Numerical Simulation of Ripple Evolution under Turbulent Flow Using a Coupled LES and DPM Model
Publication: Journal of Hydraulic Engineering
Volume 144, Issue 11
Abstract
The processes of ripple evolution are studied through numerical simulation using a coupled computational fluid dynamics (CFD)–discrete particle method (DPM) model with focus on discussing the effect of the size of the computational domain on ripple evolution. Ripple-induced form resistance and bed load transport rate are also discussed. Fluid movement is simulated using the CFD computation with the introduction of large eddy simulation for turbulent closure. The movement of sediment particles is simulated using the DPM. It is found from the results of simulation that for a two-dimensional case the ripple evolution involves three stages from wavelet, merging of wavelets to equilibrium. The ripple sizes increase during the merging process and reach a stable state at the end of the merging process. The ripple sizes obtained in the final equilibrium stage are closely related to the streamwise size of the computational domain and have an upper bound for given sediment and flow conditions. If the streamwise size of the computational domain is set to approximately 6 times the ripple length or beyond, the discrepancies among the equilibrium ripple lengths obtained from using different streamwise size of computational domain can be below 9.2%. The ripple lengths modeled in the wavelet stage agree well with the experimental results. During the process of ripple merging, an abrupt reduction in the form resistance and an increase in the bed load transport rate are observed.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was financed by the National Natural Science Foundation of China (Grant No. 51779170) and the Innovative Research Groups of the National Natural Science Foundation of China (Grant No. 51321065).
References
Baas, J. H. 1993. Dimensional analysis of current ripples in recent and ancient depositional environments. Utrecht, Netherlands: Univ. of Utrecht.
Bechteler, W., G. Vogel, and H. J. Vollmers. 1991. “Model investigations on the sediment transport of a lower alpine river.” In Fluvial hydraulics of mountain regions, lecture note in earth sciences, edited by A. Armanini and G. di Silvio, 769–857. Berlin: Springer.
Brown, P. P., and D. F. Lawler. 2003. “Sphere drag and settling velocity revisited.” J. Environ. Eng. 129 (3): 222–231. https://doi.org/10.1061/(ASCE)0733-9372(2003)129:3(222).
Charru, F., J. Bouteloup, T. Bonometti, and L. Lacaze. 2016. “Sediment transport and bedforms: A numerical study of two-phase viscous shear flow.” Meccanica 51 (12): 3055–3065. https://doi.org/10.1007/s11012-016-0553-5.
Chepil, W. S. 1958. “The use of evenly spaced hemispheres to evaluate aerodynamic forces on soil surfaces.” Eos Trans. Am. Geophys. Union 39 (3): 397. https://doi.org/10.1029/TR039i003p00397.
Chou, Y. J., and O. B. Fringer. 2010. “A model for the simulation of coupled flow-bed form evolution in turbulent flows.” J. Geophy. Res. 115 (C10): 1971–1982. https://doi.org/10.1029/2010JC006103.
Coleman, S. E., and B. W. Melville. 1994. “Bed-form development.” J. Hydraul. Eng. 120 (5): 544–560. https://doi.org/10.1061/(ASCE)0733-9429(1994)120:5(544).
Coleman, S. E., and B. W. Melville. 1996. “Initiation of bed forms on a flat sand bed.” J. Hydraul. Eng. 122 (6): 301–310. https://doi.org/10.1061/(ASCE)0733-9429(1996)122:6(301).
Coleman, S. E., and V. I. Nikora. 2009. “Bed and flow dynamics leading to sediment-wave initiation.” Water Resour. Res. 45 (4): 295–296. https://doi.org/10.1029/2007WR006741.
Cundall, P. A., and O. D. L. Strack. 1979. “A discrete numerical model for granular assemblies.” Géotechnique 29 (30): 331–336. https://doi.org/10.1680/geot.1979.29.1.47.
Deen, N. G., M. V. S. Annaland, M. A. V. D. Hoef, and J. A. M. Kuipers. 2007. “Review of discrete particle modeling of fluidized beds.” Chem. Eng. Sci. 62 (1): 28–44. https://doi.org/10.1016/j.ces.2006.08.014.
Einstein, H. A., and N. L. Barbarossa. 1952. “River channel roughness.” Trans. Am. Soc. Civ. Eng. 117 (12): 1121–1132.
