Bed-Load Validation for ISSDOTv2
Publication: Journal of Hydraulic Engineering
Volume 148, Issue 3
Abstract
Bed-load transport is an important process impacting riverine morphology, but until recently it has proven difficult to measure in large sand-bed rivers. Integrated Section, Surface Difference Over Time, version 2 (ISSDOTv2) method provides a means of quantifying the bed load in large sand-bed rivers. A series of flume experiments, which included frequent measurements of bed topography and an independent measurement of bed load across a range of flows, was used to provide validation for the ISSDOTv2 method. The mean difference between the ISSDOTv2 calculations and the estimated bed load was 5.6% (high flow), 12.9% (medium flow), and 56% (low flow), indicating improved accuracy for higher flow and transport conditions. It was also found that the ISSDOTv2 method responded appropriately to rapid step-downs in flow, as indicated by agreement between ISSDOTv2 load results and accompanying independent measurements of bed load.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Basic hydraulic and load data such as flow rate, slope, flow depth, bed shear, load measurements (Sedflux, estimated, and total), and ISSDOTv2 bed-load measurements that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This study was funded by the USACE’s Regional Sediment Management Program. The authors would also like to acknowledge the ASCE reviewers for their thoughtful comments and suggestions.
References
Abraham, D., T. Pratt, and J. Sharp. 2010. “Measuring bed load transport on the Missouri River using time sequenced bathymetric data.” In Proc., 2nd Joint Federal Interagency Conf. Las Vegas: Subcommittee on Sedimentation.
Abraham, D., J. Shelley, T. McAlpin, D. May, and J. Adenihun. 2016. “Verification of bedload transport formula at the sub-crosssection scale.” In Proc., Int. Conf. on Fluvial Hydraulics. Leiden, Netherlands: CRC Press.
Abraham, D. D. 2009. “A new method for the measurement of bed load transport using time sequenced bathymetric data.” Doctoral dissertation, Iowa Institute of Hydraulic Research, Univ. of Iowa. https://hdl.handle.net/11681/8966.
Abraham, D. D., et al. 2017. Sediment and hydraulic measurements with computed bed load on the Missouri River, Sioux City to Hermann, 2014. Vicksburg, MS: USACE.
Abraham, D. D., R. A. Kuhnle, and A. J. Odgaard. 2011. “Validation of bed-load transport measurements with time-sequenced bathymetric data.” J. Hydraul. Eng. 137 (7): 723–728. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000357.
Bunte, K., and S. R. Abt. 2005. “Effect of sampling time on measured gravel bed load transport rates in a coarse-bedded stream.” Water Resour. Res. 41 (1): W11405. https://doi.org/10.1029/2004WR003880.
Carey, W. P. 1985. “Variability in measured bed load transport rates.” Water Resour. Bull. 21 (1): 39–48. https://doi.org/10.1111/j.1752-1688.1985.tb05349.x.
Chiew, Y.-M., and G. Parker. 1994. “Incipient sediment motion on non-horizontal slopes.” J. Hydraul. Eng. 32 (5): 649–660. https://doi.org/10.1080/00221689409498706.
Claude, N., S. Rodrigues, V. Bustillo, J. G. Bréhéret, J. J. Macaire, and P. Jugé. 2012. “Estimating bedload transport in a large sand-gravel bed river from direct sampling, dune tracking and empirical formulas.” Geomorphology 179 (15): 40–57. https://doi.org/10.1016/j.geomorph.2012.07.030.
Conevski, S., M. Guerrero, A. Winterscheid, C. D. Rennie, and N. Ruther. 2020. “Acoustic sampling effects on bedload quantification using acoustic Doppler current profilers.” J. Hydraul. Res. 58 (6): 982–1000. https://doi.org/10.1080/00221686.2019.1703047.
Dinehart, R. L. 2002. “Bed form movement recorded by sequential single-beam surveys in tidal rivers.” J. Hydrol. 258 (1–4): 25–39. https://doi.org/10.1016/S0022-1694(01)00558-3.
Exner, F. 1925. “Über die Wechselwirkung zwischen Wasser und Geschiebe in Flüssen.” Sitz. Acad. Wiss. Wien Math. Naturwiss. Abt. 134: 165–203.
