Experimental Investigation of Archimedes Screw Pump
Publication: Journal of Hydraulic Engineering
Volume 146, Issue 8
Abstract
There is essentially no experimental data on Archimedes screw pump performance available in the literature that is sufficiently detailed for model validation. Experiments were conducted on a laboratory scale (0.3-m diameter) Archimedes screw pump to characterize the pumping efficiency of the screw pump at various inlet basin water levels and screw rotation speeds. The results provide new insights into the effect of inlet and outlet basin level on screw pump efficiency. The flow rate of water pumped is proportional to the rotation speed of the screw, and increases with increasing inlet basin depth until the basin level exceeds that needed to fully fill the screw without overflowing. Comparisons are made to available empirical and analytically derived guidelines regarding optimal lower basin water levels, upper basin water levels and rotation rates for an Archimedes screw pump. Some differences are noted between recommended optimal conditions for full-size screws from the literature, and the optimum conditions found for the tested laboratory-size screw. These differences are consistent with expected effects of scaling between different size screws.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
Aspects of this work were financially supported by the Natural Sciences and Engineering Research Council (NSERC) Collaborative Research and Development (CRD) program (Grant No. CRDPJ 433740-12) and Greenbug Energy Inc. (Delhi, ON, Canada). The assistance of Tony Bouk and Brian Weber of Greenbug Energy Inc. is gratefully acknowledged.
References
Boiten, W., A. Dommerholt, and M. Soet. 1995. Handbook on flow measurements in open watercourses. [In Dutch.] Wageningen, the Netherlands: Dept. of Water Management.
Buysse, D., A. M. Mouton, M. Stevens, T. Van den Neucker, and J. Coeck. 2014. “Mortality of European eel after downstream migration through two types of pumping stations.” Fish. Manage. Ecol. 21 (1): 13–21. https://doi.org/10.1111/fme.12046.
Dalley, S., and J. P. Oleson. 2003. “Sennacherib, Archimedes, and the water screw: The context of invention in the ancient world.” Technol. Cult. 44 (1): 1–26. https://doi.org/10.1353/tech.2003.0011.
Koetsier, T., and H. Blauwendraat. 2004. “The Archimedean screw-pump: A note on its invention and the development of the theory.” In Proc., Int. Symp. on History of Machines and Mechanism (HMM04), 181–194. Dordrecht, the Netherlands: Kluwer.
Kozyn, A., and W. D. Lubitz. 2017. “A power loss model for Archimedes screw generators.” Renewable Energy 108 (Aug): 260–273. https://doi.org/10.1016/j.renene.2017.02.062.
Lashofer, A., W. Hawle, I. Kampel, F. Kaltenberger, and B. Pelikan. 2012. “State of technology and design guidelines for the Archimedes screw turbine.” In Proc., Hydro 2012. Surrey, UK: Aqua-Media International.
Lubitz, W. D., 2014. “Gap flow in Archimedes screws.” In Proc., CSME Int. Congress. Ottawa: Canadian Society for Mechanical Engineering.
Mcnabb, C. D., C. R. Liston, and S. M. Borthwick. 2003. “Passage of juvenile Chinook salmon and other fish species through Archimedes lifts and a Hidrostal pump at Red Bluff, California” Trans. Am. Fish. Soc. 132 (2): 326–334. https://doi.org/10.1577/1548-8659(2003)132%3C0326:POJCSA%3E2.0.CO;2.
Monserrat, J., R. G. Ortiz, L. Cots, and J. Barragán. 2015. “Energy saving in a variable-inclination Archimedes screw.” Irrig. Drain. Syst. Eng. 4 (1): 1000133. https://doi.org/10.4172/2168-9768.1000133.
Muysken, J. 1932. “Calculation of the effectiveness of the auger.” [In Dutch.] De Ingenieur 21: 77–91.
Nagel, G. 1968. Archimedean screw pump handbook. Nurnberg, Germany: Ritz-Atro.
Naish, C., D. Dungworth, and T. Doyle. 2012. “Delivering London 2012: The Lee Valley White Water Centre.” Proc. Inst. Civ. Eng. 165 (1): 19–26. https://doi.org/10.1680/cien.2012.165.1.19.
Nuernbergk, D. M., and C. Rorres. 2012. “Analytical model for water inflow of an Archimedes screw used in hydropower generation.” J. Hydrol. Eng. 139 (2): 213–220. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000661.
Rorres, C. 2000. “The turn of the screw: Optimal design of an Archimedes screw.” J. Hydraul. Eng. 126 (1): 72–80. https://doi.org/10.1061/(ASCE)0733-9429(2000)126:1(72).
Vaughan, K. 2006. “Windmills of Holland.” PSA J. 30–33.
Waters, S. R., and G. A. Aggidis. 2015. “Over 2000 years in review: Revival of the Archimedes screw from pump to turbine.” Renewable Sustainable Energy Rev. 51 (Nov): 497–505. https://doi.org/10.1016/j.rser.2015.06.028.
Wijdieks, J., and M. G. Bos. 1994. “Pumps and pumping stations.” In Drainage principles and applications, edited by H. P. Ritzema, 2nd ed. Wageningen, the Netherlands: International Institute for Land Reclamation and Improvement.
Williamson, S. J., B. H. Stark, and J. D. Booker. 2014. “Low head pico hydro turbine selection using a multi-criteria analysis.” Renewable Energy 61 (Jan): 43–50. https://doi.org/10.1016/j.renene.2012.06.020.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Sep 10, 2019
Accepted: Mar 23, 2020
Published online: Jun 12, 2020
Published in print: Aug 1, 2020
Discussion open until: Nov 12, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.