Engelund, F. 1966. “Hydraulic resistance of alluvial streams.” J. Hydraul. Div. 92: 315–326.
Gondret, P., M. Lance, and L. Petit. 2002. “Bouncing motion of spherical particles in fluids.” Phys. Fluids 14 (2): 643–652. https://doi.org/10.1063/1.1427920.
Gotoh, H. 1997. “Numerical simulation of sheet flow as granular material.” J. Waterw. Port Coastal Ocean Eng. 123 (6): 329–336. https://doi.org/10.1061/(ASCE)0733-950X(1997)123:6(329).
Guy, H. P., D. B. Simons, and E. V. Richardson. 1966. “Summary of alluvial channel data from flume experiments.” J. Biol. Chem. 283 (8): 5148–5157.
Hunt, J. C. R., A. A. Wray, and P. Moin. 1988. “Eddies, streams and convergence zones in turbulent flows.” In CTR Annual Research Briefs NASA. Stanford, CA: Stanford University Press.
Inagaki, M., T. Kondoh, and Y. Nagano. 2005. “A mixed-time-scale SGS model with fixed model-parameters for practical LES.” J. Fluids Eng. 127 (1): 1–13. https://doi.org/10.1115/1.1852479.
Jain, R., B. Vowinckel, and J. Fröhlich. 2017. “Spanwise particle clusters in DNS of sediment transport over a regular and an irregular bed.” Flow Turbul. Combust. 4: 1–18. https://doi.org/10.1007/s10494-017-9850-x.
Ji, C., D. Liu, and D. Xu. 2015. “Large eddy simulation of sand ripple evolution using discrete particle method.” Chin. J. Theor. Appl. Mech. 47 (4): 613–623. https://doi.org/10.6052/0459-1879-14-254.
Ji, C., A. Munjiza, E. Avital, J. Ma, and J. J. R. Williams. 2013. “Direct numerical simulation of sediment entrainment in turbulent channel flow.” Phys. Fluids 25 (5): 056601. https://doi.org/10.1063/1.4807075.
Kennedy, F. J. 1963. “The mechanics of dunes and antidunes in erodible-bed channels.” J. Fluid Mech. 16 (4): 521–544. https://doi.org/10.1017/S0022112063000975.
Khosronejad, A., and F. Sotiropoulos. 2014. “Numerical simulation of sand waves in a turbulent open channel flow.” J. Fluid Mech. 753 (2): 150–216. https://doi.org/10.1017/jfm.2014.335.
Kidanemariam, A. G., and M. Uhlmann. 2014a. “Direct numerical simulation of pattern formation in subaqueous sediment.” J. Fluid Mech. 750: R21–R213. https://doi.org/10.1017/jfm.2014.284.
Kidanemariam, A. G., and M. Uhlmann. 2014b. “Interface-resolved direct numerical simulation of the erosion of a sediment bed sheared by laminar channel flow.” Int. J. Multiphase Flow 67: 174–188. https://doi.org/10.1016/j.ijmultiphaseflow.2014.08.008.
Kidanemariam, A. G., and M. Uhlmann. 2017. “Formation of sediment patterns in channel flow: Minimal unstable systems and their temporal evolution.” J. Fluid Mech. 818: 716–743. https://doi.org/10.1017/jfm.2017.147.
Langlois, V., and A. Valance. 2007. “Initiation and evolution of current ripples on a flat sand bed under turbulent water flow.” Eur. Phys. J. E 22 (3): 201–208. https://doi.org/10.1140/epje/e2007-00023-0.
Li, M., and B. A. O’Connor. 2000. “Effective roughness of bedforms.” Hydraul. Eng. Software VIII 7: 143–152.
Lin, C. Y. M., and J. G. Venditti. 2013. “An empirical model of subcritical bedform migration.” Sedimentology 60 (7): 1786–1799. https://doi.org/10.1111/sed.12056.
Liu, S.-H., S.-R. Yin, and W. Guo. 2010. “Turbulent flows around and sand dunes in alluvial rivers.” J. Hydrodyn. 22 (1): 103–109. https://doi.org/10.1016/S1001-6058(09)60034-2.
Meyer-Peter, E., and R. Müller. 1948. “Formulas for bed-load transport.” In Vol. 3 of Proc., 2nd Meeting of International Association for Hydraulic Research, 39–64. Stockholm.
