Drain. Syst., 18, 275–297.
Burt, C. M., Walker, R., and Styles, S. W. (1992). Irrigation system evaluation manual, Revision 1992, Cal Poly Irrigation Training and Research Center, San Luis Obispo, Calif.
Chandrakanth, M. S., Lau, L. S., and Wu, I. P. (1988). “Plugging evaluation in reuse of primary wastewater effluent for drip irrigation.” Congress Proc., 4th Int. Micro-Irrigation Congress, Vol. 2, Albury-Wodonga, Victoria, Australia.
Clemmens, A. J., and Solomon, K. H. (1997). “Estimation of global irrigation distribution uniformity.” J. Irrig. Drain. Eng., 123(6), 454–461.
Karmeli, D., and Keller, J. (1974). Trickle irrigation design, Rain Bird Sprinkler Manufacturing Corp, Glendora, Calif.
Nakayama, F. S., and Bucks, D. A. (1981). “Emitter clogging effects on trickle irrigation uniformity.” Trans. ASAE, 24(1), 77–80.
Peng, G. F., Wu, I. P., and Phene, C. J. (1986). “Temperature effects on drip line hydraulics.” Trans. ASAE, 29(1), 211–215.
Pitts, D. J., Haman, D. Z., and Smajstrla, A. G. (1990). “Causes and prevention of emitter plugging in microirrigation systems.” Institute of Food and Agricultural Science Bulletin No. 258, Univ. of Florida, Gainesville, Fla.
Solomon, K. (1979). “Manufacturing variation of emitters in trickle irrigation systems.” Trans. ASAE, 22(5), 1034–1038.
Styles, S. W., Burt, C. M., Gaudi, F., and Orvis, S. (2008). “Accuracy of global microirrigation distribution uniformity estimates.” J. Irrig. Drain. Eng., 134(3), 292–297.
Wei, Q., Shi, Y., Lu, G., Dong, W., and Huang, S. (2008). “Rapid evaluations of anticlogging performance of drip emitters by laboratorial short-cycle tests.” J. Irrig. Drain. Eng., 134(3), 298–304.
Wu, I. P. (1997). “An assessment of hydraulic design of micro-irrigation systems.” Agric. Water Manage., 32, 275–284.
Wu, I. P., Feng, J. S., and Yabusaki, K. (1989). “Emitter spacing and uniformity of irrigation application.” Proc., 1989 Int. Summer Meeting, ASAE Paper No. 89-2080.
Wu, I. P., Irudayaraj, J. M., and Feng, J. S. (1988a). “Grouping effect on the uniformity of drip irrigation.” Proc., 4th Int. Micro-Irrigation Congress, Paper No. 10-4, Vol. 1.
Wu, I. P., Irudayaraj, J. M., and Feng, J. S. (1988b). “Plugging evaluation for a drip irrigation submain unit.” Proc., Int. Winter Meeting of ASAE, ASAE Paper No. 88–2062.
Wu, I. P., Lin, B. Y., and Lau, L. S. (1991). “Plugging evaluation in the re-use of sewage effluent by drip irrigation.” Proc., ASCE National Conference, ASCE, New York, 780–786.
Wu, I. P., and Phene, C. J. (1984). “Temperature effect on drip emitters and lateral lines.” Proc., Winter Meeting of ASAE, ASAE Paper No. 84-2628.
Wu, I. P., Yabusaki, K. Y., and Irudayaraj, J. M. (1985). “Computer simulation of total emitter flow variation: Drip/trickle irrigation in action.” Proc., 3rd Int. Micro-Irrigation Congress on Drip/Trickle Irrigation, Vol. 2, 873–886.
Yıldırım, G. (2006). “Hydraulic analysis and direct design of multiple outlets pipelines laid on flat and sloping lands.” J. Irrig. Drain. Eng., 132(6), 537–552.
Yıldırım, G. (2007a). “Analytical relationships for designing multiple outlets pipelines.” J. Irrig. Drain. Eng., 133(2), 140–154.
Yıldırım, G. (2007b). “An assessment of hydraulic design of trickle laterals considering effect of minor losses.” Irrig. Drain., 56(4), 399–421.
Yıldırım, G. (2008a). “Simplified procedure for hydraulic design of small-diameter plastic pipes.” Irrig. Drain., 58(3), 209–233.
Yıldırım, G. (2008b). “Determining operating inlet pressure head incorporating uniformity parameters for multioutlet plastic pipelines.” J. Irrig. Drain. Eng., 134(3), 341–348.
Information & Authors
Information
Published In
Copyright
© 2010 ASCE.
History
Received: Nov 14, 2008
Accepted: Jan 21, 2009
Published online: Mar 15, 2010
Published in print: Apr 2010
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.