Gaeuman, D., and R. B. Jacobson. 2007. “Field assessment of alternative bed-load transport estimators.” J. Hydraul. Eng. 133 (12): 1319–1328. https://doi.org/10.1061/(ASCE)0733-9429(2007)133:12(1319).
Garcia, M. 2008. Sedimentation engineering: Processes, measurements, modeling, and practice. Reston, VA: ASCE.
Gaweesh, M. T. K., and L. C. van Rijn. 1994. “Bed-load sampling in sand-bed rivers.” J. Hydraul. Eng. 120 (12): 1364–1384. https://doi.org/10.1061/(ASCE)0733-9429(1994)120:12(1364).
Gomez, B. 1991. “Bedload transport.” Earth Sci. Rev. 31 (2): 89–132. https://doi.org/10.1016/0012-8252(91)90017-A.
Gomez, B., D. W. Hubbell, and H. H. Stevens Jr. 1990. “At-a-point bed load sampling in presence of dunes.” Water Resour. Res. 26 (11): 2717–2731. https://doi.org/10.1029/WR026i011p02717.
Gray, J. R., J. B. Laronne, and J. D. G. Marr. 2010. Bedload-surrogate monitoring technologies: Scientific investigations report 2010-5091. Reston, VA: ASCE.
Gray, J. R., R. H. Webb, and D. W. Hyndman. 1991. “Low-flow sediment transport in the Colorado River.” In Proc., 5th Federal Interagency Sedimentation Conf., 63–71. Las Vegas: Interagency Advisory Committee on Water Data.
Heath, R. E., et al. 2015. Old River control complex sedimentation investigation. Vicksburg, MS: USACE.
Hubbell, D. W. 1964. Apparatus and techniques for measuring bed-load. Washington, DC: USGS.
Hubbell, D. W., and H. H. Stevens. 1986. “Factors affecting accuracy of bedload sampling.” In Proc., 4th Federal Interagency Sedimentation Conf., 20–29. Las Vegas: Subcommittee on Sedimentation.
Hubbell, D. W., H. H. Stevens Jr., J. V. Skinner, and J. P. Beverage. 1985. “New approach to calibrating bed load samplers.” J. Hydraul. Eng. 111 (4): 677–694. https://doi.org/10.1061/(ASCE)0733-9429(1985)111:4(677).
Kuhnle, R. A., and J. B. Southard. 1988. “Bed load transport fluctuations in a gravel bed laboratory channel.” Water Resour. Res. 24 (2): 247–260. https://doi.org/10.1029/WR024i002p00247.
Kuhnle, R. A., D. G. Wren, R. C. Hilldale, B. T. Goodwiller, and W. O. Carpenter. 2017. “Laboratory calibration of impact plates for measuring gravel bed load size and mass.” J. Hydraul. Eng. 143 (12): 06017023. https://doi.org/10.1061/(ASCE)HY.1943-7900.0001391.
Le Guern, J., S. Rodrigues, T. Geay, S. Zanker, A. Hauet, P. Tassi, N. Claude, P. Juge, A. Duperray, and L. Vervunck. 2020. “Relevance of acoustic methods to quantify bedload transport and bedform dynamics in a large sandy-gravel bed river.” Earth Surf. Dyn. 9 (3): 423. https://doi.org/10.5194/esurf-9-423-2021.
Leopold, L. B., and W. W. Emmett. 1976. “Bed load measurements, East Fork, River, Wyoming.” Proc. Natl. Acad. Sci. U.S.A. 73 (4): 1000–1004. https://doi.org/10.1073/pnas.73.4.1000.
McElroy, B., and M. David. 2009. “Nature of deformation of sandy bed forms.” J. Geophys. Res. 114 (F3): F00A04. https://doi.org/10.1029/2008JF001220.
Muste, M., S. Baranya, R. Tsubaki, D. Kim, H. Ho, H. Tsai, and D. Law. 2016. “Acoustic mapping velocimetry.” Water Resour. Res. 52 (5): 4132–4150. https://doi.org/10.1002/2015WR018354.
Naqshband, S., J. S. Ribberink, D. Hurther, and S. J. M. H. Hulscher. 2014. “Bed load and suspended load contributions to migrating sand dunes in equilibrium.” J. Geophys. Res. Earth Surf. 119 (5): 1043–1063. https://doi.org/10.1002/2013JF003043.