Nabi, M., H. J. de Vriend, E. Mosselman, C. J. Sloff, and Y. Shimizu. 2013. “Detailed simulation of morphodynamics. 3: Ripples and dunes.” Water Resour. Res. 49 (9): 5930–5943. https://doi.org/10.1002/wrcr.20457.
Nakagawa, H., and T. Tsujimoto. 1984. “Spectral analysis of sand bed instability.” J. Hydraul. Eng. 110 (4): 467–483. https://doi.org/10.1061/(ASCE)0733-9429(1984)110:4(467).
Nelson, J. M., and J. D. Smith. 1989. “Flow in meandering channels with natural topography.” In River meandering. Water Resources Monograph Number 12, edited by S. Ikeda and G. Parker, 69–102. Washington, DC: American Geophysical Union.
Nguyen, Y. Q., and J. C. Wells. 2015. “Modeling bedform development under turbulent flows using Large-Eddy-Simulation and Immersed-Boundary-Method.” Comput. Phys. 111: 105–113. https://doi.org/10.1016/j.compfluid.2015.01.014.
Niño, Y., and M. García. 1998. “Using Lagrangian particle saltation observations for bedload sediment transport modelling.” Hydrol. Processes 12 (8): 1197–1218. https://doi.org/10.1002/(SICI)1099-1085(19980630)12:8%3C1197::AID-HYP612%3E3.0.CO;2-U.
Osanloo, F., M. R. Kolahchi, S. Mcnamara, and H. J. Herrmann. 2008. “Sediment transport in the saltation regime.” Phys. Rev. E 78 (1): 011301. https://doi.org/10.1103/PhysRevE.78.011301.
Ouriemi, M., P. Aussillous, and É. Guazzelli. 2009. “Sediment dynamics. Part 1. Bed-load transport by laminar shearing flows.” J. Fluid Mech. 636: 295–319. https://doi.org/10.1017/S0022112009007915.
Picciotto, M., C. Marchioli, and A. Soldati. 2005. “Characterization of near-wall accumulation regions for inertial particles in turbulent boundary layers.” Phys. Fluids 17 (9): 98101. https://doi.org/10.1063/1.2033573.
Piomelli, U., and E. Balaras. 2002. “Wall-layer models for eddy simulations.” Annu. Rev. Fluid Mech. 34 (1): 349–374. https://doi.org/10.1146/annurev.fluid.34.082901.144919.
Raichlen, F., and J. F. Kennedy. 1965. “The growth of sediment bed forms from an initially flattened bed.” In Proc., XI Congress of IAHR. Saint Petersburg, Russia: International Association for Hydro-Environment Engineering and Research.
Raudkivi, A. J. 1997. “Ripples on stream bed.” J. Hydraul. Eng. 123: 58–64. https://doi.org/10.1061/(ASCE)0733-9429(1997)123:1(58).
Richards, K. J. 1980. “The formation of ripples and dunes on an erodible bed.” J. Fluid Mech. 99 (3): 597–618. https://doi.org/10.1017/S002211208000078X.
Rouson, D. W. I., and J. K. Eaton. 2001. “On the preferential concentration of solid particles in turbulent channel flow.” J. Fluid Mech. 428: 149–169. https://doi.org/10.1017/S0022112000002627.
Schmeeckle, M. W. 2014. “Numerical simulation of turbulence and sediment transport of medium sand.” J. Geophy. Res. 119 (6): 1240–1262. https://doi.org/10.1002/2013JF002911.
Simeonov, J. A., and J. Calantoni. 2012. “Modeling mechanical contact and lubrication in direct numerical simulations of colliding particles.” Int. J. Multiphase Flow 46: 38–53. https://doi.org/10.1016/j.ijmultiphaseflow.2012.05.008.
Simons, D. B., E. V. Richardson, and C. F. Nordin. 1965. Bedload equation for ripples and dunes. Washington, DC: US Government Printing Office.
Soulsby, R. L. 1997. Dynamics of marine sands: A manual for practical applications. London: Thomas Telford.
Sumer, B. M., and M. Bakioglu. 1984. “On the formation of ripples on an erodible bed.” J. Fluid Mech. 144 (1): 177–190. https://doi.org/10.1017/S0022112084001567.