Nittrouer, J. A., M. A. Allison, and R. Campanella. 2008. “Bedform transport rates for the lowermost Mississippi River.” J. Geophys. Res. Earth Surf. 113 (F3): F03004. https://doi.org/10.1029/2007JF000795.
Poorhosein, M., H. Afzalimehr, J. Sui, V. P. Singh, and A. Sahar. 2014. “Empirical bed load transport equations.” Int. J. Hydraul. Eng. 3 (3): 93–101. https://doi.org/10.5923/j.ijhe.20140303.03.
Shelley, J., D. D. Abraham, and T. O. McAlpin. 2013. “Removing systemic bias in bed-load transport measurements in large sand-bed rivers.” J. Hydraul. Eng. 139 (10): 1107–1111. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000760.
Simons, D. B., E. V. Richardson, and C. F. Nordin Jr. 1965. Bed load equation for ripples and dunes. US Department of the Interior, Geological Survey.
Singh, A., K. Fienberg, D. J. Jerolmack, J. Marr, and E. Foufoula-Georgiou. 2009. “Experimental evidence for statistical scaling and intermittency in sediment transport rates.” J. Geophys. Res. 114 (F1): F01025. https://doi.org/10.1029/2007JF000963.
Vanoni, V. A. 1975. Sedimentation engineering. Reston, VA: ASCE.
Vanoni, V. A., and N. H. Brooks. 1957. Laboratory studies of the roughness and suspended load of alluvial streams. Rep. No. E-68. Pasadena, CA: Sedimentation Laboratory California Institute of Technology.
Wilbers, A. 2004. The development and hydraulic roughness of subaqueous dunes. Utrecht, Netherlands: The Royal Dutch Geographical Society.
Willis, J. C., and J. F. Kennedy. 1977. Sediment discharge of alluvial streams calculated from bed-form statistics. Iowa City, IA: Iowa Institute of Hydraulic Research.
Wu, W., and S. S. Y. Wang. 2006. “Formulas for sediment porosity and settling velocity.” J. Hydraul. Eng. 132 (8): 858–862. https://doi.org/10.1061/(ASCE)0733-9429(2006)132:8(858).
Information & Authors
Information
Published In
Copyright
© 2022 Published by American Society of Civil Engineers.
History
Received: Apr 22, 2021
Accepted: Nov 8, 2021
Published online: Jan 5, 2022
Published in print: Mar 1, 2022
Discussion open until: Jun 5, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Daniel G. Wren, Roger A. Kuhnle, Eddy J. Langendoen, Tate O. McAlpin, Sediment Transport and Bed Topography for Realistic Unsteady Flow Hydrographs of Varying Length in a Laboratory Flume, Journal of Hydraulic Engineering, 10.1061/JHEND8.HYENG-13769, 150, 4, (2024).
- Tate O. McAlpin, Daniel G. Wren, Keaton E. Jones, David D. Abraham, Roger A. Kuhnle, Clinton S. Willson, Uncertainty for the ISSDOTv2 Bedload Measurement Method, Journal of Hydraulic Engineering, 10.1061/JHEND8.HYENG-13505, 149, 9, (2023).
- Daniel G. Wren, Tate O. McAlpin, James E. Smith, Keaton E. Jones, Roger A. Kuhnle, David D. Abraham, Analysis of Bedforms in the Mississippi River at Vicksburg, Mississippi, for Select Flows 2011–2016, Journal of Hydraulic Engineering, 10.1061/JHEND8.HYENG-13295, 149, 2, (2023).
- S. Baranya, G. Fleit, M. Muste, R. Tsubaki, J. Józsa, Bedload estimation in large sand-bed rivers using Acoustic Mapping Velocimetry (AMV), Geomorphology, 10.1016/j.geomorph.2022.108562, 424, (108562), (2023).
- Jérôme Le Coz, Emeline Perret, Benoît Camenen, David J. Topping, Daniel D. Buscombe, Kate C. P. Leary, Guillaume Dramais, Paul E. Grams, Mapping 2‐D Bedload Rates Throughout a Sand‐Bed River Reach From High‐Resolution Acoustical Surveys of Migrating Bedforms, Water Resources Research, 10.1029/2022WR032434, 58, 11, (2022).