Sun, R., and H. Xiao. 2016a. “CFD-DEM simulations of current-induced dune formation and morphological evolution.” Adv. Water Resour. 92: 228–239. https://doi.org/10.1016/j.advwatres.2016.03.018.
Sun, R., and H. Xiao. 2016b. “SediFoam: A general-purpose, open-source CFD-DEM solver for particle-laden flow with emphasis on sediment transport.” Comput. Geosci. 89: 207–219. https://doi.org/10.1016/j.cageo.2016.01.011.
Thomas, T. G., and J. J. R. Williams. 1997. “Development of a parallel code to simulate skewed flow over a bluff body.” J. Wind Eng. Ind. Aerodyn. s67–68 (4): 156–167. https://doi.org/10.1016/S0167-6105(97)00070-6.
Vanoni, V. A. 1974. “Factors determining bed forms of alluvial streams.” J. Hydraul. Div. 100 (11): 363–377.
van Rijn, L. C. 1984. “Sediment transport, Part III: Bed forms and alluvial roughness.” J. Hydraul. Eng. 110 (12): 1733–1754. https://doi.org/10.1061/(ASCE)0733-9429(1984)110:12(1733).
Venditti, J. G., M. A. Church, and S. J. Bennett. 2005. “Bed form initiation from a flat sand bed.” J. Geophys. Res. 110 (F1): 19–24. https://doi.org/10.1029/2004JF000149.
Vowinckel, B., T. Kempe, and J. Fröhlich. 2014. “Fluid-particle interaction in turbulent open channel flow with fully-resolved mobile beds.” Adv. Water Resour. 72: 32–44. https://doi.org/10.1016/j.advwatres.2014.04.019.
Wiberg, P. L., and J. D. Smith. 1985. “A theoretical model for saltating grains in water.” J. Geophys. Res. 90 (C4): 7341–7354. https://doi.org/10.1029/JC090iC04p07341.
Williams, P. B., and P. H. Kemp. 1971. “Initiation of ripples on flat sediment beds.” J. Hydraul. Div. 97 (4): 505–522.
Wong, M., and G. Parker. 2006. “Reanalysis and correction of bed-load relation of Meyer-Peter and Müller using their own database.” J. Hydraul. Eng. 132 (11): 1159–1168. https://doi.org/10.1061/(ASCE)0733-9429(2006)132:11(1159).
Yalin, M. S. 1972. Mechanics of sediment transport. Oxford, UK: Pergamon.
Yalin, M. S. 1977. “On the determination of ripple length.” J. Hydraul. Div. 103 (HY4): 439–442.
Yalin, M. S. 1985. “On the determination of ripple geometry.” J. Hydraul. Eng. 111 (8): 1148–1155. https://doi.org/10.1061/(ASCE)0733-9429(1985)111:8(1148).
Yeganeh-Bakhtiary, A., B. Shabani, H. Gotoh, and S. S. Y. Wang. 2009. “A three-dimensional distinct element model for bed-load transport.” J. Hydraul. Eng. 47 (2): 203–212. https://doi.org/10.3826/jhr.2009.3168.
Zedler, E. A., and R. L. Street. 2001. “Large-eddy simulation of sediment transport: Currents over ripples.” J. Hydraul. Eng. 127 (6): 444–452. https://doi.org/10.1061/(ASCE)0733-9429(2001)127:6(444).
Zhao, T., G. T. Houlsby, and S. Utili. 2014. “Investigation of granular batch sedimentation via DEM-CFD coupling.” Granular Matter 16 (6): 921–932. https://doi.org/10.1007/s10035-014-0534-0.
Zhou, Y. C., B. H. Xu, A. B. Yu, and P. Zulli. 2002. “An experimental and numerical study of the angle of repose of coarse spheres.” Powder Technol. 125 (1): 45–54. https://doi.org/10.1016/S0032-5910(01)00520-4.
Zhu, H. P., Z. Y. Zhou, R. Y. Yang, and B. A. Yu. 2007. “Discrete particle simulation of particulate systems: Theoretical developments.” Chem. Eng. Sci. 62 (13): 3378–3396. https://doi.org/10.1016/j.ces.2006.12.089.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Sep 11, 2017
Accepted: May 10, 2018
Published online: Sep 12, 2018
Published in print: Nov 1, 2018
Discussion open until: Feb 12, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.